FuzzDog Flender Manuel utilisateur

Flender

Crazy, intense fuzz with blend

control to keep things sane

PedalParts.co.uk

Schematic

BOM

R1 15K

R2 150K

R3 560K

R4 47K

R5 1K5

R6 120K

R7 10K

R8 680R

R9 220K

R10 150K

R11 8K2

R12 8K2

R13 27K

R14 27K

R15 100K

R16 10K

R17 820R

R18 27K

R19 3K9

R20 10K

R21 100K

R22 18K

R23 150K

R24 47K

R25 820R

R26 10K

R27 3K9

R28 2K2 (CLR)

R29 2K2 (CLR)

C1 100n

C2 47n

C3 100n

C4 10u elec

C5 10u elec

C6 10u elec

C7 10u elec

C8 10u elec

C9 10u elec

C10 100n

C11 3n3

C12 10u elec

C13 1n

C14 10u elec

C15 10u elec

C16 100u elec

C17 100n

1-5 2N5088*

D1 1N4001

D2-5 1N34A

BLEND 100KB

SUSTAIN 10KA

TONE 20KB

LEVEL 50KA

SW1-2 3PDT FOOTSW.

Main schematic shows all the switch

connections and the pads to build the

two different tone boost configurations,

which are shown above. More later...

*Other transistors can be used.

TONE BOOST CONFIGURATIONS

ORIGINAL REISSUE

FOOTSWITCHES

ake sure you orientate them with the

tags horizontally as shown. Its a good

idea to put the them

in place in the

enclosure and

loosely tighten

them, then place the

PCB on top to get

the position right

before soldering.

Snap the little metal tag off the pots to mount them flush in the box.

You UST use some kind of heat sink on the legs of the diodes and the transistors when

soldering. They aren’t keen on heat. Any more than 3-4 seconds of iron and they’re toast.

ALL the components mount on the top side of the board.

It’s a good idea to run the pot wires from the back of the PCB

(opposite side to the components) in order to ensure plenty of

clearance for the jack sockets when assembling. ake sure you give

yourself plenty of length on the wires so assembly isn’t tight.

The pads marked in RED above are to select your Tone Boost

configuration. You could add header pins and use jumpers to select

between them, but its easy enough to just use jumper wires.

Honestly, the Reissue configuration sucks - there’s a big volume drop.

Just go with the original.

ORIGINAL REISSUE

1 2 3

LEDs

Leave these out until you’re

boxing it all up - see later.

WIRING FOR TESTING

Connect everything up but the LEDs. That includes the footswitches.

Ensure your power supply is 9V Tip Negative, or connect up a battery for

now. If connecting a battery, solder long lengths of wire to the +V and GND

pads on the PCB, then attach the battery to the other end of these. This

saves desolding stuff from the board, which is a pain.

JACK SOCKETS DC SOCKET

GND

SIGNAL

Ignore the third tag

- you only need that

if wiring up for

battery.

SIGNAL is JACK IN and

JACK OUT on the PCB.

Each socket has its own

GND connection

conveniently placed.

Plug in. Go!

If it works, crack on and get it in the box. If not, troubleshoot. Check you

have everything in the right place and reflow any poor joints.

BOXING UP

There’s plenty of space in there, but you may need to turn the jack sockets

one way or the other to ensure you clear the PCB.

Turn your pots as shown to clear the jack sockets.

What about my LEDs?

Pre-drilled enclosures are supplied with 3mm holes for the LEDs, rather than

larger ones that require a mounting bezel. Why? Because you can hold the LED

securely in place with the PCB. When you come to box up your lovely new circuit,

get the pots in place first. Then the jacks. Now, slide your LEDs all the way into

the PCB (short leg to square pad) and bend the legs ever so slightly so they don’t

fall out. Alternatively put a little bluetac on there. Now locate your footswitches

into place and tighten.

When everything is secure, let your LEDs slide down into the holes - use some

needle-nosed pliers or skinny fingers to position them fully in the holes. I won’t

kid you, its a little fiddly but worth it for the neat finish you’ll get.

No bezel = happy pedal.

Once in place, solder. Those little lights aren’t going anywhere!

Hang on - there’s an extra pad next to the Tone Boost LED. Yes - you can use a

common-cathode tri-colour LED if you like, to show a different colour depending

on selection, rather than the standard on-off with a normal LED.

Please check positioning before drilling - those holes are your responsibility

and these templates are just a guide. Pots are spaced 27mm.

Recommended drill sizes:

Footswitch, DC 12mm or 13mm with wiggle room

Jack sockets 9.5-10mm

Pots 7mm

PedalParts.co.uk

Drilling template - 1590B

Table des matières

Autres manuels FuzzDog Pédale musicale

FuzzDog

FuzzDog Hot Snake Boost Manuel utilisateur

FuzzDog

FuzzDog BSIAB2 Manuel utilisateur

FuzzDog

FuzzDog BrassBlender Manuel utilisateur

FuzzDog

FuzzDog Repeater V4 Manuel utilisateur

FuzzDog

FuzzDog DeathDrive Manuel utilisateur

FuzzDog

FuzzDog SweetyPuss Manuel utilisateur

FuzzDog

FuzzDog Rodent Manuel utilisateur

FuzzDog

FuzzDog 7 of Dwarves Auto Wah Manuel utilisateur

FuzzDog

FuzzDog Mutant Fuzz Manuel utilisateur

FuzzDog

FuzzDog Animatron Manuel utilisateur

FuzzDog

FuzzDog Electrica+ Manuel utilisateur

FuzzDog

FuzzDog Clay Jones OD V2 Manuel utilisateur

FuzzDog

FuzzDog Filth Fack! Manuel utilisateur

FuzzDog

FuzzDog Bionic GuzzFun Manuel utilisateur

FuzzDog

FuzzDog Jordan Bosstone Manuel utilisateur

FuzzDog

FuzzDog KlonBuffer V3 Manuel utilisateur

FuzzDog

FuzzDog FY2 Manuel utilisateur

FuzzDog

FuzzDog Ruby/NoisyCricket Manuel utilisateur

FuzzDog

FuzzDog Candyman Manuel utilisateur

FuzzDog

FuzzDog Super Fuzz Manuel utilisateur

FuzzDog

FuzzDog Ultimatum Fuzz Manuel utilisateur

FuzzDog

FuzzDog Tube Screamer v4.0 Manuel utilisateur

FuzzDog

FuzzDog The Gimp Manuel utilisateur

FuzzDog

FuzzDog Klone V4 Manuel utilisateur

Manuels Pédale musicale populaires d'autres marques

Behringer

Behringer ULTRA WAH UW300 Manuel utilisateur

Whirlwind

Whirlwind oc-bass Manuel utilisateur

Strymon

Strymon Lex-rotary Manuel utilisateur

Behringer

Behringer PB600 Manuel utilisateur

Lexicon

Lexicon MX200 Manuel utilisateur

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manuel utilisateur

Matthews Effects

Matthews Effects Whaler V2 Manuel utilisateur

Grid 1

Grid 1 Pedal Jeanie Manuel utilisateur

Amptweaker

Amptweaker tightboost Manuel utilisateur

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manuel utilisateur

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manuel utilisateur

BYOC

BYOC Analog Chorus Manuel

Dimavery

Dimavery EPVP-50 Manuel utilisateur

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manuel utilisateur

Pro-MIDI

Pro-MIDI G25 Manuel utilisateur

DW 7000 Manuel utilisateur

FAMC

FAMC Liquid-Foot Jr. Series Manuel utilisateur

Dimavery

Dimavery EPOD-50 Overdrive Manuel utilisateur