GE PanaFlow HT Manuel utilisateur

PanaFlow HT

Quick Start Guide

Measurement & Control

916-129 Rev. A

September 2012

1. Thank you. Thank you for purchasing the

PanaFlow HT ultrasonic owmeter. Before removing

the PanaFlow HT system from the crate, please inspect

the owmeter. Each instrument manufactured by GE

Measurement & Control is warranted to be free from

defects in material and workmanship. Before discarding

any of the packing materials, account for all components

and documentation listed on the packing slip.

2. Meter Installation. The ideal site is a straight section

of process pipe that meets the following criteria:

• Pipe section is horizontal and above ground.

• Pipe section can accommodate the overall length of the

owcell.

• There is sufcient clearance for the transducers on

the sides of the meter (at the 3 o’clock and 9 o’clock

positions).

• There are at least 10 pipe diameters of straight,

undisturbed ow upstream and 5 pipe diameters

of straight, undisturbed ow downstream from the

transducers.(See User’s Manual.)

• For remote-mounted electronics, the electronics

console should be located within 100 feet (30

meters) from the meter body. (See User’s Manual.)

5. Communication and Power Wiring. The picture below

shows the communication and power wiring to XMT900

electronics. Make all communication wiring before wiring

the power terminals.

Once all wiring is complete, apply the power.

6. Programming & Testing.

The keypad and magnetic wand enable

programming of the instrument through the glass

faceplate without removing the cover. Thus, all

programming procedures may be performed while

the unit is installed in a hazardous area. See the

User’s Manual for instructions on programming.

PIN Label

Description

A-

Analog Output A:4-20mA/HART Output(SIL) Negative

A+

Analog Output A:4-20mA/HART Output(SIL) Positive

B-

Analog Output B:4-20mA Negative

B+

Analog Output B:4-20mA Positive

C-

Digital Output C Negative

C+

Digital Output C Positive

D-

Digital Output D Negative

D+

Digital Output D Positive

Terminal Block - Power Connection(AC)

PIN Label

Description

L2/N

Neutral Connection

Live Power Connection

Terminal Block -Modbus/Calibration Connections

PIN Label

Description

MOD-

Modbus/Service Port Negative

MOD+

Modbus/Service Port Positive

CAL-

Calibration Port Negative

CAL+

Calibration Port Positive

WARNING! The PanaFlow HT ow transmitter can measure the ow rate of many uids, some

potentially hazardous. Be sure to follow local safety codes and regulations for installing electrical

equipment and working with hazardous uids or ow conditions.

3. Remote Electronics Mounting (remote mount

only). If you have a remote mounted XMT900

electronics, mount the XMT900 electronics to either

a wall or to a 2” pipe system using the enclosed

mounting system. If you have a local mount, go to

step 5.

4. Remote Transducer Wiring (remote mount

only). To make electrical connections, remove the

terminal board from the enclosure by rst loosening

the screws and twisting the terminal board counter

clockwise. Feed each cable through a conduit hole on

the side of the enclosure and plug into the appropriate

connection on the terminal board.

7. Final Steps. Complete the SIL requirements and

the Safety Instrumented System (SIS) and PanaFlow HT

User’s Manual for exact details.

8. If you have any questions about your equipment,

please contact us at:

Telephone: +1 978 437 1000

E-mail: [email protected]

Address: 1100 Technology Drive

Billerica, MA 01821-4111

http://www.ge-mcs.com/en/contact-us.html

Measurement & Control Flow

917-025 Rev. A

January 2012

PanaFlow HT

Ultrasonic Liquid Flowmeter

Safety Manual for SIS

names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not aliated with GE.

www.ge-mcs.com

916-129A

Autres manuels pour PanaFlow HT

Autres manuels GE Instrument de mesure

GE Hydran M2-X Manuel utilisateur

GE DewPro MMY 245 Manuel utilisateur

GE Druck DPI 705 Manuel utilisateur

GE RSDetection RS-S131-200-ER0000 Manuel utilisateur

GE DB-16 Manuel utilisateur

GE JXSOUSV1 Manuel utilisateur

GE EPM6000 Manuel utilisateur

GE Moisture Target Series 6 Manuel utilisateur

GE DMS Go Manuel utilisateur

GE RHM 100 Manuel utilisateur

GE Precision 500D Manuel utilisateur

GE Bently Nevada 3300/16 Manuel utilisateur

GE WiMAX WX-I210+c Guide d'installation

GE Aquant Manuel utilisateur

GE Ultrasonic USM Go Manuel utilisateur

GE DigitalFlow GC868 Manuel du propriétaire

GE RHM 30 Manuel utilisateur

GE CheckPoint Manuel utilisateur

GE Centricity SP1001 Manuel utilisateur

GE DM5E Manuel utilisateur

GE CB Watch 3 Manuel utilisateur

GE PACE 1000 Mode d’emploi

GE N60 Manuel utilisateur

GE Protimeter MMS Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur