Freescale Semiconductor S12ZVC Manuel utilisateur

1 Introduction and default

settings

This guide shows how to quickly connect the board to a host

PC and execute a demonstration application preloaded in to

the flash memory.

The S12ZVC MCU integrates:

• S12Z CPU

• Power supply

• PNP external ballast transistor for VDDX, VDDA,

and VDDC

• LED power indicators

• Reset

• LEDs

• Buzzer

• ADC potentiometer

• Keyboard matrix

• High-voltage input

• Sensors

• Temperature and humidity

• Pressure sensor

• Inertial sensor SPI X-Y axis

• SENT

• CAN

• LIN

Default jumper positions of the VLG-S12ZVC board are

shown in the following section.

Freescale Semiconductor Document Number:S12ZVCEBQSG

User Guide Rev 0, 01/2014

S12ZVC Evaluation Board Quick

Start Guide

MagniV Mixed-signal MCUs

by: Jesús Sánchez, Luis Olea

Non-Disclosure Agreement required

Contents

1 Introduction and default settings...............................1

2Device overview S12ZVC family.............................2

3Jumper default configuration.....................................2

4 Software tools installation.........................................4

4.1 Install CodeWarrior development

studio..............................................................4

4.2 Launch the demo program.............................4

5Jumper list and description........................................5

6Headers and connectors list.......................................8

7Peripheral list............................................................9

8References...............................................................10

9 Revision history......................................................10

2 Device overview S12ZVC family

The MC9S12ZVC family is a new member of the S12 MagniV product line integrating a battery level (12 V) voltage

regulator, supply voltage monitoring, high voltage inputs, and a CAN physical interface. It’s primarily targeting at CAN

nodes like sensors, switch panels, or small actuators. It offers various low-power modes and wake-up management to address

state of the art power consumption requirements.

Some members of the MC9S12ZVC family are also offered for high temperature applications requiring AEC-Q100 Grade 0

(-40°C to +150°C ambient operating temperature range). The MC9S12ZVC family is based on the enhanced performance,

linear address space S12Z core and delivers an optimized solution with the integration of several key system components into

a single device, optimizing system architecture and achieving significant space savings.



Figure 1. S12ZVC architecture diagram1

3 Jumper default configuration

This section describes about the jumper configuration.

1. Block Diagram shows the maximum configuration. Not all pins or all peripherals are available on all devices and

packages. Rerouting options are not shown.

Device overview S12ZVC family

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

2 Freescale Semiconductor, Inc.

Non-Disclosure Agreement required

Figure 2. Jumper configuration diagram

The following table lists the jumper default configuration.

Table 1. Jumper default configuration

Header Reference position

J5 1-2

J8 1-2

J10 2-3

J11 1-2

J12 1-2

J13 2-3

J15 1-2

J14 1-2

J20 1-2, 3-4, 5-6, 7-8

J48 1,2

J50 1-2, 3-4, 5-6, 7-8, 9-10, 11-12, 13-14, 15-16

J16 1, 2

J17 1, 2

J18 1, 2

J19 1, 2

J22 1-2, 3-4, 5-6, 7-8

J25 1, 2

J26 1- 2

Table continues on the next page...

Jumper default configuration

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

Freescale Semiconductor, Inc. 3

Non-Disclosure Agreement required

Table 1. Jumper default configuration (continued)

Header Reference position

J29 1- 2

J30 1- 2

J31 1- 2

J35 1- 2

4 Software tools installation

This section describes how to get started with the S12ZVC board by installing CodeWarrior development studio and testing

the demo program that comes programmed with the board.

4.1 Install CodeWarrior development studio

Freescale’s CodeWarrior for MCUs integrates the development tools for several architectures, including the S12Z

architecture, into a single product based on the Eclipse open development platform. Eclipse offers an excellent framework for

building software development environments and is a standard framework used by many embedded software vendors.

The latest version of CodeWarrior for MCUs (Eclipse IDE) can be downloaded from freescale.com/codewarrior.

4.2 Launch the demo program

The S12ZVC EVB board comes preprogrammed with a small demonstration application that exercises the different modules

of the S12ZVC MCU family, including the ADC, SCI, I2C, and GPIO modules.

To see this demonstration:

1. Connect a 12 V power source to the EVB.

2. Connect a USB cable to the USB type B connector.

3. Press the keys on the keypad to hear tones on the buzzer.

4. Tilt the EVB to observe changes on the red and green LEDs.

5. Rotate the potentiometer to observe changes on the orange LED.

6. Notice that the pressure sensor controls the yellow LED.

7. Set up a terminal program to the OSBDM CDC serial port. Set it to a 9600 baud rate and press any key; you will get a

menu to read temperature and humidity from the I2C sensor.

The software for this application is available on freescale.com.

Software tools installation

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

4 Freescale Semiconductor, Inc.

Non-Disclosure Agreement required

5 Jumper list and description

The following table lists all of the jumpers in the S12ZVC evaluation board and its corresponding configuration options.

Table 2. Jumpers description

Jumper Description

J10 HVI Circuit –Reference Voltage Selector

Pin 1-2

Closed

- SW1 is connected to VBAT level. This

provides a HIGH voltage level when

switch SW1 is pressed.

Pin 2-3

Closed

- SW1 is connected to GND level. This

provides a LOW voltage level when

switch SW1 is pressed.

J11 HVI Circuit –Reference Voltage Selector

Pin 1-2

Closed

– SW2 is connected to VBAT level. This

provides a HIGH voltage level when

switch SW2 is pressed.

Pin 2-3

Closed

– SW2 is connected to GND level. This

provides a LOW voltage level when

switch SW2 is pressed.

J12 HVI Circuit –Reference Voltage Selector

Pin 1-2

Closed

– Enable VBAT level to pullup resistor.

This provides a HIGH voltage level when

switch SW2 is open.

Pin 2-3

Closed

– Enable GND level to pullup resistor.

This provides a LOW voltage level when

switch SW2 is open.

J13 HVI Circuit –Reference Voltage Selector

Pin 1-2

Closed

Enable VBAT level to pullup resistor.

This provides a HIGH voltage level when

switch SW2 is open.

Pin 2-3

Closed

Enable GND level to pullup resistor. This

provide a LOW voltage level when

switch SW2 is open.

J14 Buzzer Control

Closing this jumper enables the Buzzer control by PP7 port.

J15 Buzzer Power

Closing this jumper powers the Buzzer circuit.

J16 VDDX External Ballast Transistor

With this jumper closed, the VSUP Voltage is connected to PNP external transistor

collector for the VDDX voltage regulation.

J17 VDDX External Ballast Transistor

This jumper enables the signal control of the PNP external transistor collector for

the VDDX voltage regulation.

J18 VDDC External Ballast Transistor

Table continues on the next page...

Jumper list and description

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

Freescale Semiconductor, Inc. 5

Non-Disclosure Agreement required

Table 2. Jumpers description (continued)

Jumper Description

With this jumper closed, the VSUP Voltage is connected to PNP external transistor

collector for the VDDC voltage regulation.

J19 VDDC External Ballast Transistor

This jumper enables the signal control of the PNP external transistor collector for

the VDDC voltage regulation.

J2 Humidity and temperature sensor power

Closing this jumper powers the humidity and temperature sensor.

J20 LEDs

Pin 1-2

Closed

Red LED is connected to PP6 port

Pin 3-4

Closed

Green LED is connected to PP5 port

Pin 5-6

Closed

Yellow LED is connected to PP4 port

Pin 7-8

Closed

Orange LED is connected to PP0 port

J22 Power Supply Voltages – LEDs Indicators

Pin 1-2

Closed

Enable VDDC - LED indicator

Pin 3-4

Closed

Enable VDDA - LED indicator

Pin 5-6

Closed

Enable VDDX - LED indicator

Pin 7-8

Closed

Enable VSUP - LED indicator

J25 VDDC External Ballast Transistor - Output

Closing this jumper connects the external PNP ballast transistor output to

VDDC_OUT line.

J26 VDDX External Ballast Transistor - Output

Closing this jumper connects the external PNP ballast transistor output to

VDD_OUT line.

J29 VDDA Power

Closing this header connects VDDA to VDD_OUT line.

J3 Humidity Temperature Sensor - Communication

Closing this jumper connects the SCL-line of the Humidity Temperature Sensor to

PT1.

J30 VDDX

Closing this jumper connects VDDX to VDD_OUT line.

J31 VDDC

Closing this jumper connects VDDC to VDDC_OUT line.

Table continues on the next page...

Jumper list and description

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

6 Freescale Semiconductor, Inc.

Non-Disclosure Agreement required

Table 2. Jumpers description (continued)

Jumper Description

J32 SENT Transmitter Interface

Closing this header connects the SENT_TX line to SENT transmitter interface

circuit.

J35 LIN Mode

With this jumper, the user can configure the local and remote wake-up mode of

MC33662 - LIN transceiver.

J38 LIN and SENT Communication

Pin 1-2

Closed

PS4 is connected to LIN_RX

Pin 3-4

Closed

PS5 is connected to LIN_TX

Pin 5-6

Closed

PS7 is connected to SENT_TX

J4 Humidity Temperature Sensor - Communication

Closing this jumper connects the SDA line of the humidity temperature sensor to

PT0.

J41 LIN – Master/Slave Mode

With this jumper, the user can configure as master or slave mode.

J42 INERTIAL Sensor Power

Closing this jumper powers the INERTIAL sensor circuit.

J44 CAN

Closing this jumper connects the SPLIT pin to the resistors termination of CAN.

J47 Press Sensor Power

Closing this jumper powers the press sensor circuit.

J48 Potentiometer Reference

Closing this jumper connects the potentiometer to VDDA.

J5 VBAT

Closing this jumper connects VBAT to all system.

J50 Pin 1-2

Closed

Closing this jumper connects PAD8 port

to the potentiometer.

Pin 3-4

Closed

Closing this jumper connects PAD9 port

to Press Sensor – Output.

Pin 5-6

Closed

Closing this jumper connects PAD10

port to the keyword matrix.

Pin 7-8

Closed

Closing this jumper connects PAD11

port to the keyword matrix.

Pin 9-10

Closed

Closing this jumper connects PAD12

port to the keyword matrix.

Pin 11-12

Closed

Closing this jumper connects PAD13

port to the keyword matrix.

Table continues on the next page...

Jumper list and description

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

Freescale Semiconductor, Inc. 7

Non-Disclosure Agreement required

Table 2. Jumpers description (continued)

Jumper Description

Pin 13-14

Closed

Closing this jumper connects PAD14

port to the keyword matrix.

Pin 15-16

Closed

Closing this jumper connects PAD15

port to the keyword matrix.

J51 VDDX shunt resistor

Closing this jumper enables a shunt resistor on VDDX that can aid on current

measurements for the VDDX ballast transistor.

J52 VDDC shunt resistor

Closing this jumper enables a shunt resistor on VDDC that can aid on current

measurements for the VDDC ballast transistor.

J8 LEDs Power

Closing this jumper connects VDDX to D4, D6, D13, and D15.

6 Headers and connectors list

The following table lists all of the connectors available in the S12ZVC evaluation board and their corresponding signals.

Table 3. Connectors description

Header / Connector Description

J1 Main power connector (up to 18 V)

J21 VBAT, VSUP, VDDX, VDDC, and VDDA are connected to this

header.

J23 HVI Header – External HVI signal

This jumper allows a monitoring/measurement of the High

voltage signal. If J13 and J10 are disabled, the user can apply

an external signal. This jumper (pin 1-2) should always be

OPEN.

J24 HVI Header – External HVI signal

This jumper allows a monitoring/measurement of the High

voltage signal. If J11 and J12 are disabled, the user can apply

an external signal. This jumper (pin 1-2) should always be

OPEN.

J27 GPIO Header - Port T

J28 SENT transmitter header with GND

J33 GPIO Header - Port P

J34 BDM Connector

J37 LIN Connector

J39 GPIO Header - Port AD

J40 GPIO Header - Port S

J45 CAN main connector

Table continues on the next page...

Headers and connectors list

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

8 Freescale Semiconductor, Inc.

Non-Disclosure Agreement required

Table 3. Connectors description (continued)

Header / Connector Description

J46 CAN main connector

J49 OSBDM USB port for programming and debugging the main

MCU.

J6 VDDX - PNP Ballast Transistor Terminals

The header could be used for measurements/monitoring of all

signals of the external PNP ballast transistor: Base, Collector,

and Emitter. Opening J16, J17, and J27 connects the user to

an additional transistor for validation.

J7 VDDC – PNP Ballast Transistor Terminals

The header could be used for measurements/monitoring of all

signals of the external PNP ballast transistor: Base, Collector,

and Emitter. Opening J18, J19, and J25 connects the user to

an additional transistor for validation.

J9 Main power connector (up to 18 V)

7 Peripheral list

The following table lists all the peripherals available in the S12ZVC evaluation board.

Table 4. Peripheral description

Peripheral ID MCU PORT Description

Potentiometer R76 PAD8 Potentiometer connected to

ADC channel 8

LED – Voltage Indicator D7 - VSUP LED indicator

D10 - VDDX LED indicator

D14 - VDDA LED indicator

D16 - VDDC LED indicator

Switch Panel SW4 - Matrix keyboard switch

SW5 -

SW6 -

SW7 -

SW8 -

SW9 -

SW10 -

SW11 -

SW12 -

High Voltage Switch SW1 PL1 Switch connected to PL1 (with

10 kΩresistor)

SW2 PL0 Switch connected to PL0 (with

10 kΩresistor)

Table continues on the next page...

Peripheral list

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

Freescale Semiconductor, Inc. 9

Non-Disclosure Agreement required

Table 4. Peripheral description (continued)

Peripheral ID MCU PORT Description

Buzzer LS1 PP7 Buzzer controlled by PP7

LED – General purpose D4 PP6 Red LED connected to port

PP6

D6 PP5 Green LED connected to port

PP5

D13 PP4 Yellow LED connected to port

PP4

D15 PP0 Orange LED connected to

port PP0

Reset SW3 - Reset switch

8 References

For further reference, the following documents are available at freescale.com.

1. AN4851: Using the High Resolution Timer and PWM in the S12ZVC (AN4851)

2. AN4852: Using the SENT Transmitter Module in S12ZVC Devices (AN4852)

9 Revision history

Revision number Date Substantial changes

0 01/2014 Initial release

References

S12ZVC Evaluation Board Quick Start Guide, Rev 0, 01/2014

10 Freescale Semiconductor, Inc.

Non-Disclosure Agreement required

Table des matières

Autres manuels Freescale Semiconductor Carte mère

Freescale Semiconductor

Freescale Semiconductor QorIQ LS1043A Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor MPC5748G EVB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor Qorivva MPC5746R-176DS Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor kinetis TWR-SMPS-LVFB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor FRDM-17C724-EVB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT33926PNBEVBE Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor IB112 Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor DEMO908GZ60 Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT33908MBEVBE Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor M68EVB912C32 Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor Qorivva MPC5746R-176DS Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT33814AEEVBE Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT33912EVME Manuel

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KE15Z Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor TWR-K20D72M Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT34825EPEVME Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT33932VWEVBE Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor MC13853 LNA Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor KIT22XS4200EKEVB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor MPC566EVB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor MPC5777C EVB Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor PowerQUICC MPC885 Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor M5407C3 Manuel utilisateur

Freescale Semiconductor

Freescale Semiconductor MC13892 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur