Futech QUATTRO Manuel utilisateur

QUATTRO

150.40.A

MANUAL

26 27 28 29 30 31

1. Magnet

2. LED indicator (orange)

3. LED indicator (green)

4. LED indicator (red)

5. Laser-sensitive area

6. Marking notch

7. Clamp

8. On/Off

9. Volume / Operating mode

10. Accuracy / LED activation

11. Bubble vial

12. Display

13. Type plate with serial number

14. Fixing thread for the clamp

15. Beeper

16. Battery door and latch

Display

17. “Rotary laser” mode

18. “Line laser” mode

19. Beeper Volume High

20. Beeper Volume Low

21. Beeper Volume Off

22. Battery Low

23. Battery OK

24. Accuracy: Coarse, 3mm

25. Accuracy: Medium, 2mm

26. Accuracy: Fine, 1mm

27. Much too low / Fast interval tone

28. Too Low / Fast interval tone

29. On-grade / Continuous tone

30. Too high / Slow interval tone

31. Much too high / Slow interval tone

32. No laser / No tone

QUATTRO

MANUAL

Depending on the selected operating

mode, the receiver detects either the

laser beams (red and green) of rotating

lasers or the (horizontal or vertical) laser

lines of line lasers with hand-held re-

ceiver function. Any other use than the

described above shall be deemed to be

improper use.

First use

Avoid violent shocks or dropping the

unit.

Inserting / changing the battery

Change tha battery if the batterysym-

bol (22) is displayed.

Open the battery cover (16)

Remove tha battery and insert a new

one (observe correct polarity)

Dispose ofthe used battery (see chap-

ter on environmental protection)

Operating

Switching the device on / off

Press the On / Off button (8)

Adjusting the volume

-

cessary repeated

switches the beeper volume between

High / Low / Off

Selecting the operating mode

Press the volume button (9) for at least

3 seconds.

switches from rotating laser to line la-

ser and vica versa

Adjusting the accuracy



necessary repeated

switches the accuracy of readings be-

tween Coarse / Medium / Fine

Activating / Deactivating the LEDs

Press the accuracy-button (10) for at

least 3 seconds.

Operating

Hold the device vertically (in case of a

vertical laser plane: horizontally) and

move it to the laserplane.

Please pay attention to the acoustic

signals and arrows on the (LED) dis-

play.

NOTE

When the device is switched on, it is

in the operating mode used before it

was switched off.

If in line laser mode, the device de-

tects only the line laser type which was

rst detected after the power on.

Maintenance and Care

Keep the device always clean, especi-

ally the laser-sensitive area!

Do not use aggressive cleaning

agents or solvents.

If soiled heavily the device can be cle-

anedunder running water.

Do not use high-pressure cleaner.

Allow it to dry completely before sto-

ring it in a closed container. Residual

moisture can result in corrosion of the

battery contacts. In this case our war-

ranty expires.

In the unlikely event of a failure or

defect, have the appliance examined

and repaired by Futech.

In all your queries and spare part or-

ders, always quote the serialnumber

(see type plate) of your device.

DECLARATION OF CONFORMITY

We herewith declare that this product conforms with the following standards and

directives:

Standards

DIN EN 61000-6-1

DIN EN 61000-6-3

in accordance with the regulations stipulated in the directives:

EC Directive

2004/108/EG

2006/95/EG

Technical changes reserved.

We accept no liability for printing errors.

TECHNICAL SPECIFICATIONS

 

 



 

 

 

 







 

 

 

 

Ce manuel convient aux modèles suivants

Autres manuels Futech Instrument de mesure

Futech

Futech T-BEVEL-30 Manuel utilisateur

Futech

Futech MULTICROSS 3 Super Vision Manuel utilisateur

Futech

Futech DISTY 40R Manuel utilisateur

Futech

Futech MULTICROSS 3D BRAVE Manuel utilisateur

Futech

Futech RED RUNNER Manuel utilisateur

Futech

Futech MULTISCAN 196.20 Manuel utilisateur

Futech

Futech PARA DS Manuel utilisateur

Futech

Futech DISTY60 Manuel utilisateur

Futech

Futech DISTY 120RC Manuel utilisateur

Futech

Futech 150.40.M Manuel utilisateur

Futech

Futech LL6305 Manuel utilisateur

Futech

Futech 031.03 Manuel utilisateur

Futech

Futech Quatro Manuel utilisateur

Futech

Futech MEGACROSS Manuel utilisateur

Futech

Futech TERACROSS Manuel utilisateur

Futech

Futech EAGLE 24 Manuel utilisateur

Futech

Futech WS4300 Manuel utilisateur

Futech

Futech MULTICROSS 3 Manuel utilisateur

Futech

Futech MULTICROSS 3D Manuel utilisateur

Futech

Futech MULTIPOWER 3.6 COMPACT Manuel utilisateur

Futech

Futech DISTY40 Manuel utilisateur

Futech

Futech MULTICROSS 4D ELECTRONIC Manuel utilisateur

Futech

Futech LL4200 Manuel utilisateur

Futech

Futech MULTICROSS 5 SUPER Vision Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur