Fujitsu MAP3147NC - Enterprise - Hard Drive Manuel utilisateur
C141-E166-01EN
MAP3147NC/NP
MAP3735NC/NP
MAP3367NC/NP
DISK DRIVES
PRODUCT/MAINTENANCE MANUAL
C141-E166
FOR SAFE OPERATION
Handling of This manual
This manual contains important information for using this product. Read thoroughly before using the
product. Use this product only after thoroughly reading and understanding especially the section “ mportant
Alert tems” in this manual. Keep this manual handy, and keep it carefully.
FUJ TSU makes every effort to prevent users and bystanders from being injured or from suffering damage
to their property. Use the product according to this manual.
IMPORTANT NOTE TO USERS
READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE
TO USERS, BYSTANDERS OR PROPERTY.
While FUJ TSU has sought to ensure the accuracy of all information in this manual, FUJ TSU assumes no
liability to any party for any damage caused by any error or omission contained in this manual, its updates
or supplements, whether such errors or omissions result from negligence, accident, or any other cause. n
addition, FUJ TSU assumes no liability with respect to the application or use of any porduct or system in
accordance with the descriptions or instructions contained herein; including any liability for incidental or
consequential damages arising therefrom.
FUJTSU D SCLA MS ALL WARRANT ES REGARD NG THE NFORMAT ON CONTA NED
HERE N, WHETHER EXPRESSED, MPL ED, OR STATUTORY.
FUJ TSU reserves the right to make changes to any products described herein without further notice and
without obligation.
This product is designed and manufactured for use in standard applications such as office work, personal
devices and household appliances. This product is not intended for special uses (atomic controls,
aeronautic or space systems, mass transport vehicle operating controls, medical devices for life support, or
weapons firing controls) where particularly high reliability requirements exist, where the pertinent levels of
safety are not guaranteed, or where a failure or operational error could threaten a life or cause a physical
injury (hereafter referred to as "mission-critical" use). Customers considering the use of these products for
mission-critical applications must have safety-assurance measures in place beforehand. Moreover, they are
requested to consult our sales representative before embarking on such specialized use.
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media without the
express written permission of Fujitsu Limited.
All Right Reserved, Copyright © FUJ TSU L M TED 2002
C141-E166 i
REVISION RECORD
Edition Date published Revised contents
01 May, 2002
Specification No.: C141-E1 -**EN
ii C141-E166
Related Standards
Product specifications and functions described in this manual comply with the following ANS
(*1) standards.
Document number Title
T10/1236D Rev.20
[NC TS.351:2001]
SCS Primary Commands-2 (SPC-2)
T10/996D Rev.8c
[NC TS.306:1998]
SCS -3 Block Commands (SBC)
T10/1157D Rev.20 SCS Architecture Model-2 (SAM-2)
T10/1365D Rev.7 SCS Parallel nterface-4 (SP -4)
*1 ANS = American National Standard nstitute
n case of conflict between this manual and any referenced document, this manual takes
precedence.
C141-E166 iii
PREFACE
This manual describes the MAP3147NC/NP, MAP3735NC/NP and MAP3367NC/NP hereafter, MAP
series), 3.5 type fixed disk drives with an embedded SCSI controller.
This manual details the specifications and functions of the above disk drive, and gives the requirements and
procedures for installing it into a host computer system.
This manual is written for users who have a basic understanding of fixed disk drives and their use in
computer systems. The MANUAL ORGANIZATION section describes organization and scope of this
manual. The need arises, use the other manuals.
OVERVIEW OF MANUAL
This manual consists of the following eight chapters:
Chapter 1 GENERAL DESCRIPTION
This chapter introduces the MAP series disk drives and discusses their standard features, hardware, and
system configuration.
Chapter 2 SPECIFICATIONS
This chapter gives detailed specifications of the MAP series disk drives and their installation environment.
Chapter 3 DATA FORMAT
This chapter describes the data structure of the disk, the address method, and what to do about media
defects.
Chapter 4 INSTALLATION REQUIREMENTS
This chapter describes the basic physical and electrical requirements for installing MAP series disk drives.
Chapter 5 INSTALLATION
This chapter explains how to install MAP series disk drives. It includes the notice and procedures for
setting device number and operation modes, mounting the disk drive, connecting the cables, and confirming
drive operation.
Chapter DIAGNOSIS and MAINTENANCE
This chapter describes the automatic diagnosis, and maintenance of MAP series disk drive. This chapter
also describes diagnostic methods for operation check and the basics of troubleshooting the disk drives.
Chapter 7 ERROR ANALYSIS
This chapter describes in details how collect the information for error analysis and how analyze collected
error information.
APPENDIX A to B
The appendixes give supplementary information, including a list of setting items and the signal assignments
of interface connector.
iv C141-E166
CONVENTIONS FOR ALERT MESSAGES
This manual uses the following conventions for alerts to prevent physical or property damages to users or
by standards.
DANGER This indicates that personal injury will occur if
the user does not perform the procedure
correctly.
WARNING This indicates that personal injury could occur if
the user does not perform the procedure
correctly.
CAUTION This indicates that either minor or moderate
personal injury may occur if the user does not
perform the procedure correctly.
NOTICE This indicates that inconvenience to the user
such as damages to the product, equipment, data,
and/or other property may occur if the user does
not pay attention or perform the procedure
correctly.
IMPORTANT This indicates information that the helps the user
use the product more effectively.
CONVENTIONS USED IN THIS MANUAL
The MAP3147NC/NP, MAP3735NC/NP and MAP3367NC/NP disk drives are described as "the intelligent
disk drive ( DD)", "the drive" or "the device" in this manual.
Decimal number is represented normally.
Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.
Binary number is represented as "010".
ATTENTION
Please forward any comments you may have regarding this manual.
To make this manual easier for users to understand, opinions from readers are needed. Please write your
opinions or requests on the Comment at the back of this manual and forward it to the address described in
the sheet.
C141-E166 v
Important Alert Items
Important Alert Messages
The important alert messages in this manual are as follows:
A hazardous situation could result in minor or moderate personal injury if the
user does not perform the procedure correctly This alert signal also indicates
that damages to the product or other property may occur if the user does not
perform the procedure correctly
Task Alert message Page
Data loss
For MAP series, Reed Solomon codes are applied for their ECC.
The sector data is divided into 6 interleaving sectors, and ECC is
performed in each sector where the maximum number of errors
(up to 5 byte) can be corrected. [Total maximum byte: 5 byte
×
6
( interleave) = 30 byte]
If the error of read sector keeps allowable error byte number,
correction is performed.
However, if error byte exceeds its allowable number, correction
may not be performed properly
Hot temperature
To prevent injury, do not handle the drive until after the device has
cooled sufficiently after turning off the power. The DE and LSI
become hot during operation and remain hot immediately after
turning off the power.
Data loss
1. The user must not change the setting of terminals not described
in this section. Do not change setting status set at factory
shipment.
2. Do not change the setting of terminals except following setting
pins during the power is turned on.
• Write protect: CN2 9 10 (NP model only)
3. To short the setting terminal, use the short plug attached when
the device is shipped from the factory.
2-5
5-1
5-5
Mounting Installation
Damage
1. Make sure that system power is off before connecting or
disconnecting cables.
2. Do not connect or disconnect cables when power is on.(except
NC model)
5-11
vi C141-E166
Task Alert message Page
Damage
1. Be careful of the insertion orientation of the SCSI connectors.
With the system in which terminating resistor power is supplied
via the SCSI cable, if the power is turned on, the overcurrent
protection fuse of the terminating resistor power supplier may
be blown or the cable may be burnt if overcurrent protection is
not provided.
When the recommended parts listed in able 4.2 are used,
inserting the cables in the wrong direction can be prevented.
2. o connect SCSI devices, be careful of the connection position
of the cable. Check that the SCSI device with the terminating
resistor is the last device connected to the cable.
5-11
Mounting Installation
Data loss
When the SEND DIAGNOS IC command terminates with the
CHECK CONDI ION status, the INI must collect the error
information using the REQUES SENSE command. he RECEIVE
DIAGNOS IC RESUL S command cannot read out the error
information detected in the self-diagnostics.
Caution
1. o avoid shocks, turn off the power before connecting or
disconnecting a cable, connector, or plug.
2. o avoid injury, do not touch the mechanical assembly during
disk drive operation.
3. Do not use solvents to clean the disk drive.
Caution
1. Always ground yourself with a wrist strap connected to ground
before handling. ESD (Electrostatics Discharge) may cause
the damage to the device.
2. o prevent electrical damage to the disk drive, turn the power
off before connecting or disconnecting a cable, connector, or
plug.
3. Do not remove a PCA. his operation is required to prevent
unexpected or unpredictable operation.
4. Do not use a conductive cleaner to clean a disk drive assembly.
5. Ribbon cables are marked with a colored line. Connect the
ribbon cable to a cable connector with the colored wire
connected to pin 1.
Damage
Never open the disk enclosure in the field. Opening the disk
enclosure may cause an irreparable fault.
Data loss
Save data stored on the disk drive before requesting repair. Fujitsu
does not assume responsibility if data is destroyed during servicing
or repair.
6-4
6-5
6-6
6-6
6-15
6-7
C141-E166 vii
MANUAL ORGANIZATION
PRODUCT/
MAINTENANCE
MANUAL
(This manual
1. General Description
2. Specifications
3. Data Format
4. Installation Requirements
5. Installation
6. Diagnostics and Maintenance
7. Error Analysis
SCSI Physical
Interface
Specifications
1. SCSI Bus
2. SCSI Message
3. SCSI Bus Error Recovery Processing
SCSI Logical
Interface
Specifications
1. Command Processing
2. Data Buffer Management
3. Command Specification
4. Sense Data and error Recovery Procedure
5. Disk Medium Management
This page is intentionally left blank.
Autres manuels pour MAP3147NC - Enterprise - Hard Drive
1
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Fujitsu Stockage
Fujitsu
Fujitsu MAG3182FC SERIES Manuel utilisateur
Fujitsu
Fujitsu ETERNUS AF250 Manuel utilisateur
Fujitsu
Fujitsu ETERNUS DX100 S4 Instructions de montage
Fujitsu
Fujitsu ETERNUS AF S3 Series Mode d’emploi
Fujitsu
Fujitsu MHW2120BK Manuel utilisateur
Fujitsu
Fujitsu MHU2100AT Manuel utilisateur
Fujitsu
Fujitsu MAT3300NC/NP Product/ Manuel utilisateur
Fujitsu
Fujitsu ETERNUS DX Disk Manuel utilisateur
Fujitsu
Fujitsu Eternus DX600 S3 Instructions de montage
Fujitsu
Fujitsu M2266S Note de version
Fujitsu
Fujitsu MHW2040AC Manuel utilisateur
Fujitsu
Fujitsu ETERNUS DX100 S3 Manuel utilisateur
Fujitsu
Fujitsu M2301B Manuel utilisateur
Fujitsu
Fujitsu GP5-HDH461 Manuel utilisateur
Fujitsu
Fujitsu MBB2147RC SERIES Manuel utilisateur
Fujitsu
Fujitsu ETERNUS DX60 S3 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY LTO2 Manuel utilisateur
Fujitsu
Fujitsu ETERNUS AX Series Manuel utilisateur
Fujitsu
Fujitsu PG-HD2E4H Manuel utilisateur
Fujitsu
Fujitsu MHV2080AS - Extended Duty Mobile 80 GB Hard... Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur