Fuji Electric OPC-E2-ADP1 Manuel utilisateur

- 5 -

Option Attachment "OPC-E2-ADP1"

- Please read and ensure a proper understanding of this manual before installing, connecting (wiring), operating, or con-

ducting maintenance and inspection of the interface option.

- Improper handling might result in incorrect operation, a short life, or even a failure of this product as well as the motor.

- Deliver this manual to the end user of this product. The end user should store this instruction manual safely until such time

as the product is disposed of.

Fuji Electric Co., Ltd. INR-SI47-1895-JE

Instruction Manual

- 6 -

Thank you for purchasing the option attachment "OPC-E2-ADP1".

The use of this option attachment allows the FRENIC-Ace series to be equipped with option cards (sold separately).

1. Product Check

Please check the following before using the

product.

(4) Check the model on the nameplate and

ensure that the product is the same as that

ordered.

(5) Ensure that the package contains both the

attachment and accessories.

(6) Ensure that neither the attachment nor

accessories have suffered damage such

as breakage or denting during transport.

Refer to the "1.1 Product configuration"

diagram on the right for details of the

nameplate attachment location and ac-

cessories.

If anything is out of place, or the product ap-

pears to be defective, contact your dealer or

nearest Fuji sales office.

2. Specifications

The applicable scope for this product is as follows.

(1) Applicable models

Series name Inverter capacity

FRENIC-Ace - -

- -

(2) No. of installable option cards: 1

3. Installation Method

Please wait at least 5 minutes after the inverter power has been turned OFF before attempting installation and

wiring.

Also ensure that the touch panel LEDs are OFF, and use a tester to confirm that the DC intermediate circuit volt-

age across main circuit terminals P(+) and N(-) has dropped to a stable value (+25 VDC or lower).

Risk of electric shock

Wire the inverter main circuit terminals and control circuit terminals before installing this attachment.

Step 1

First, wire the inverter main circuit terminals and control circuit terminals.

Step 2

Follow the installation procedure on the next page to install the attachment.

Step 3

Install the option card.

Step 4

Wire the option card to the attachment ground wire and option card terminals.

Secure the wiring near the inverter to prevent the weight of the wiring being applied to the option card.

1.1 Product configuration

Attachment

Harness

Tapping screw

(M3 x 14)

Screw

(M3 x 6)

Nameplate

- 7 -

Installation procedure [Example using option card OPC-DIO]

Ensure that all connectors have been inserted fully and are locked.

(2)

(1)

Open the top cover.

Press the indented locations (indicated

release the lock, allowing the

cover to be opened.

Step (2) details

(3)

(7)

Connect the connector on the

opposite end of the harness to

the attachment connector.

Remove the touch panel.

Remove the bottom cover.

(4)

(5)

Attach the

attachment

to the inverter.

(6)

Connect the harness to

the inverter connector

(larger side of connector).

Pass the harness

through to the inside of

the attachment.

(6)

- 8 -

Fuji Electric Co., Ltd.

Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo, 141-0032, Japan

Phone: +81 3 5435 7058 Fax: +81 3 5435 7420

URL http://www.fujielectric.com/

INR-SI47-1895-JE

If removing the attachment, always disconnect one side of the harness connector beforehand.

Always connect the attachment ground wire to the inverter ground to ground the inverter also.

(8)

Front view of screw tightening loca-

tions

Tighten with tapping screws.

Ti *2

(9)

(10)

Align the option card with the protrusion.

Protrusion

(11)

Tighten the board securing screws. (screws pr

vided with option card)

Attachment

installation

complete

The attachment will be temporarily secured with the

clips on the case, however,

it must be secured

properly with the tapping screws before performing

operation.

The tapping screws may be deformed or damaged if

tightened with more than the specified amount of

torque.

Push the option card down in

the direction

of the arrow to fit the connec

Use the screw (M3 x 6) provided to connect the ground wire to Part A .

*2 Recommended ground wire size: AWG 20 to 16 (0.5 to 1.5 mm2)

(15)

Part A

(13)

(12)

(14)

Table des matières

Autres manuels Fuji Electric Unité de contrôle

Fuji Electric

Fuji Electric EconoPACK+ Guide de l'utilisateur

Fuji Electric

Fuji Electric P633A Series Guide de l'utilisateur

Fuji Electric

Fuji Electric MICREX-SX Series SPH Manuel utilisateur

Fuji Electric

Fuji Electric MICREX-SX series Manuel utilisateur

Fuji Electric

Fuji Electric P642 Series Guide de l'utilisateur

Fuji Electric

Fuji Electric IGBT-IPM X Series Instructions d'utilisation

Fuji Electric

Fuji Electric MT5F33743 Manuel utilisateur

Fuji Electric

Fuji Electric X Series Instructions d'utilisation

Fuji Electric

Fuji Electric M653 Series Guide de l'utilisateur

Fuji Electric

Fuji Electric MICREX-SX Series SPH Manuel utilisateur

Fuji Electric

Fuji Electric Small-IPM Series Instructions d'utilisation

Fuji Electric

Fuji Electric FRENIC-Multi OPC-E1-DEV Manuel utilisateur

Fuji Electric

Fuji Electric ALPHA7 Manuel utilisateur

Fuji Electric

Fuji Electric P633C Series Instructions d'utilisation

Fuji Electric

Fuji Electric P642 Series Instructions d'utilisation

Fuji Electric

Fuji Electric MICREX-SX series Manuel utilisateur

Fuji Electric

Fuji Electric MICREX-SX Series SPH Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur