Furuno MU-155C Manuel utilisateur
MULTI-PURPOSE LCD DISPLAY
MU-155C
Back
The paper used in this manual
is elemental chlorine free.
FURUNO Authorized Distributor/DealerFURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,9-52 Ashihara-cho,
Nishinomi
y
a 662-8580, JAPANNishinomi
y
a 662-8580, JAPAN
Tele
p
hone :Tele
p
hone : 0798-65-21110798-65-2111
FaxFax 0798-65-42000798-65-4200
::
FIRST EDITION :FIRST EDITION : JUN.JUN. 20042004
Printed in JapanPrinted in Japan
A
ll ri
g
hts reserved.
A
ll ri
g
hts reserved.
A3A3 :: OCT.OCT. 24, 200624, 2006
Pub. No.Pub. No. OME-20300OME-20300
*
00014970000
*
*
00014970000
*
*
00014970000
*
*
00014970000
*
(( YOSHYOSH )) MU-155CMU-155C * 0 0 0 1 4 9 7 0 0 0 0 ** 0 0 0 1 4 9 7 0 0 0 0 *
*
OME
20300
A
30
*
*
OME
20300
A
30
*
*
OME
20300
A
30
*
*
OME
20300
A
30
*
* O M E 2 0 3 0 0 A 3 0 ** O M E 2 0 3 0 0 A 3 0 *
i
SAFETY INSTRUCTIONS
Safety Instructions for the Operator
WARNING
Do not open the equipment.
Only qualified personnel
should work inside
the equipment.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Use the proper fuse and power cable.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Do not place any object near the exhaust
or intake vent.
Fire may result.
CAUTION
A warning label is attached to the
equipment. Do not remove the label.
If the label is missing or damaged,
contact a FURUNO agent or dealer.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-231
WARNING
Do not open the cover
unless totally familiar with
electrical circuits and
service manual.
Improper handling can result
in electrical shock.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the equip-
ment.
Safety Instructions for the Installer
CAUTION
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
When lifting the display unit, hold it
together with the hard cover.
Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.
LCD Monitor MU-155C
Standard Steering
compass compass
0.3 m 0.3 m
Remote Controller
RMC-200
1.55 m 1.0 m
Do not connect/disconnect the signal
cable while turning the power on.
The unit may be damaged.
ii
TABLE OF CONTENTS
FOREWORD ........................................................................................................iii
SYSTEM CONFIGURATION................................................................................ iv
EQUIPMENT LISTS .............................................................................................. v
1. MOUNTING.......................................................................................................1
1.1 Display Unit.....................................................................................................................1
1.2 Remote Controller...........................................................................................................4
2. WIRING .............................................................................................................5
3. ADJUSTMENTS................................................................................................7
3.1 RGB/DVI Setting.............................................................................................................7
3.2 VIDEO Setting.................................................................................................................9
3.3 Menu Window Setting ...................................................................................................10
3.4 Remote Controller Setting.............................................................................................12
4. OPERATION.................................................................................................... 13
4.1 Controls.........................................................................................................................13
4.2Adjusting Display Brilliance............................................................................................15
4.3 Choosing Source for Main Picture.................................................................................16
4.4 Choosing Source for Picture-in-Picture..........................................................................17
5. MAINTENANCE, TROUBLESHOOTING .......................................................18
5.1 Maintenance..................................................................................................................18
5.2 Troubleshooting.............................................................................................................19
5.3 Clearing the Memory.....................................................................................................20
SPECIFICATIONS...........................................................................................SP-1
PACKING LISTS............................................................................................... A-1
OUTLINE DRAWINGS...................................................................................... D-1
INTERCONNECTION DIAGRAM ......................................................................S-1
iii
FOREWORD
A Word to the Owner of the MU-155C
FURUNO Electric Company thanks you for purchasing the MU-155C 15” Multi-Purpose
LCD Display. We are confident you will discover why the FURUNO name has become
synonymous with quality and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for
quality and reliability throughout the world. This dedication to excellence is furthered by our
extensive global network of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless properly
installed and maintained. Please carefully read and follow the operation, installation and
maintenance procedures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our
purposes.
Thank you for considering and purchasing FURUNO.
Features
• Main or remote display for radars, video sounders, sonars, plotter. Compatible
equipment: FAR-21X7 series, MODEL1833C/1833C-BB series (NavNet),
FCV-1200L/1200LM, CH-250, CH-270, CSH-5L/8L, GD/GP-280/380/680, etc.
• High resolution display of 1024 x 768dot (XGA)
• Brightness of 1,000 cd/m2(maximum) and 5 cd/m2(minimum) for comfortable viewing
day and night
• Landscape orientation
• Wide viewing angle for observation by more than one person
• Picture-in-picture function
i
v
SYSTEM CONFIGURATION
12-24 VDC
CCD camera,
Video recorder, etc.
FAR-2107 series etc.
Radar, Video Plotter,
Navigator, Video So nder,
Scanning Sonar, etc.
RGB
DVI
VIDEO (NTSC/PAL)
Connectable equipment
Equipment Resolution Signal
FR-1500 MK3 series XGA Analog
FCV-1200L/1200LM* VGA Analog, via IF8000
GD/GP-280/380/680 VGA Analog
CH-250 VGA Analog, via IF8000
CH-270 VGA Analog, via IF8000
CSH-5L/8L XGA Analog
FSV-24/24S/30/30S SXGA Analog
FR-21X5 series SXGA Analog
FAR-21X7 series SXGA DVI
FEA-2107 SXGA DVI
MODEL 1833C series VGA Analog
MODEL 1833C-BB series VGA Analog
*= Not available for the portrait type.
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01%
of the pixels may drop out or blink, how-
ever this is not an indication of malfunc-
tion.
About the TFT LCD
v
EQUIPMENT LISTS
Standard supply
Name Type Code No. Qty Remarks
Display Unit MU-155C −1 w/hard cover
Remote Controller RMC-200 000-012-629 1
Spare Parts* SP19-00201 001-410-490 1 set
Installation Materials* CP19-00200 000-012-641 1 set
Accessories* FP19-00801 001-410-510 1 set
Option
Name Type Code No. Qty Remarks
Hanger FP19-00900 001-410-540 1 w/knob, self-tapping screws
000-146-500 1 Cable length: 5 m
3COX-2P-6C 000-146-501 1 Cable length: 10 m
Cable Assy
DVI-D/D SINGLELINK5M 000-149-054 1 Cable length: 5 m
Remote
Controller RMC-200 000-012-629 1
* = See packing list at the end of this manual.
1
1. MOUNTING
Refer to the outline drawing at the end of this manual for mounting dimensions.
Note:Agrass plate covers the LCD. For this reason, handle the unit carefully.
1.1 Display Unit
The display unit may be mounted on a desktop (optional hanger required) or flush mounted
in a panel.
When selecting a mounting location, keep in mind the following points:
• Locate the unit out of direct sunlight.
• Select a location where the display can be easily viewed and the controls can be easily
operated.
• Leave sufficient space around the unit for servicing and maintenance. See the outline
drawing for minimum servicing space.
• The unit weighs 7.9 kg (flush mounting)/9.1 kg (desktop mounting). Be sure the
mounting location is strong enough to support the weight of the unit.
• Locate the unit away from areas subject to water splash and rain.
2
Flush mounting
See the outline drawing at the end of this manual for mounting dimensions.
CAUTION
Hold the hard cover and display unit
together when lifting the display unit.
The display unit may fall out if only the
hard cover is held.
1. Remove the hard cover from the unit.
2. Using the paper template supplied in the installation materials, make a cutout in the
mounting location.
3. Set the display unit to the cutout, and fasten it with four self-tapping screws (5X40,
supplied as accessories).
Note: Hex head bolts may also be used to fasten the display unit. However, their lengths
must be 10 mm longer than the wall thickness.
Waterproofing: IP20
Waterproofing: IPX5
30
130
Cosmetic cap
Minimum: 50
Mounting dimensions
4. Attach the cosmetic caps (supplied as accessories) to the display unit at the locations
shown in the drawing above.
5. Attach hard cover to protect the LCD.
3
Desktop mounting
The display unit can be mounted on a desktop, using the optional hanger,
Type: FP19-00900, Code No.: 001-410-540.
Contents of hanger mounting kit
Name Type Code No. Qty
Hanger FP19-00901 001-410-550 1
Knob bolt FP03-09204 008-523-650 2
Self-tapping screw 5x20 000-802-081 4
1. Fasten the hanger to the mounting location with four self-tapping screws (supplied).
Note: Do not mount the unit where the exhaust or intake vent may be obstructed.
Intake vent
Exhaust vent
Display unit, rear view
2. Screwknob bolts in unit.
3. Set unit to hanger, and then tighten knob bolts.
4. Remove the hard cover from the unit.
5. Attach the cosmetic caps (supplied as accessories) to the unit at the locations shown in
the drawing below.
6. Attach hard cover to protect the LCD.
Knob bolt
Hanger
Cosmetic cap
Desktop mounting
Autres manuels pour MU-155C
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Furuno Moniteur
Furuno
Furuno NAVNET TZTOUCH2 TZTL15F Manuel utilisateur
Furuno
Furuno FMD-811 Manuel utilisateur
Furuno
Furuno RD-30 Manuel utilisateur
Furuno
Furuno TZTL12F Manuel utilisateur
Furuno
Furuno RD-33 Manuel utilisateur
Furuno
Furuno NAVNET TZTOUCH2 TZTL15F Guide d'installation
Furuno
Furuno TZT9 Mode d’emploi
Furuno
Furuno FMD3100 Manuel utilisateur
Furuno
Furuno TZTL12F Manuel utilisateur
Furuno
Furuno Mu-190HD Manuel utilisateur
Furuno
Furuno NAVNET TZ2 TZTL12F Manuel utilisateur
Furuno
Furuno MU-190V Manuel utilisateur
Furuno
Furuno MU-151C Manuel utilisateur
Furuno
Furuno TZT16F Manuel utilisateur
Furuno
Furuno RD-50 Manuel utilisateur
Furuno
Furuno MFD12 Manuel utilisateur
Furuno
Furuno ECDIS FEA-2100 Manuel utilisateur
Furuno
Furuno Mu 120c Manuel utilisateur
Furuno
Furuno RD-50 Manuel utilisateur
Furuno
Furuno MU-151C Manuel utilisateur
