FUTABA T16IZ Manuel utilisateur

YourFutabaT16IZtransmitterprogrammingcanbeupdatedeasily

online.Whenfunctionsareaddedorimproved,theupdatefile

canbedownloadedfromourwebsite.Copytheupdatefilestothe

microSDcardandthenusethefollowingproceduretoupdatethe

program.CheckourwebsitefortheFAQregardingupdatingformore

information.

HowtoupdateT16IZ

ŸƓƇƄƗƌƑƊŃƓƕƒƆƈƇƘƕƈ

Note: If the battery fully discharges during

program updating, updating will fail. When

the remaining battery capacity is 50% or

less, always recharge the battery before

updating.

Note: The model data in the transmitter can

be used unchanged after updating, but to

be safe, back up the model data before

updating.

1. Download the zip file of the update data

from our website.

([WUDFWWKH]LSÀOHRQ\RXUFRPSXWHU

3. The "FUTABA" folder will be created on your

computer.

4. Copy the "FUTABA" folder into your microSD

card.

Note: If the microSD card has already had

"another FUTABA" folder before you make a

copy, the "FUTABA" folder is OVERWRITTEN.

5. Insert the microSD card with "FUTABA" folder

that contained the update software into the

SD card slot on your T16IZ radio transmitter.

6. Turn on the transmitter power while pressing

down the "HOME/EXIT" button. The update

screen appears on the LCD display of your

T16IZ and the software update is started.

FutabaWEB

16IZUpdateZipﬁle

Download

Copythe"FUTABA"

folderintoyourSDcard.

InstalledmicroSDcard

oftheupdateﬁle

PresstheHOME/EXITswitchandturnon

Updating

7. When the software update is completed,

"Completed" message is shown on the LCD

display of your T16IZ. (Show below picture.)

8. Turn off the power switch of your T16IZ and

remove the microSD card from the card slot.

Possible Problems

When one of the error messages shown

below appears on the LCD screen your

T16IZ, the software update will not be

completed.

"Low battery."

Software update is postponed because

of low battery. Retry the software update

after the battery is recharged.

8SGDWHÀOHQRWIRXQG

The T16IZ cannot find the update file on

the microSD card. Check to be sure all the

update files have been copied onto the

microSD card.

%URNHQÀOH

7KH7,=GHWHFWVWKHXSGDWHÀOHHUURU7KH

update file may be broken or for another

transmitter.

"Write error."

The software update procedure is stopped

for an unknown reason. Contact your local

service center when this error message

appears on the LCD screen of your T16IZ.

Don't absolutely remove the battery

and the microSD card from the

transmitter during the update.

There is a possibility that the transmitter

will be damaged.

Recovering a failed update

If you failed to update for any reason, it

may transmitter will not start.

In that case, please update again

transmitter in the following procedure.

1. Detach the battery from the transmitter.

2. Insert the microSD card that contained

WKHXSGDWHÀOHVWRWKHWUDQVPLWWHU

3. Attach the battery to the transmitter

while pressing down the "HOME/EXIT"

button.

4. The update will start.

Even after the above steps, if the

transmitter fails to update or does not

start, please have it serviced.

Complete

1M23Z07713 T16IZSOFTWAREUPDATECHANGES

V3.3

This software updates or alters the functions and features noted below. The instructions and information that follow are meant as a supplement to the original

instruction manual that accompanied the T16IZ transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with

these instructions. Please check to ensure that the update has been installed.

1) Select the System Menu.

2) Touch the [Information] button.

3) Conﬁrm that the information in the display indicates the version numbers as noted above.

1. CH3 (THR) can be output to the RUD2 / S.BUS2 port.

2. The Holding Power rate of the aircraft in AVCS mode has been expanded to 5 types from C1 to C5, and each rate can be set by switching

the display.

3. Added the setting of switching CH of Holding Power rate C1 to C5 to S.BUS basic menu.

◆ BasicMenuscreen AddedCH3(THR)totheoutput

itemofRUD2/S.BUSport

C1-C5switch

button

Withtheswitchbutton,the

"holdingpower"ofeachrate(C1to

C5)canbedisplayedandadjusted.

Taptothebasicmenu

To"Conﬁg"

To"SBUSBasic"

◆S.BUSBasicscreen The second page has been added, and the total number of pages has changed from 2 to 3.

Additionalpage

HoldingPowerC2toC5

Taptomovetotherate

switchingCHsettingpage.

TaptheCHusedforrateswitching

toselectit.

Thesoftwareversionof

theconnectedGYA553is

displayed.

There are 7 pages in total, and the additional functions

are 1 page and 6 pages.

◆Conﬁgscreen

1. GYA553 New ﬁrmware Version 2.x support. → Refer to T16IZ GYA553 V2 Setting manual

26(1*,1((01HZÀUPZDUH9HUVLRQVXSSRUW

If you have used the EM-100, the update will unregister the EM-100 from the "Sensor" screen. Register the EM-100

again on the "Sensor" screen.

C1 C5

-100% 100%-35% 35%0%

C1 C3 C5C4C2

-100% 100%-25%-75% 75%25%0%

-100%

100%

The current rate numbers C1 to C5 are displayed by operating the channel of the transmitter.

Like the ﬂight condition function of the transmitter, you can set up to 5 different data for the attitude holding force rate of the

aircraft in AVCS mode by operating the switch from the transmitter, and switch between them. You can set the holding power rate

selector switch to the channel with the AFR function of the transmitter, and set the point for each rate on the AFR point curve to

switch. It is also possible to use the ﬂight condition function to work with the ﬂight condition switch.

When set to SW of DG1 or DG2

Switch channel rate

Channel rate

When set to dial or lever

S.BUSBasic2/3Conﬁg6/7

Displayandadjustthecurrentrate

numbersC1toC5byoperating

thechannelonthetransmitter.

Byoperatingthechannelofthe

transmitter,thechannelposition

ofthecurrentratenumbersC1

toC5willbedisplayedingreen.

T16IZSOFTWAREUPDATECHANGES

V3.2

V3.1

1. Compatible with Futaba ESC MC-980H/A, MC-9130H/A, MC-9200H/A

Supports the telemetry function of MC-980H/A, MC-9130H/A, and MC-9200H/A.

1. Fixed an issue where the Vario Melody settings were not saved.

1. Fixed telemetry voice for Futaba ESC and Hobbywing ESC.

2. Fixed the problem that model copy fails.

This software updates or alters the functions and features noted below. The instructions and information that follow are meant as a supplement to the original

instruction manual that accompanied the T16IZ transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with

these instructions. Please check to ensure that the update has been installed.

1) Select the System Menu.

2) Touch the [Information] button.

3) Conﬁrm that the information in the display indicates the version numbers as noted above.

◆ RegistertheESCwithtransmitter. ◆ Alternatively,select[FutabaESC]instartslot24.

◆ TheregisteredESCwillbedisplayedas"FutabaESC".

ConnectSBM-2totheS.I/Fporton

thebackoftransmitter.

◆ Linkagemenu→Sensor→ 3/3

Registrationtotransmitter

● Callpage3of[Sensor].

*Pleasenotethattheproperdefaultslotforthisaccessoryisnumber8(8-

15).Thissensoruseseightslots.Beingmadetoastartslotare8,16,and

24.Informationonhowtochangetheslotassignmentisincludedinthe

transmitter'smanual.

ConnecttheSBM-2tothe

transmitterasshown,then

tapRegister.

Registrationiscompletewhen

thisscreenappears

Completeregistrationandremove

SBM-2fromthetransmitter.

◆The registered Hobbywing ESC is displayed as "Hobbywing ESC".

For details on Hobbywing ESC telemetry

support, refer to the Hobbywing website.

Alarmischosenfrom

Buzzer,Voice,and

Inhibit.

AllowsSpeechtobe

turnedONorOFF.

↑Anupwardarrow

indicatesthealarm

willsoundwhenthe

currentreachesabove

yoursetvalue.

↓Adownwardarrow

indicatesthealarm

willsoundwhenthe

currentreachesbelow

yoursetvalue.

*The current and capacity consumption display may vary

depending on the usage conditions, so use it as a guide.

◆ESC telemetry display screen

The ESC status is displayed. Alarm setting is also possible.

Displaymax/minvalue

Pressandholdtoreset.

Displaymax/minvalue

Pressandholdtoreset.

Taptomovetothe

currentsettingpage.

Taptomovetothe

voltagesettingpage.

Taptomovetothe

capacitysettingpage.

Taptomovetothe

rotationsettingpage.

Enterthenumberof

polesforyourmotor.

Whenenabled,thealarm

willbeactivatedinthe

followingwarningstate.

Ifthegearisdown,enter

thegearratiotodisplay

thehelicopterrotorspeed

andtheairplanegeardown

propellerspeed.

Whenenabled,thevibrator

willstartinthefollowing

warningstate.

◆ Warningstate

◆ AlarmscanbesetforVoltage,Capacity,Rotation,ESCtemperature,andThrottleusing

thesameprocedure.

ShowstheoutputlevelfromtheESC

tothemotor,notthepositionofthe

throttlestick.

Evenifthestickisinthe50%

position,theoutputmaynotbe50%

dependingontheESCsetting.

Throttlenotat0%

Lowvoltage

Overtemperature

Overcurrent

Motorlocked

Throttlesignallost

WhenthethrottlestickisnotlowwhenESCisstarted

Whenthebatteryvoltageisbelowthecutoﬀvoltage

WhentheESCtemperatureis110°Corhigher

Peakcurrentover

Whenthemotorlocks

Whennothrottlesignalisreceivedformorethan0.25s

Taptomovetothe

temperaturesettingpage.

Taptomovetothethrottlesetting

page.

◆ MC-9130H/Atelemetryconnectionexample

SBM-2

ESC

ToCH3

Tofreeport

Todrivebattery

Throttle

ToS.BUS2

◆ Alarmsetting

Setsthecurrenton

whichthealarm

operates.

1. Add GYA553 Airplane Gyro setting function. (Refer the T16IZ GYA553 Setting Manual)

2. Compatible with SCORPION ESC telemetry

Added support for SCORPION POWER SYSTEM ESC some models.

2. GYA553 Addition of setting parameters

AIL / ELE / RUD holding power setting has been added to the setting parameters of GYA553.

Adjusted the gyro holding force of the aircraft in AVCS mode.

Decreasing the value weakens the holding power and makes

the operation feeling closer to the Normal mode.

Autres manuels pour T16IZ

Table des matières

Autres manuels FUTABA Émetteur

FUTABA

FUTABA T6EXA Manuel utilisateur

FUTABA

FUTABA T7PXR Manuel technique

FUTABA

FUTABA R3008SB Manuel utilisateur

FUTABA

FUTABA 9CAP SUPER Manuel utilisateur

FUTABA

FUTABA FMT-02 Manuel utilisateur

FUTABA

FUTABA R7008SB Manuel utilisateur

FUTABA

FUTABA 9z Manuel utilisateur

FUTABA

FUTABA FP-6EX - ADDENDUM Manuel utilisateur

FUTABA

FUTABA FX-30 Mode d'emploi

FUTABA

FUTABA 3PRKA Manuel utilisateur

FUTABA

FUTABA FX-3/FMT-01 Manuel technique

FUTABA

FUTABA T14SG Instructions de montage

FUTABA

FUTABA R3006SB Manuel utilisateur

FUTABA

FUTABA T14SG Manuel technique

FUTABA

FUTABA FX-18 Manuel utilisateur

FUTABA

FUTABA R3006SB Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur