Fujitsu ScanPartner 15C Guide de référence

ScanPartner15C\600C\620C\93GX\3091DC\3092DC

Win95\98\ME Installation Procedure

Rev050404A

Step A: Removing the shipping bracket.

It is recommended that before you connect the scanner to your computer that you inspect the

scanner and remove the shipping bracket first. The SP3091\3092DC’s do not have shipping

locks.

Removing the shipping bracket: Your ScanPartner comes with a factory installed

shipping bracket designed to protect the scanner during shipment. Before the scanner

can be used, the shipping bracket must be removed. Follow these instructions to remove

the shipping bracket:

1. Tilt the scanner on its side as shown in figure 2-1

2. Unscrew the retainer screw and remove the shipping bracket.

3. Place the shipping bracket in the “use position” slot and secure it with the retainer

screw (see figure 2-2)

4. Place scanner back in its normal position

ScanPartner15C\600C\620C\93GX\3091DC\3092DC

Win95\98\ME Installation Procedure

Rev050404A

Next connect the power cord to the scanner and a wall outlet, and then turn on the scanner.

The power, ready and paper jam LED will all light up, afterwards the scanner will complete its

self initialization and the paper jam light will go off in approximately 10 seconds. The SP93GX

power LED will flash and then go solid. The SP3091\3092DC’s will flash a P, 0, and then 1.

Once this step is completed turn off the scanner and install the SCSI host adapter.

Step B: Installing the AVA2902E SCSI Host Adapter

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot.

Make sure that the card is seated completely in the slot and secured in the frame.

Warning! Failure to secure the SCSI controller in the PC can result in damage to the

SCSI card, scanner, and/or your system.

4. Next boot your PC without the scanner attached and go to device manager. The

SCSI controller will be listed as “aic78xx” and should be at IRQ 15 or lower and not

sharing its IRQ with any other device in the system.

Step C: Installing the SCSI drivers

1. When the New Hardware wizard comes up allow Windows to finish installing the files

for the SCSI controller.

2. Then go to www.adaptec.com, and click on the “search” tab. Scroll down to the

“Enter key word or quoted phrase” box and type in “aspi32.exe.”

3. Next scroll down to the drivers section, click on “aspi32.exe” and follow the prompts

to download it to your desktop or a new folder.

4. Afterwards go to that location and double click on the "aspi32.exe" icon.

5. Follow the prompts.

6. Reboot and check for errors. If no errors shut down your system and go to the next

step.

Step D: Connecting the Scanner.

Warning ensure that the power is off when connecting or disconnecting any cables to the

scanner or workstation.

Setting the SCSI ID: The factory setting for the Scanner is 6, however, selecting a

different SCSI ID may be required when there are several devices on a SCSI chain.

Using a suitable tool, turn the selector switch until the arrow points to the desired ID

number (see figure 2-3). Setting the ScanPartner SCSI ID to 0, 1, or 7 is NOT

recommended as these settings are typically reserved for hard drives and the SCSI host

adapter.

Setting Termination: The Fujitsu ScanPartner comes complete with a built in SCSI

terminator (see Fig 2-3). If the Scanner is the last device in the SCSI chain, the

terminator should be switched to ‘On’. If the Scanner is not the last device, the

terminator should be off.

ScanPartner15C\600C\620C\93GX\3091DC\3092DC

Win95\98\ME Installation Procedure

Rev050404A

Connecting SCSI cable: Included with the ScanPartner is a SCSI cable used to connect

the scanner to the host adapter. Located on the back of the scanner are 2 SCSI ports,

one 50-pin centronics and one DB25-pin. The SP93GX has two 50-pin centronics ports.

Use the cable provided to connect to the 50-pin centronics port and the DB25-pin port on

the SCSI controller. The SP3091\3092DC’s have 2 High Density (HD) 50-pin

connectors. Ensure all connections are securely fastened.

WARNING! DO NOT connect the scanner to the parallel port on the workstation. Doing

so may damage the scanner).

Powering On: For proper communication between the Scanner and the Workstation,

switch on the scanner prior to switching on the workstation. The power, ready and paper

jam LED will all light up, afterwards the scanner will complete its self initialization and the

paper jam light will go off in approximately 10 seconds. The SP93GX power LED will

flash and then go solid. The SP3091\3092DC’s will flash a P, 0, and then 1.

Bootup the system: When the New Hardware wizard comes up, allow it to search your

system for the scanner. Next, when you get the no device driver found message, select

finish. SPECIAL NOTE: There is no INF file at this time, therefore the scanner will be

placed under "other devices" with a “?” in device manager. This is normal.

Step E: Installing the ISIS driver.

1. Create a new folder and name it ISIS Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select Drivers and Downloads.

5. Afterwards click on ISIS Software Drivers.

6. Locate the appropriate ISIS driver for your scanner by cross-referencing the scanner

model column on the left to the software column.

7. Double click on the driver file name and the File Download box will popup.

ScanPartner15C\600C\620C\93GX\3091DC\3092DC

Win95\98\ME Installation Procedure

Rev050404A

8. Click on Save and then use the browse (or other folder navigation) button until you

have the ISIS Download folder you created in the Save In Box.

9. Click Save.

10. When completed close the Download Complete window and go to the ISIS

Download folder.

11. Open the folder and you will see the saved ISIS driver file. Double click on the file to

unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

ISIS Download folder, then click on Extract. The file will begin to unzip and when

finished a message box will report the number of files unzipped. Click on OK and

close WinZip.

12. In the ISIS Download folder locate the setup.exe file and double click. Afterwards

follow the prompts and reboot when finished.

Step F: Installing the Twain driver.

1. Create a new folder and name it Twain Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select Drivers and Downloads.

5. Afterwards click on ASPI Twain Software Drivers.

6. Locate the appropriate ASPI Twain driver for your scanner by cross-referencing the

scanner model column on the left to the software column.

7. Double click on the driver file name and the File Download box will popup.

8. Click on Save and then use the browse (or other folder navigation) button until you

have the Twain Download folder you created in the Save In Box.

9. Click Save.

10. When completed close the Download Complete window and go to the Twain

Download folder.

11. Open the folder and you will see the saved ASPI Twain driver file. Double click on

the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and

select the ASPI Twain Download folder, then click on Extract. The file will begin to

unzip and when finished a message box will report the number of files unzipped.

Click on OK and close WinZip.

12. In the ASPI Twain Download folder locate the setup.exe file and double click.

Afterwards follow the prompts and reboot when finished.

Step G: Installing Scandall21.

1. Create a new folder and name it Scandall Download.

2. Next go to our Web page - www.fcpa.com and click on Support & Downloads.

3. In the sub frame under the Product Support column click on Scanners.

4. On the next page select your Drivers and Downloads.

5. Afterwards click on Software Utilities.

6. Double click on the file name and the File Download box will popup.

7. Click on Save and then use the browse (or other folder navigation) button until you

have the Scandall Download folder you created in the Save In Box.

8. Click Save.

9. When completed close the Download Complete window and go to the Scandall

Download folder.

10. Open the folder and you will see the saved Scandall file. Double click on the file to

unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

Scandall Download folder, then click on Extract. The file will begin to unzip and

ScanPartner15C\600C\620C\93GX\3091DC\3092DC

Win95\98\ME Installation Procedure

Rev050404A

when finished a message box will report the number of files unzipped. Click on OK

and close WinZip.

11. In the Scandall Download folder locate the Scandall.exe file and double click.

Afterwards follow the prompts and when finish launch Scandall.

Step H: Scanning with Scandall21.

Once Scandall21 is installed it is time to start scanning.

1. Launch Scandall21 by clicking on the shortcut link on your desktop or manually by

clicking on Start, Programs, Scanner Utility for Microsoft Windows, then

Scandall21.

2. After the Untitled Screen has open, click on Scan and choose Select Source.

3. Select the Fujitsu Twain source for your scanner by Highlighting it and clicking

OK. You will only need to do this once unless you are scanning with multiple

sources.

4. Once you are back at the Untitled Screen click on Scan and select To View this

time. The Twain User Interface will popup.

5. Select the scanning parameters that you wish to use – Color mode, resolution,

paper size, etc…

6. Next under Scan Type choose either ADF or Flatbed in the dropdown box.

7. Place your document in the ADF or on the Flatbed face down and click on the Scan

button.

8. After the document is scanned close the Twain User Interface and the image will

appear on the Untitled Screen.

Congratulations! You have successfully completed your scanner installation.

*If you do not have any unzipping software installed on your system, you can download a free

evaluation copy at www.winzip.com

Autres manuels pour ScanPartner 15C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Scanner

Fujitsu

Fujitsu FI-4990C Manuel

Fujitsu

Fujitsu fi-5015 Manuel utilisateur

Fujitsu

Fujitsu fi-590PRB Manuel

Fujitsu

Fujitsu ScanSnap S1300i Instructions de montage

Fujitsu

Fujitsu FI-6230 Manuel

Fujitsu

Fujitsu fi-6670 Series Manuel utilisateur

Fujitsu

Fujitsu fi-4530C Manuel utilisateur

Fujitsu

Fujitsu fi-4340C Manuel

Fujitsu

Fujitsu fi-6130Z Manuel utilisateur

Fujitsu

Fujitsu ScanSnap iX500 Instructions de montage

Fujitsu

Fujitsu fi-6670 Series Manuel

Fujitsu

Fujitsu M4099D Manuel utilisateur

Fujitsu

Fujitsu Fi-5110EOX2 - ScanSnap! - Document Scanner Guide de référence

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Fujitsu

Fujitsu PA03360-B525 Manuel

Fujitsu

Fujitsu M3093EX Manuel

Fujitsu

Fujitsu C150-E146-02EN Manuel

Fujitsu

Fujitsu ScanSnap S1300 Manuel utilisateur

Fujitsu

Fujitsu S510M - ScanSnap - Document Scanner Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel

Fujitsu

Fujitsu ScanPartner 15C Manuel utilisateur

Fujitsu

Fujitsu FI-6130 Manuel

Fujitsu

Fujitsu FI 4220C - Document Scanner Manuel

Fujitsu

Fujitsu ScanSnap S500 Manuel

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur

Innova

Innova 5210 Manuel utilisateur

Visioneer

Visioneer CardReader 100 Guide de démarrage rapide

Rohde & Schwarz

Rohde & Schwarz TSME6 Manuel utilisateur