Furuno NAVNET 3D MFDBB Manuel utilisateur
www.furuno.co.jp
Installation Manual
Multi Function Display
MFDBB
SAFETY INSTRUCTIONS............................................................................i
SYSTEM CONFIGURATION.......................................................................ii
EQUIPMENT LISTS....................................................................................iii
1. MOUNTING............................................................................................1
1.1 Mounting the Control Unit.............................................................................................1
1.2 Mounting the Processor Unit ........................................................................................7
2. WIRING..................................................................................................9
2.1 Processor Unit Wiring...................................................................................................9
2.2 Control Unit Wiring .....................................................................................................14
3. SETTING UP THE EQUIPMENT .........................................................15
3.1 Setup for Single MFD in the Network .........................................................................17
3.2 Setup for Multiple MFDs in the Network.....................................................................28
PACKING LISTS......................................................................................A-1
OUTLINE DRAWINGS.............................................................................D-1
INTERCONNECTION DIAGRAM............................................................ S-1
i
WARNING
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warning, Caution
Mandatory Action
Prohibitive Action
SAFETY INSTRUCTIONS
The user and installer must read the appropriate safety instructions before attempting to install
or operate the equipment.
WARNING CAUTION
Ground the equipment to prevent
electrical shock and mutual interference.
Observe the following compass safe distances
to prevent interference to a magnetic compass:
ELECTRICAL SHOCK HAZARD
Do not open the equipment unless
totally familiar with electrical circuits.
Only qualified personnel should work
inside the equipment.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Be sure that the power supply is
compatible with the voltage rating of the
equipment.
Connection of an incorrect power supply
can cause fire or damage the equipment.
Standard
compass Steering
compass
MPU-001 1.45 m 0.90 m
MCU-001 0.55 m 0.40 m
DCU12 0.70 m 0.45 m
Use the proper fuse.
Use of an incorrect fuse may damage the equipment.
ii
SYSTEM CONFIGURATION
MONITOR
MU-155C/170C, etc.
VIDEO IN (CCD
CAMERA, MAX. 4)
LINE OUT
(SPKR, ETC.)
12-24 VDC*2
DISPLAY CONTROL
UNIT DCU12
CONTROL UNIT
MCU-001
AND/OR*3
HUB-101
GPS NAVIGATOR
GP-320B/330B
AIS RECEIVER,
HEADING SENSOR or
EXTERNAL BUZZER
USB DEVICE
(MOUSE, KYBD)
NMEA 2000
(SENSOR, ETC.)
POWER SUPPLY UNIT
PSU-013*1
: Standard Supply
: Optional Supply
: Local Supply
*1 Required with DRS25A
*2 See the table and figure below for
configurations for the PSU and rectifiers.
*3 Max. two units
PROCESSOR UNIT
MPU-001
RADAR SENSOR
DRS4A/DRS6A/DRS12A/DRS25A
OR
RADAR SENSOR
DRS2D/DRS4D
FISH FINDER
(DFF series, ETR-6/10N, ETR-30N)
Matrix for radar model, PSU and rectifiers
DRS2D/4D/
4A/6A/12A
MFDBB
RU-1746B-2
DRS25A
MFDBB
PSU-013
DRS25A
MFDBB
PSU-013
Radar
Model PSU Rectifier for
MFDBB Rectifier for
PSU Rectifier for
MFDBB+PSU
DRS2D Not
required RU-1746B-2
DRS4D
DRS4A
DRS6A
DRS12A
DRS25A PSU-013* RU-1746B-2 RU-3424
* Standard supply with DRS25A.
12-24 VDC*2
RU-1746B-2
12-24 VDC2
LINE IN (MIC,
for future use)
DRS25A
DRS4A
DRS6A
DRS12A
RU-1746B-2 RU-3424
JUNCTION
BOX FI-5002
iii
EQUIPMENT LISTS
Standard supply
*See the lists at the back of this manual.
Optional supply
Name Type Code No. Qty Remarks
Processor Unit MPU-001 - 1
Control Unit MCU-001 - 1 Choose one.
Display Control Unit DCU12 - 1
Installation Materials CP19-00600 000-011-664 1 set For MPU-001, Cable, CP19-
00601*
CP19-00700 000-011-663 1 set For MCU-001,
cable, CP19-
00701*
Choose one.
CP19-00800 000-011-662 For DCU12,
cables, CP19-
00801*
Spare Parts SP19-00501 001-023-090 1 set For MPU-001, fuses
SP19-00601 001-023-040 1 set For DCU-001, fuses
Accessories FP19-01201 001-033-760 1 For MCU-001, panel remover
FP19-01101 001-023-060 For DCU12, panel remover
Name Types Code No. Remarks
DVI-D Cable DVI-D/D SINGLELINK 000-149-054-10 5 m
DVI-D/D S-LINK 000-150-200-10 10 m
External Buzzer OP03-136 000-086-443
Rectifier RU-1746B-2 -
Network Hub HUB-101 -
Joint Box TL-CAT-012 000-167-140-10 For LAN cable extension
Junction Box FI-5002 000-010-765 For NMEA 2000
Control Unit MCU-001 -
Display Control
Unit DCU12 -
iv
Cable Assy MJ-A7SPF0007-050C 000-154-028-10 5 m, NMEA0183, w/7P
connector
MJ-A6SPF0016-005C 000-159-689-11 For FAX-30, ETR6N/10N
connection
MOD-Z072-020+ 000-167-175-10 2 m, LAN
MOD-Z072-050+ 000-167-176-10 5 m, LAN
MOD-Z072-100+ 000-167-177-10 10 m, LAN
MOD-Z073-030+ 000-167-171-10 3 m, for PC connection
M12-05BM+05BF-010 000-167-962-10 φ6, 1 m, NMEA 2000
M12-05BM+05BF-020 000-167-963-10 φ6, 2 m, NMEA 2000
M12-05BM+05BF-060 000-167-964-10 φ6, 6 m, NMEA 2000
M12-05BFFM-010 000-167-965-10 φ6, 1 m, NMEA 2000
M12-05BFFM-020 000-167-966-10 φ6, 2 m, NMEA 2000
M12-05BFFM-060 000-167-967-10 φ6, 6 m, NMEA 2000
CB-05PM+05BF-010 000-167-968-10 φ10, 1 m, NMEA 2000
CB-05PM+05BF-020 000-167-969-10 φ10, 2 m, NMEA 2000
CB-05PM+05BF-060 000-167-970-10 φ10, 6 m, NMEA 2000
CB-05BFFM-010 000-167-971-10 φ10, 1 m, NMEA 2000
CB-05BFFM-020 000-167-972-10 φ10, 2 m, NMEA 2000
CB-05BFFM-060 000-167-973-10 φ10, 6 m, NMEA 2000
NMEA connector LTWSS-050505-FMF-
TS001 000-168-603-10 NMEA 2000 distributor
(micro style)
LTWMC-05BMMT-
SL8001 000-168-604-10 NMEA 2000 terminator,
male (micro style)
LTWMC-05BFFT-
SL8001 000-168-605-10 NMEA 2000 terminator,
female (micro style)
LTWNC050505FMF-
TS001 000-160-507-10 NMEA 2000 distributor
(mini style)
LTWMN-05AMMT-
SL8001 000-160-508-10 NMEA 2000 terminator,
male (mini style)
LTWMN-05AFFT-
SL8001 000-160-509-10 NMEA 2000 terminator,
female (mini style)
Operator’s Manual OME-44460 -
NMEA 2000 Inter-
face Unit IF-NMEA2K1 -
Name Types Code No. Remarks
1
1. MOUNTING
1.1 Mounting the Control Unit
There are two types of control units: Control Unit MCU-001 and Display Control Unit DCU12. The
former is the keyboard type, and the latter has an LCD display and keyboard.
When selecting a mounting location for the control unit, keep the following in mind:
• The temperature and humidity at the mounting location should be moderate and stable.
• Locate the unit away from exhaust pipes and ventilators.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the unit away from electromagnetic field generating equipment such as motors and gen-
erators.
• For maintenance and checking purposes, leave sufficient space at the sides and rear of the unit
and leave slack in cables. Minimum recommended space is shown on the outline drawing for
the control units.
• Do not mount the DCU12 on the overhead.
• A magnetic compass will be affected if the control unit is placed too close to it. Observe the
compass safe distances shown in the SAFETY INSTRUCTIONS to prevent disturbance to the
magnetic compass.
2
1.1.1 Mounting procedure for control unit MCU-001
The control unit MCU-001 is designed to be flush mounted in a console or panel.
1. Prepare a cutout in the mounting location using the template sheet (supplied) for the MCU-
001.
2. Remove the front panel from the MCU-001 by grasping it at its sides and pulling it towards
you.
3. Attach the mounting sponge to the MCU-001.
4. Fix the MCU-001 by using four self-tapping screws (supplied) .
5. Attach the front panel to the MCU-001.
How to detach the front panel from the mounting place
To detach the front panel after mounting the unit, use the remover (supplied) as below. Do not
attempt to remove it by any other method, to prevent damage to the unit.
1. Set the remover to the left-side notch at the bottom of the unit.
Mounting
sponge
MCU-001
Cutout
Self-tapping screws
(4 pcs.)
Front panel
3
2. Pull the remover to raise the panel slightly.
3. Similarly use the remover to raise the panel at the right-side notch.
4. Insert the remover to the space at the one end of the unit, and pull it to raise the panel slightly.
Repeat this procedure for the opposite side.
5. Use the remover to raise the panel at the two notches on the upper side of the unit.
6. Use your hands to detach the front panel at both sides of it.
4
1.1.2 Mounting procedure for display control unit DCU12
The Display Control Unit DCU12 can be flush mounted in a console or panel, or mounted on a
desktop or the overhead.
Flush mounting
1. Prepare a cutout in the mounting location using the template sheet (supplied) for the DCU12.
2. Remove the front panel from the DCU12 by grasping it at its sides and pulling it towards you.
3. Attach the mounting sponge to the DCU12.
4. Fix the DCU12 by using four self-tapping screws (supplied).
5. Attach the front panel to the DCU12.
How to detach the front panel from the mounting place
To detach the front panel after mounting the unit, use the remover (supplied) as below. Note that
the front cover may be damaged if you do not follow the methods below.
1. Set the remover to a notch on the lower side of the unit.
Mounting sponge
Cutout
Front panel
Self-tapping screws
(4 pcs.)
DCU12
5
2. Pull the remover to raise the panel slightly. Do this for all notches on the lower side of the unit.
3. Insert the remover to the space at the one side of the unit, and pull the remover to raise the
panel slightly. Do the same for the opposite side.
4. Use your hands to detach the front panel from the lower side.
Autres manuels pour NAVNET 3D MFDBB
2
Table des matières
Autres manuels Furuno Moniteur
Furuno
Furuno MU-231 Manuel utilisateur
Furuno
Furuno MU-200 Manuel utilisateur
Furuno
Furuno Mu 120c Manuel utilisateur
Furuno
Furuno NAVNET TZTOUCH2 TZTL15F Guide d'installation
Furuno
Furuno Multi Instrument FI-504 Manuel utilisateur
Furuno
Furuno MU-152 Manuel utilisateur
Furuno
Furuno MU-170C Manuel
Furuno
Furuno TZTL12F Manuel utilisateur
Furuno
Furuno Mu-190HD Manuel utilisateur
Furuno
Furuno FMD-1712 Manuel utilisateur
Furuno
Furuno TZT12F Manuel
Furuno
Furuno Mu 120c Manuel utilisateur
Furuno
Furuno TZT9 Mode d’emploi
Furuno
Furuno RD-30 Manuel utilisateur
Furuno
Furuno MFD12 Manuel utilisateur
Furuno
Furuno MU-190V Manuel utilisateur
Furuno
Furuno MU-170C Manuel utilisateur
Furuno
Furuno FMD1920C Manuel utilisateur
Furuno
Furuno TZT16F Manuel utilisateur
Furuno
Furuno RD-20 Manuel utilisateur
