Goelst 6045 Series Manuel utilisateur
Manual RF operation
Transmitter series
6045
EN
Required:
Goelst built-in
RF receiver
Motor art no’s:
GM-xxx-xxx1
GMT-xxx-xxx1
For G-Motion
2
English
3
Contents
1. RF controls .......................................................5
1.1 Products .................................................................................. 5
1.2 Button layout............................................................................ 6
2. First use...........................................................7
2.1 Auto calibration and RF channels ............................................... 7
3. Programming.....................................................9
3.1 Programming G-Motion motor units ............................................ 9
3.2 Overview Programming menus ..................................................10
3.3 Programming options ...............................................................11
MENU 1
1.1 Set end positions .............................................................................11
1.2 Set RF channels...............................................................................12
MENU 2
2.1 Opening and Closing Speed ............................................................13
2.2 Intermediate positions.....................................................................13
2.3 Light sensor......................................................................................14
2.3.1 Sun light settings ............................................................................................15
2.3.2 Dawn/Dusk light settings .................................................................................16
2.3.3 Light Sensor behaviour.....................................................................................17
2.4 CPS: Curtain Protection System......................................................18
2.4.1 Touch and Go....................................................................................................18
2.4.2 Touch and Stop.................................................................................................19
MENU 3
3.1 Operation mode ...............................................................................21
3.2 Inverted input ...................................................................................22
3.3 Timer ........................................................................................ 23
3.4 - 3.6 (Reserved)................................................................................24
3.7 Factory settings.................................................................................25
TOC
English
5
1
6045-ERA-P1
6045-ERA-W1
6045-KRONO-6WW
6045-CORE
6045-ERA-P6
6045-ERA-W6
6045-ERA-P18
RF controls
1. RF controls
1.1 Products
Goelst G-Motion motor units offer a wide range of features for optimal use in many situa-
tions. Feature settings can be changed and stored by means of the buttons on the motor
unit itself or other controllers, e.g. the RF transmitter.
Hand transmitters
1, 6 or 18 channels
Wall transmitters
1 or 6 channels
Timer
6 channels
Wi-Gateway
Control via the
MyNice Welcome App
English
6
1RF controls
1.2 Button layout
The RF transmitter series 6045 can be used for operating and programming G-Motion motor
units. During programming the STOP and OPEN/CLOSE are mainly used and optionally the
PRG off ESC buttons on the back of the controls.
Button timings:
- “Shortly press the button(s)” = keep pressed less than 1 second.
- “Press and hold the button(s)” = keep pressed for more than 1 second.
Example of the 6 channel handheld RF transmitter:
For the timer module: refer to manufacturers manual.
Additional programming buttons on the back of the Remote Controls:
Briey press ■ STOP (front side) to exit programming mode or wait 15 sec.
▲▼ OPEN / CLOSE
During curtain control:
send an open or close signal on selected channel
During programming:
Cycle through menu options.
ESC
Cycle through main menus and menu options.
■ STOP
During curtain control:
stop curtains at current position
During programming:
choose a menu or conrm a selection
PRG
to main menus or to conrm a selection
English
7
2
6002
6002
art. 6048-1001-03
First use
2.1 Auto calibration and RF channels
G-Motion motor units wil auto calibrate for end positions on rst use.
Auto-calibration can be started with the buttons at the bottom of the motor. Or with the RF-
remote control, but then rst an RF-channel has to be programmed in the motor. After auto
calibration, the system is ready for use and responds to the set RF channel.
Auto calibration available on motor types GM-4xx and GM-6xx ( NOT on GM-1xx )
1. Place the motor unit onto the curtain rail system (see G-Motion manual).
2. Place the curtains if possible and then adjust internal
endstop(s) if necessary for improved curtain pleating.
(art. 6002, Allen key 2). These stops are pre-secured
and limit the running distance of the pilot carrier. During
the auto calibration cycle below, electronically dened
‘soft stops’ will be set with the 6002 stops as refer-
ence.
3. Connect an active power source (type depends on motor unit type).
4. To set up a rst RF channel
and
preform auto-calibration: start at step 1, for auto-
calibration only with already set RF channels: start at step 2.
STEP 1: Set up rst RF channel
Adding RF channels when no RF channel has been programmed yet.
(This method can also be used to add additional channels later on)
Note: After 15s. without input, the motor unit quits programming mode.
Please rst read each step for this feature,
1. Press and hold the OPEN+CLOSE motor buttons, until
the LED on the motor unit turns white (~4s.).
2. Repeatedly press OPEN or CLOSE motor buttons until
the LED is yellow.
3. Shortly press both OPEN+CLOSE motor buttons to
enter the feature menu
4. The LED on the motor unit now ashes yellow.
5. A Activate a channel To activate a RF channel, shortly press the OPEN button of the
desired channel on the RF transmitter. The LED on the motor unit responds with a
short continued green signal and then starts ashing again. If desired, add more
channels one by one to this motor unit, via OPEN buttons of corresponding RF chan-
nels (max. 16 channels).
motor LED colour yellow:
2. First use
English
8
2First use
5. B De-activate a channel To de-activate a RF channel, shortly press the CLOSE button
of that channel on the RF transmitter. The LED on the motor unit responds with a
short continued red signal and then starts ashing again. If desired, de-activate
more channels one by one to this motor unit, via CLOSE buttons of corresponding
RF channels.
5a and 5B can be used in random order
6. Conrm and save the setting by briey pressing STOP of a channel (just) programmed.
7. The LED on the motor unit is white again for 15 seconds.
8. Wait for 15 seconds or shortly press STOP of a channel (just) programmed to quit
programming.
The LED on the motor unit switches off, proceed to step 2 to start auto-calibration.
STEP 2: Auto-calibration.
1. Briey press one of the motor buttons or those on the RF transmitter.
2. The LED on the motor unit now ashes red.
3. The system will run until it is stopped by the internal end stop.
4. The system will move ~1cm in opposite direction and then waits for 5 seconds:
within 5 seconds start ne tuning this end position if necessary, by using the motor
buttons or OPEN or CLOSE on the RF transmitter.
5. After 5 seconds without signal, the calibration cycle continues. The system now
runs in opposite direction until it is stopped by the internal end stop.
6. The system will move ~5cms and then waits for 5 seconds: within 5 seconds start
ne tuning this end position if necessary, using the motor buttons or OPEN or CLOSE
on the RF transmitter.
7. After 5 seconds without signal, the system will move 20cm in Open direction.This
completes calibration and the red LED on the motor unit switches off. CPS mode is
switched on automatically. The system is now ready for use..
Auto-calibration can be interrupted by pressing one of the buttons.
English
9
3
Programming
3.1 Programming G-Motion motor units
Goelst G-Motion motor units offer a wide range of features for opti-
mal use in many situations. Feature settings can be changed and
stored using the buttons on the motor unit itself or the RF transmit-
ter.
Programming is done with aid of visual feedback from the multicolor
LED in the motor unit.
Each programming feature is represented by 1 colour, for example
the feature ‘setting end positions’, shows a red LED.
Feedback also consists of blinking patterns to identify the selected
feature setting. See § 3.2 on p. 10 for an overview of the 3 main
menus and all available features.
In the event of a power cut, the RF channels will remain stored in the motor unit.
3. Programming
English
10
3Programming
3.2 Overview Programming menus
LED mode LED colour
Menu 1
continuously
on
White
1.1 End positions Red
1.2 Set infrared Channels (IR) Green
1.3 *) RF Yellow
(reserved)
LED mode LED colour
Menu 2
blinks slowly
White
2.1 Speed Red
2.2 IntermediatePos. Green
2.3 Light sensor
2.3.1 Sun sensor Yellow
2.3.2 Dawn/Dusk sensor Blue
2.3.3 Sensor mode Purple
2.4 CPS
2.4.1 Touch and Go Orange
2.4.2 Touch and Stop Light blue
LED mode LED colour
Menu 3
blinks fast
White
3.1 Control mode Red
3.2 CW/CCW Inverted input Green
3.3 Timer Yellow
(reserved)
3.7 Factory settings Light blue
*)
Option only visible in motor units equipped with RF functionality.
English
Ce manuel convient aux modèles suivants
7
Table des matières
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
