Graco Pulse Series Instructions de montage

3A5413F

Service Instructions

Pulse®, SDP and SDM Metered

Dispense Valve Repair

For dispensing oil, automatic transmission fluid (ATF), gear oils, antifreeze and

windshield washer solvent.

Not approved for use in explosive atmospheres or hazardous locations. For professional

use only.

Metered Dispense Valve Models: (page 5)

1500 psi (10 MPa, 103 bar) Maximum Working Pressure

Repair Kits

26C287: Pulse Bezel Replacement, page 8

26C403: SDP8/18 Bezel Replacement,

page 8

26C484: SDM8 and SDM18 Bezel

Replacement, page 8

25D906: Swivel Seal and Filter

Replacement, page 12

25D903: Trip Rod Replacement for Pulse

and SDP meters, page 15

26C394: Trip Rod Replacement for SDM8

and SDM18 meters, page 17

25D904: Valve Replacement, page 19

25P665: Power Cable Replacement, page

Related Manuals

3A5412 - Pulse Metered Dispense Valve

Installation and Operation

3A6711 - SMD8 and SDM18 Metered

Dispense Valves Installation and Operation

3A6673 - SDP8 and SDP18 Preset Metered

Dispense Valves Installation and Operation

Important Safety

Instructions

Read all warnings and instructions

in this manual and related Pulse

System manuals. Save all

instructions.

NOTICE

The metered dispense valve is designed to

dispense petroleum-based lubricants,

windshield washer solvent and antifreeze

only. Dispensing brake cleaner and/or

harsh solvents may damage the plastic

components.

Contents

23A5413F

Contents

Warnings ............................................................................. 3

Models ................................................................................. 5

Service ................................................................................ 7

Pressure Relief Procedure .............................................7

Battery Replacement ..................................................... 7

Bezel Replacement ........................................................ 8

Disassembly ............................................................ 8

Reassembly ............................................................. 9

Power Cable Replacement .......................................... 11

Swivel Seal and Strainer Replacement ....................... 12

Trip Rod Replacement or Valve Replacement ...... 13

Disassembly .......................................................... 13

Pulse and SDP Trip Rod Replacement ................. 15

SDM Trip Rod Replacement ................................. 17

Valve Replacement ............................................... 19

Reassembly ................................................................. 20

Parts .................................................................................. 21

Parts .................................................................................. 22

Related Kits ................................................................. 22

Notes ................................................................................. 23

Warnings

3A5413F 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this

equipment. The exclamation point symbol alerts you to a general warning and the hazard

symbols refer to procedure-specific risks. When these symbols appear in the body of this

manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols

and warnings not covered in this section may appear throughout the body of this manual where

applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components

will pierce skin. This may look like just a cut, but it is a serious injury that can result

in amputation. Get immediate surgical treatment.

•Do not point dispensing device at anyone or at any part of the body.

•Do not put your hand over the fluid outlet.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Follow the Pressure Relief Procedure when you stop dispensing and before

cleaning, checking, or servicing equipment.

•Tighten all fluid connections before operating the equipment.

•Check hoses and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the low-

est rated system component. See Technical Specifications in all equipment

manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See

Technical Specifications in all equipment manuals. Read fluid and solvent

manufacturer’s warnings. For complete information about your material, request

Safety Data Sheets (SDSs) from distributor or retailer.

•Turn off all equipment and follow the Pressure Relief Procedure when equip-

ment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately

with genuine manufacturer’s replacement parts only.

•Do not alter or modify equipment. Alterations or modifications may void agency

approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you

are using it.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and

hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

Warnings

43A5413F

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and wind-

shield wiper fluid, be aware that flammable fumes can ignite or explode. To help

prevent fire and explosion:

•Use equipment only in well-ventilated area.

•Eliminate all ignition sources, such as cigarettes and portable electric lamps.

•Ground all equipment in the work area.

•Keep work area free of debris, including rags and spilled or open containers of

solvent and gasoline.

•Do not plug or unplug power cords or turn lights on or off when flammable fumes

are present.

•Use only grounded hoses.

•Stop operation immediately if static sparking occurs or you feel a shock.Do

not use equipment until you identify and correct the problem.

•Keep a working fire extinguisher in the work area.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent seri-

ous injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.

Protective equipment includes but is not limited to:

•Protective eye wear, and hearing protection.

•Respirators, protective clothing, and gloves as recommended by the fluid and

solvent manufacturer.

CALIFORNIA PROPOSITION 65

WARNING: This product can expose you to chemicals known to the State of

California to cause cancer and birth defects or other reproductive harm. For more

information, go to www.P65warnings.ca.gov.

WARNING

Models

3A5413F 5

Models

Pulse

Model

SDP

Model

SDM

Model Swivel

Exten-

sion Nozzle Fluid

Max

Volumetric

Flow Rate

GPM LPM

25M317 26C384 25M404 1/2 NPT Rigid Auto-

matic Oil 8 30

25M318 26C385 25M405 1/2 NPT Rigid Anti-

freeze

Anti-

freeze 8 30

25M319 26C354 25M406 1/2 NPT Flexible Auto-

matic Oil 8 30

25M320 26C355 25M407 1/2 NPT Flexible Anti-

freeze

Anti-

freeze 8 30

25M323 26C356 25M410 1/2 NPT Rigid High

Flow Oil 18 68

25M324 26C357 25M411 1/2 NPT Flexible High

Flow Oil 18 68

25M326 26C358 25M413 1/2 NPT Gear

Lube Manual Gear

Lube 5 19

25M328 N.A. 25M415 1/2 NPT Rigid,

open None WWS* 8 30

25M329 26C360 25M416 3/4 NPT Rigid High

Flow Oil 18 68

25M330 26C361 25M417 3/4 NPT Flexible High

Flow Oil 18 68

25M332 26C362 25M419 1/2 BSPP Rigid Auto-

matic Oil 8 30

25M333 26C363 25M420 1/2 BSPP Rigid Anti-

freeze

Anti-

freeze 8 30

25M334 26C364 25M421 1/2 BSPP Flexible Auto-

matic Oil 8 30

25M335 26C365 25M422 1/2 BSPP Flexible Anti-

freeze

Anti-

freeze 8 30

25M338 26C368 25M425 1/2 BSPP Rigid High

Flow Oil 18 68

25M339 26C369 25M426 1/2 BSPP Flexible High

Flow Oil 18 68

25M341 26C370 25M428 1/2 BSPP Gear

Lube Manual Gear

Lube 5 19

25M343 N.A. 25M430 1/2 BSPP Rigid,

open None WWS* 8 30

25M344 26C372 25M431 3/4 BSPP Rigid High

Flow Oil 18 68

Models

63A5413F

*WWS = Windshield Washer Solvent

25M345 26C373 25M432 3/4 BSPP Flexible High

Flow Oil 18 68

25M347 26C374 25M434 1/2 BSPT Rigid Auto-

matic Oil 8 30

25M348 26C375 25M435 1/2 BSPT Rigid Anti-

freeze

Anti-

freeze 8 30

25M349 26C376 25M436 1/2 BSPT Flexible Auto-

matic Oil 8 30

25M350 26C377 25M437 1/2 BSPT Flexible Anti-

freeze

Anti-

freeze 8 30

25M353 26C378 25M440 1/2 BSPT Rigid High

Flow Oil 18 68

25M354 26C379 25M441 1/2 BSPT Flexible High

Flow Oil 18 68

25M356 26C380 25M443 1/2 BSPT Gear

Lube Manual Gear

Lube 5 19

25M358 N.A. 25M445 1/2 BSPT Rigid,

open None WWS* 8 30

25M359 26C382 25M446 3/4 BSPT Rigid High

Flow Oil 18 68

25M360 26C383 25M447 3/4 BSPT Flexible High

Flow Oil 18 68

Pulse

Model

SDP

Model

SDM

Model Swivel

Exten-

sion Nozzle Fluid

Max

Volumetric

Flow Rate

GPM LPM

Service

3A5413F 7

Service

Pressure Relief Procedure

Follow the Pressure Relief

Procedure whenever you see this

symbol.

1. Turn off power supply to the pump or

close fluid shut off valve (B).

2. Open nozzle.

3. Trigger the metered dispense valve into

a waste container to relieve pressure.

•Pulse meters require an authorized test

dispense within the Pulse Fluid

Management Software to enable the

trigger.

•SDP meters require a preset dispense

activation to enable the trigger.

•SDP meters with Pulse FC enabled

require an enabled dispense card to

authorize a dispense to enable the

trigger.

•SDM meter triggers are always enabled.

4. Open any bleed-type master air valves

and fluid drain valves in the system.

5. Leave the drain valve open until you are

ready to pressurize the system.

Battery Replacement

NOTE: The metered dispense valve does not

have to be taken out of service to replace the

batteries.

•Replace batteries with four AA, alkaline

batteries.

•Be sure to follow the correct polarity as

shown on the installation labels located

on either side of the metered dispense

valve when installing batteries in the

battery compartment (FIG. 2).

•Do not mix different types of batteries

together or old batteries with fresh

ones. Always replace all 4 batteries with

4, fresh, new AA batteries.

To change the battery:

1. Remove screws (36) from the battery

compartment cover (5).

2. Use a small, flat screwdriver to gently pry

the cover away from the metered

dispense valve housing on the bottom

side of the cover, near the extension

attachment as shown in FIG. 1.

3. Remove and separately recycle

batteries according to all applicable

regulations.

4. Install 4 new batteries. See labels on the

each side of the housing and FIG. 2 for

battery orientation.

This equipment stays pressurized until

pressure is manually relieved. To help

prevent serious injury from pressurized

fluid, such as skin injection, splashing fluid

and moving parts, follow the Pressure

Relief Procedure when you stop

dispensing and before cleaning, checking,

or servicing the equipment.

FIG. 1

Service

83A5413F

5. Replace cover (5) and screws (36).

Tighten screws hand tight. Do not

over-tighten screws(FIG. 3).

Bezel Replacement

Pulse Meters use Bezel Replacement Kit

26C287

SDP Meters use Bezel Replacement Kit

26C403

SDM Meters use Bezel Replacement Kit

26C484

NOTE: The metered dispense valve does not

have to be taken out of service to replace the

bezel.

Disassembly

1. Relieve pressure. See Pressure Relief

procedure, page 7.

2. Remove batteries. See Battery

Replacement, page 7.

3. Remove 4 screws (21) and o-rings (20)

and carefully lift bezel (19) off housing

(12) (FIG. 4).

NOTE: The solenoid (Pulse and SDP

Models only) and power will still be

connected to the bezel via the power

connections as shown in FIG. 5. Before

the bezel can be completely separated

from the housing, these connections

must be detached.

FIG. 2

FIG. 3

Service

3A5413F 9

4. Detach the red and white solenoid

connection (a) (FIG. 5).Pulse and SDP

Models only.

5. Detach the black and red power

connection (b) (FIG. 5).

NOTE: Be careful not to disturb the white

button board ribbon cable taped to the

bezel housing if reusing the bezel (19).

Reassembly

1. Connect the black and red power wires

(b) (FIG. 5).

NOTE: Be careful not to disturb the white

button board ribbon cable taped to the

bezel housing.

2. Connect red and white solenoid wires (a)

(FIG. 5).Pulse and SDP Models only.

3. There are three wire groupings that must

be carefully routed inside the housing.

•Wrap the red and white solenoid wire (a)

around the solenoid (37) (FIG. 6). Pulse

and SDP Models only.

•Route the red and black power wires (b)

between the central valve boss (c) and

the battery compartment (d) and under

the foam retainer (FIG. 7).

FIG. 4

FIG. 5

FIG. 6

Service

10 3A5413F

•Route black and white wire (f) between

the central valve boss (c) and gear cover

screws (e) (FIG. 8).

NOTE: This wire runs between the two

battery compartments.

FIG. 9 shows the inside of the housing with all

wires routed correctly.

4. Take care that the wires will not be

pinched between the bezel (19) and

housing (12) and between the green

printed circuit board and the gear cover

when securing the bezel to the housing.

5. Verify o-ring (20) is in place on housing

(12). Install bezel (19) to housing using

o-rings (20) and 4 screws (21). Tighten

screws securely.

6. Install batteries and battery cover. See

Battery Replacement, page 7.

7. Recalibrate the metered dispense valve.

See Calibrate the Metered Dispense

Valve instructions provided in the

appropriate Metered Dispense Valve

Installation and Operation manual.

8. Pulse Pro meters must be registered and

configured per instructions found in

PulseTM Metered Dispense Valve

manual.

SDP meters with Pulse FC enabled must

be configured per instructions found in

SDP8/SDP18 Preset Metered Dispense

Valve, Pulse FC Enabled manual.

FIG. 7

FIG. 8

FIG. 9

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Unité de contrôle

Graco

Graco Series E Manuel d'utilisation

Graco

Graco ProGuard+ Manuel utilisateur

Graco

Graco SaniForce 25D009 Manuel de la liste des pièces

Graco

Graco 256653 Manuel utilisateur

Graco

Graco Dispensit 1092 Guide de dépannage

Graco

Graco 246085 Mode d’emploi

Graco

Graco PD44 Guide de dépannage

Graco

Graco 239850 Manuel d'utilisation

Graco

Graco 26D274 Manuel utilisateur

Graco

Graco 25V482 Manuel utilisateur

Graco

Graco CleanShot 244160 Manuel de la liste des pièces

Graco

Graco CSP Series Manuel utilisateur

Graco

Graco 255751 Manuel utilisateur

Graco

Graco Dyna-Star 77X540 Manuel utilisateur

Graco

Graco 1093 Instruction manuelle

Graco

Graco PD44 Instruction manuelle

Graco

Graco Advanjet 26B970 Instruction manuelle

Graco

Graco Gun Flush Box 570046 Manuel d'utilisation

Graco

Graco Dispensit-710 Manuel utilisateur

Graco

Graco 24W870 Manuel

Graco

Graco PD44 Instruction manuelle

Graco

Graco 482 Series Manuel d'utilisation

Graco

Graco SDP8 Series Manuel du propriétaire

Graco

Graco SERIES F Manuel d'utilisation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

Flyron

Flyron FN-BC04 Manuel utilisateur