GarrettCom 4K-Series Manuel utilisateur

www GarrettCom com

Corporate Headquarters

GarrettCom, Inc.

213 Hammond Avenue

Fremont, CA 94539

Phone: 510.438.9071

Fax: 510.438.9072

Web: http://www.GarrettCom.com

Email: [email protected]

Magnum 4K-Series

4K8 Switches

Installation and User Guide

$5.00 USD

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

Magnum



4K-Series

4K8 Switches

Installation and User Guide

Part #: 84-000080 Rev. D

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a

registered trademark of GarrettCom, Inc.

Important: Magnum 4K-Series Fiber Switches contain no user serviceable

parts. Attempted service by unauthorized personnel shall render any and all

warranties null and void. If problems are experienced with a Magnum 4K8

Switches, consult Section 6, Troubleshooting, of this User Guide.

be reproduced without prior written permission from GarrettCom, Inc.

Printed in the United States of America.

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

Contacting GarrettCom, Inc.

Please use the following mailing address, phone and fax numbers or Internet address.

GarrettCom, Inc.

47823 Westinghouse Drive

Fremont, CA 94539

Phone: 510.438.9071

Fax: 510.438.9072

Web: http://www.GarrettCom.com

Email: [email protected]om

Federal Communications Commission

Radio Frequency Interference Statement

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference in a residential installation. This equipment generates, uses, and can

radiate frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interfernce to radio communications. However, there

is no guarantee that interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into n outlet on a ccircuit different from that ot

which the receiver is connected.

- Consult the dealer or an experienced radio TV technician for help.

Canadian Emission

This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil respecte toutes les exigences du R

glement sur le mat

riel du

Canada. Cet appareil est Classe B.

Magnum 4K8 Switches Installation and User Guide (10/04)

iii

www GarrettCom com

TABLE OF CONTENTS Page

1.0 SPECIFICATIONS ............................................................................... 1

1.1 Technical Specifications...................................................................... 1

1.2 Ordering Information........................................................................... 3

2.0 INTRODUCTION ................................................................................. 4

2.1 Inspecting the Package and Product .................................................... 4

2.2 Product Description - Magnum 4K8 Switches .................................... 5

2.2.1 Magnum 4K8 Switch chassis.............................................................. 5

2.2.2: Magnum 4K8R “Reverse” model, front LEDs and connections in

rear............................................................................................................... 6

2.2.3 Fiber-port modules, 100Mb fiber....................................................... 7

2.2.4 Fiber-port modules, 10 Mb fiber........................................................ 8

2.2.5 10/100 Dual-speed Switched ports, RJ-45 (copper) .................... 8

2.2.6 Frame Buffering and Latency...................................................... 9

2.3 Features and Benefits......................................................................... 11

2.4 Applications....................................................................................... 12

3.0 INSTALLATION: ..................................................................................... 14

3.1 Locating Magnum 4K8 Switches....................................................... 14

3.2 Connecting Ethernet Media ............................................................... 15

3.2.1 Connecting Fiber Optic ST-type, “twist-lock”.......................... 15

3.2.2 Connecting Fiber Optic SC-type, "Snap-In".............................. 16

3.2.3 Connecting Single-Mode Fiber Optic........................................ 16

3.2.4 Connecting Twisted Pair (RJ-45,CAT3, CAT5......................... 16

3.3 Rack-mounting ................................................................................... 17

3.4 Fiber Port Module (FPM) Installation ............................................... 18

3.4.1 Preparation for Installing and Removing FPMs......................... 18

3.4.2 Installing FPM Cards in the Magnum 4K8 Switches................. 20

3.5 Powering the Magnum 4K8 Switch................................................... 22

4.0 OPERATION....................................................................................... 23

4.1 Switching Functionality..................................................................... 23

4.2 Status LEDs ....................................................................................... 24

4.3 Manual Switches for Up-link push-button, for RJ-45 Port#1 only.... 24

4.4 Manual Switches “F-H”, for FPM Port#9 only.................................. 24

4.5 Auto-negotiation, for Fast Ethernet copper ports............................... 24

4.6 Auto-negotiation for 10/100Mb ports,............................................... 26

4.7 Flow-control, IEEE 802.3x standard ................................................. 26

4.8 Power Budget Calculations for 4K-Series FPM’s with Fiber Media. 27

5.0 INTRO - MAGNUM 4K8 FIBER-PORT MODULES (FPM)......... 28

5.1 Inspecting the Package and Product (Optional)................................. 28

5.2 Product Description ........................................................................... 28

5.2.1 FPM-MST,100Mbps multi-mode FX-ST-type, “twist-lock”..... 29

5.2.1a FPM10-MST,10 Mbps multi-mode FL-ST-type, “twist-lock” .. 29

5.2.2 FPM-MSC100Mbps multi-mode FX-SC-type, “snap-in” ......... 29

5.2.3 FPM-SSC 100Mbps single-mode FX-SC-type, “snap-in”......... 30

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

5.2.4 FPM-MTRJ,100Mb multi-mode FX, MTRJ small-form-factor 30

5.2.5 FPM-MV45, 100Mbps multi-mode FX, VF-45 small-form-factor 31

5.2.6 FPM-Blank................................................................................. 31

6.0 TROUBLESHOOTING...................................................................... 32

6.1 Before Calling for Assistance............................................................ 32

6.2 When Calling for Assistance ............................................................. 33

6.3 Return Material Authorization (RMA) Procedure............................. 33

6.4 Shipping and Packaging Information................................................. 34

APPENDIX A: WARRANTY INFORMATION......................................... 34

APPENDIX B : INTERNAL DC POWER SUPPLY OPTIONS ................ 35

APPENDIX C: INTERNAL DC DUAL-SOURCE POWER OPTION...... 37

Revisions

10/04: minor updates

04/03: Edited Minor change

Rev D 06/02 : Updated Rack-mounting and Appendix B & C with 24VDC and

125VDC Power option.

Rev C 01/02 : Updated Operating Environment Spec.

Rev B 04/01 : Change the company name to GarrettCom, Inc. (Formerly it was

Garrett Communications). There are no changes to the content of the material at

this time

Rev A 12/00 : This revision is the initial release of the 4K8 Switches user

manual.

Magnum Quad-Series Fiber Switches Installation and User Guide (10/04)

www GarrettCom com

The Magnum Line

ETHERNET CONNECTIVITY PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

OVERVIEW

GarrettCom, Inc offers the premium-quality Magnumline of Ethernet LAN

connectivity products with industry-standard functionality and built-in fiber

configurability. Magnum products are designed for use in demanding Carrier Class,

Industrial Grade and OEM applications where reliability is a primary consideration.

6K25 Managed Fiber Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports,

mix-and match. Features SFF fiber for up to 25 fiber ports in a 1U unit.

4K-Series Switches, 100 and 10 Mbps, copper ports with optional fiber port, with

auto-negotiating full switching performance.

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed

and mixed-media types, full switching performance.

“Outdoor” Ethernet Switch, for temperature uncontrolled locations

6 10/100 and 2 100Mb fiber ports, can be connected in strings

Mixed-Media Fiber Hub, 16-port Stackable,10/100 auto-sensing

Dual Speed 8-port and 16-port Stackables, 10/100 auto-sensing

Stackable Hubs, SNMP Optional

10Mb series and 100Mb series, both w/ optional port modules

Personal Switches, 10/100Mb

8 port dual speed, Auto-negotiable with fiber option

Personal Hubs, 100Mb or 10/100Mb

8-port, with two switched ports (1 fiber built in)

Personal Hubs, 10Mb series

8-port + AUI, stackable to 5 high, + optional BNC of fiber port

8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.

Media Converters, 10Mb and 100Mb series

All media combinations, incl. fiber ST, SC, mm., single mode

The “X-line” of configurable MiXed Media products:

Stackable Concentrators, SNMP optional, 13-Ports

Mini-Concentrators, 7 Ports, Repeaters, 2-Ports

Repeater Port Modules (RPMs),6 types for Ethernet media

Bridge Port Modules (BPMs), 4 types, for segment isolation

Transceivers, 10Mb series Mini-Transceivers and Coax Models Oct, 04

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

1.0 SPECIFICATIONS

1.1 Technical Specifications

Performance

Aggregate Filtering Rate: (all ports are wire speed)

1,190,400 frames/sec for 8 100Mbps ports (for Magnum 4K8)

Aggregate Forwarding Rate: (all ports are wire speed)

595,200 frames per second

Data Rate: 10 Mbps and 100Mbps

Address Table Capacity:16K node addresses,self-learning w/address aging

Packet buffer size : 1 MB dynamic

Latency: 5 s + packet time (100 to 100Mbps)

15 s + packet time (10 to 10 Mbps, and 10 to 100Mbps)

Network Standards

Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,

IEEE 802.3u: 100BASE-TX, 100BASE-FX

Maximum 10 Mbps Ethernet Segment Lengths

Unshielded twisted pair - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

10BASE-FL multi-mode fiber optic - 2 km (6,562 ft)

10BASE-FL single-mode fiber optic - 10 km (32,810 ft)

Maximum Standard Fast Ethernet Segment Lengths:

10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft) 100BASE-

FX, half-duplex, multi-mode - 412 m (1350 ft) 100BASE-

FX, full-duplex, multi-mode - 2.0 km (6,562 ft)

100BASE-SX, short wavelength HDX m.m. - 300 m ( 935 ft)

100BASE-FX, half-duplex, single-mode - 412 m (1350 ft)

100BASE-FX, full-duplex, single-mode - 20.0 km (49,215 ft)

100BASE-FX, full-duplex, s.m(Long Reach)- 40.0 km (132,215 ft)

Connectors for copper wiring

Twisted Pair at 10/100Mb:RJ-45 shielded, female, front mounted

(for Magnum K-Series Fast Ethernet copper ports, use Cat 5 cable)

Fiber Multi-mode connector types:

Fiber Port, SC-type (snap-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, ST-type (twist-lock): Fiber optic multi-mode, 100BASE-FX

Fiber Port, MTRJ-type (plug-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, VF-45 type (plug-in): Fiber optic multi-mode, 100BASE-FX

Fiber Port, ST-type (twist-lock):Fiber optic multi-mode, 10BASE-FL

Fiber Single-mode connector types:

Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX

Manual switch-selections and jumpers

Up-link Push-button: Crossover switch for one RJ-45 port#1

F-H: In F Port #9(fiber port)at full 100Mbps and in H at Half-duplex

Fiber default: Full-duplex (Internal jumpers may select HDX mode)

Copper default: Auto-negotiation

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

LEDs: Per Port

LK/Act: Steady ON for Link with no traffic, blinking indicates

port is transmitting and receiving

F/H: ON = Full-Duplex Mode

OFF = Half-Duplex Mode

100/10: ON = 100Mbps speed

OFF = 10 Mbps

Operating Environment

Ambient Temperature: 25to 140F (-5to 60C)

Storage Temperature: 0to 185F (-40to 85C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 13,000ft (-60 to 4000m)

Conformal coating options: Request quote

Packaging

Enclosure: Rugged High strength metal. Suitable for stand-

alone or rack-mounting

Dimensions: 1.75 in H x 17.0 in W x 9.0 in D

4.45cm H x 43.2cm W x 22.9cm D

Weight: 3.2 lb. (1.4 Kg) rack-mount models

Cooling method: Fan cooled, @ 9 cfm

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis, with

adjacent manual ON-OFF switch (on AC models only)

Input Voltage: 110 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 9 watts typical, 11 watts max.

Power Supply Rating: 3Amps at 5VDC

DC Power Supply (Options)

-48VDC Power Input Voltage : 36 to 72 VDC

24VDC Power Input Voltage : 20 to 36VDC

125VDC Power Input Voltage : 120 to 160VDC

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

For Dual Source and Redundant DC for –48VDC, 24VDC &

125VDC supply options (Optional), see Appendices

Mechanical

Enclosure : Rugged high strength sheet metal. Suitable for stand-alone or

1U rack mounting.

Rack-mounting brackets: 19” included; ETSI and 23” Telco optional.

Agency Approvals

UL listed (UL1950), cUL, CE

Emissions meet FCC Part 15 Class B

Optional: ETSI and NEBS L3 Certified

Warranty Three years, return to factory Made in USA

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

1.2 Ordering Information

Magnum 4K8 Switches

MODEL DESCRIPTION

Magnum 4K8 Ethernet Switch with 8 RJ-45 ports, each auto-sensing for

10Mbps/10Mbps FDX/HDX operation. Optional fiber port

may be configured from the family of modules below.

Each port is switched and provides a full-speed traffic

domain with non-blocking performance. Includes internal

auto-ranging power supply, cooling fan, and metal brackets

for rack-mounting. LEDs and user ports are in the front,

power inputs is in the rear. Units with -48V power supply

options available

Magnum 4K8R “Reverse” model, Same as Model 4K8 Switch except user

ports and the power input connectors are in the rear.

Fiber Port Modules for Magnum 4K-Series(4K8 Switches only)

FPM-MSC Fiber module for 4K8 Switches, with 100Mbps multi-mode

FX SC connectors

FPM-MST Fiber module for 4K8 Switches, with 100Mbps multi-

mode FX ST connectors

FPM-SSC Fiber module for 4K8 Switches, with 100Mbps single-

mode FX SC connectors

FPM-MV45 Fiber module for 4K8 Switches, with 100Mbps multi-

mode FX “VF-45” connectors

FPM-MTRJ Fiber module for 4K8 Switches, with 100Mbps multi-

mode FX “MTRJ” connectors

K8PM-RJ45 RJ-45 module for 4K8 Switches, with 100Mbps fixed RJ-

45 ports, full or half-duplex

FPM10-MST Fiber module for 4K8 Switches, with 10 Mbps multi-mode

FL ST-type connectors

FPM-BLNK Blank face plate, included in 4K8 switch unit when no fiber

port option is selected

See appendices B and C for information on DC-powered models and options.

GarrettCom, Inc. reserves the right to change specifications, performance

characteristics and/or model offerings without notice.

Magnum 4K8 Switches Installation and User Guide (10/04)

www GarrettCom com

2.0 Introduction

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage that you believe occurred during shipment or

delivery. Inspect the contents of this package for any signs of damage and ensure that

the items listed below are included.

This package should contain:

1 Magnum 4K8 Switches

1 AC Power Cord (U.S. and other 115 VAC only)

1 Set of metal “Ears” for rack mounting

1 Installation and User Guide (this manual)

1 Product Registration Card

Remove the items from the shipping container. Be sure to keep the shipping

container should you need to re-ship the unit at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to

GarrettCom, Inc as soon as possible.

In the event there are items missing or damaged, contact the party from whom

you purchased the product. If the unit needs to be returned, please use the original

shipping container if possible. Refer to Section 6, Troubleshooting, for specific return

procedures.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GarrettCom Changer

GarrettCom

GarrettCom Magnum PS14P Manuel utilisateur

GarrettCom

GarrettCom Magnum 6KQ Manuel utilisateur

GarrettCom

GarrettCom Magnum 6K8-Series Manuel utilisateur

GarrettCom

GarrettCom Magnum 4K220 Manuel utilisateur

GarrettCom

GarrettCom PS14H-48VDC Manuel utilisateur

GarrettCom

GarrettCom MAGNUM 6KM Manuel utilisateur

GarrettCom

GarrettCom Magnum CSG14 Manuel utilisateur

GarrettCom

GarrettCom MAGNUM H80B Manuel utilisateur

GarrettCom

GarrettCom Magnum ST80 Stackable Manuel utilisateur

GarrettCom

GarrettCom Magnum 6K32T Manuel utilisateur

GarrettCom

GarrettCom MAGNUM MAGNUM 6KM Manuel utilisateur

GarrettCom

GarrettCom Magnum DS 880 Manuel utilisateur

GarrettCom

GarrettCom Quad Manuel utilisateur

GarrettCom

GarrettCom DS60s Manuel utilisateur

GarrettCom

GarrettCom Magnum 6K16-Series Manuel utilisateur

GarrettCom

GarrettCom DS8016 Manuel utilisateur

GarrettCom

GarrettCom Magnum 8000X Manuel utilisateur

GarrettCom

GarrettCom Magnum 14E Manuel utilisateur

GarrettCom

GarrettCom Magnum 1016 Manuel utilisateur

GarrettCom

GarrettCom Magnum 6K25e Manuel utilisateur

GarrettCom

GarrettCom Magnum 6KQE Manuel utilisateur

GarrettCom

GarrettCom Magnum CS14 Series Manuel utilisateur

GarrettCom

GarrettCom 500-Series Manuel utilisateur

GarrettCom

GarrettCom Magnum CSG14 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur