Fujitsu PRIMEQUEST 500A Series Manuel utilisateur

C122-E001-10EN

Front Cover

INSTALLATION MANUAL

C122-E001-10EN

FOR SAFE OPERATION

This manual contains important information regarding the use and handling of this

product. Read this manual thoroughly. Pay special attention to the section "NOTE

ON SAFETY" Use the product according to the instructions and information

available in this manual. Keep this manual handy for further reference.

Fujitsu makes every effort to prevent users and bystanders from being injured or from

suffering damage to their property. Use the product according to this manual.

ABOUT THIS PRODUCT

This product is designed and manufactured for use in standard applications such as

office work, personal device, household appliance, and general industrial

applications. This product is not intended for use in nuclear-reactor control systems,

aeronautical and space systems, air traffic control systems, mass transportation

control systems, medical devices for life support, missile launch control systems or

other specialized uses in which extremely high levels of reliability are required, the

required levels of safety cannot be guaranteed, or a failure or operational error could

be life-threatening or could cause physical injury (referred to hereafter as "high-risk"

use). You shall not use this product without securing the sufficient safety required for

high-risk use. If you wish to use this product for high-risk use, please consult with

sales representatives in charge before such use.

C122-E001-10EN

RADIO FREQUENCY INTERFERENCE STATEMENT

The following notice is for EU users only.

The following notice is for USA users only.

Laser standards

WARNING: This is a product which meets Class A of EN55022. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate

measures.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This equipment includes Class 1 laser products and complies with FDA Radiation Performance

Standards, 21 CFR 1040.10 and 1040.11, and the International Laser Safety Standards IEC60825-

1: 2001.

C122-E001-10EN

TRADEMARK ACKNOWLEDGEMENTS

zMicrosoft, Windows, MS, Windows NT, and Windows Server are trademarks or

registered trademarks of Microsoft Corporation in the United States and/or other

countries.

zLinux is a trademark or registered trademark of Linus Torvalds in the United States

and other countries.

zRed Hat, RPM, and all Red-Hat-based marks and logos are trademarks or

registered trademarks of Red Hat, Inc. in the United States and other countries.

zSUSE is a trademark of Novell, Inc. in the United States and other countries.

zIntel, Xeon, and Itanium are trademarks or registered trademarks of Intel

Corporation.

zEthernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corporation

in the United States and other countries.

zAll other product names mentioned herein are the trademarks or registered

trademarks of their respective owners.

zSystem and product names in this manual are not always noted with trademark or

registered trademark symbols (™), (®).

TERMS AND CONDITIONS

The product includes software provided by third parties in addition to that provided

by Fujitsu Ltd. You are granted permission to use the third parties' software subject to

the terms and conditions below. If you acquire the source code of the software to

which the following terms and conditions apply, refer to LICENSE1_EN.pdf and

LICENSE2_EN.pdf, which are provided with the 'PRIMEQUEST Manuals'

(C122-E013-C2).

THIS SOFTWARE IS PROVIDED "AS IS" AND FUJITSU LIMITED MAKES NO

WARRANTIES, EITHER EXPRESSED OR IMPLIED, AS TO ANY MATTER

WHATSOEVER REGARDING TO THIS SOFTWARE, INCLUDING, WITHOUT

LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY

PARTICULAR PURPOSE.

IN NO EVENT SHALL FUJITSU LIMITED BE LIABLE FOR ANY CLAIM

FROM A THIRD PARTY, OR SPECIAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF

USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,

NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN

CONNECTION WITH THE USE, COPYING, MODIFICATION OR

DISTRIBUTION OF THIS SOFTWARE.

Fujitsu Ltd, April 2006

C122-E001-10EN

The contents of this manual shall not be disclosed in any way or reproduced in any

media without the express written permission of Fujitsu Limited.

C122-E001-10EN

Revision History

Edition Date Revised section

(Added/ Deleted/ Altered)

(Note) Details

01 2005-07-11 ⎯ ⎯

02 2005-09-16 All chapters

(correction)

CHAPTER 3 and 4

(correction)

Technical brushup

Addition of description for

Windows version

03 2005-10-31 All chapters (correction) Error corrections

04 2006-02-20 All chapters (correction) Addition of description for

PRIMEQUEST 420

05 2006-04-17 CHAPTER 2 (correction)

CHAPTER 2 (correction)

CHAPTER 4, Appendix E

(correction)

Addition of notes for network

settings

Correction of the procedures

for Linux installation

Addition of notes for PSA

installation

06 2006-08-11 All chapters (correction)

CHAPTER 2 (correction)

APPENDIX A (correction)

APPENDIX D (correction)

Addition of description for

PRIMEQUEST 500 series

Addition of description for

SUSE

Addition of description and

notes for XPAR setting

Addition of description for

software programs supplied

with the PRIMEQUEST

hardware

Correction of description for

the EFI driver setting

Addition of notes on replacing

an FC card

07 2007-03-05 CHAPTER 4, APPENDIX E

(correction)

Correction of description for

Watchdog setting

C122-E001-10EN

Edition Date Revised section

(Added/ Deleted/ Altered)

(Note) Details

08 2007-08-31 Section 4.8 (correction) Addition of description for

Linux dump function kdump

09 2008-03-10 Entire manual (addition) Addition of description for

PRIMEQUEST 580A/540A/

520A

10 2008-04-10 Entire manual (correction) Technical brushup

Note: In this table, the revised section is indicated by its section number in the

current edition.

An asterisk (*) indicates a section in the previous edition.

C122-E001-10EN i

Preface

This manual describes the preparation for PRIMEQUEST installation,

PRIMEQUEST power-on/off sequences, initialization procedures, and software

installation methods. This manual is intended for system administrators.

This section explains

zStructure and Contents of this Manual

zOther Reference Manuals

zAbbreviations

zText Conventions

zSyntax of the Command Line Interface (CLI)

zNotes Regarding Notations Used in This Manual

zConventions for Alert Messages

zEnvironmental Requirements for Using This Product

zReader Feedback

Structure and Contents of this Manual

This manual is organized as described below:

CHAPTER 1 PRIMEQUEST Overview

Provides an overview of the hardware, software, and network connections and

describes the workflow leading up to the initiation of operation.

CHAPTER 2 Setup

Describes how to perform the setup procedures required after installing the main unit.

CHAPTER 3 Operating System Installation

Describes the operating systems that can be installed, types of installation methods,

and operating system installation procedures.

CHAPTER 4 Work Required After Operating System Installation

Describes how to install and set up various software programs after installing the

operating system.

CHAPTER 5 Security Setup

Describes the SNMP and security settings.

ii C122-E001-10EN

Preface

CHAPTER 6 GSWB Initialization

Describes the initial settings required for using the optional GSWB product.

Appendix A Software Programs Supplied with the PRIMEQUEST

Hardware

Describes the software programs supplied with PRIMEQUEST.

Appendix B Installation Procedure

Provides instructions applicable to PRIMEQUEST installation.

Appendix C Power Control

Describes power-on and power-off.

Appendix D Installation in the SAN Boot Environment

Describes how to set up the SAN boot environment.

Appendix E Setting Item List

Provides lists of default values for the MMB (server management unit) and PSA

(PRIMEQUEST Server Agent).

Appendix F Overall View of Management LAN IP Addresses

Describes the IP addresses used for PRIMEQUEST.

Glossary

Explains the terms used in this manual.

Index

Provides keywords and corresponding reference page numbers so that the reader can

easily search for items in this manual as necessary.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Serveur

Fujitsu

Fujitsu SPARC Enterprise T5140 Guide d'installation

Fujitsu

Fujitsu PRIMERGY RX600 S4 Manuel utilisateur

Fujitsu

Fujitsu SPARC Enterprise T5440 Server Guide d'installation

Fujitsu

Fujitsu PRIMERGY TX200FT S2 Mode d’emploi

Fujitsu

Fujitsu PRIMERGY SX05 S1 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX900 S2 Manuel utilisateur

Fujitsu

Fujitsu SPARC Enterprise T5140 Manuel utilisateur

Fujitsu

Fujitsu FUTRO S930 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY TX300 S3 Manuel du propriétaire

Fujitsu

Fujitsu SPARC Enterprise M3000 Manuel de service

Fujitsu

Fujitsu PRIMEQUEST 1000 Series Instructions de montage

Fujitsu

Fujitsu CELVIN NAS QE807 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY CX2550 M1 Manuel utilisateur

Fujitsu

Fujitsu BS2000/OSD Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX2530 M5 Manuel utilisateur

Fujitsu

Fujitsu BS2000 SE Series Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY TX300 S7 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX600 S6 Manuel utilisateur

Fujitsu

Fujitsu SPARC Enterprise T5120 Manuel d'installation et d'exploitation

Fujitsu

Fujitsu PRIMERGY BX922 S2 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY RX200 S3 Mode d’emploi

Fujitsu

Fujitsu PRIMERGY RX600 S3 Mode d’emploi

Fujitsu

Fujitsu SPARC Enterprise M8000 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY CX270 S1 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur