Fortinet Talkswitch TS-850i Mode d’emploi
ANSWERS WITH INTELLIGENCE®
TALKSWITCH®START GUIDE
TALKSWITCH
TS-850i AND
TS-860i TELEPHONE
CT.TP005.010903
Copyright ©2011 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®,
FortiGuard®, FortiCare®, FortiManager®, FortiAnalyzer®, and TalkSwitch®
are registered trademarks of Fortinet, Inc. and other Fortinet names
herein may also be registered trademarks and/or common law trademarks
of Fortinet. Other product or company names may be trademarks of their
respective owners.
Reproduction, adaptation or translation without prior written permission
is prohibited, except as allowed under the copyright laws.
Information in this start guide is subject to change without notice and
does not represent any commitment on the part of TalkSwitch. No part
of this start guide may be reproduced or transmitted in any form or by
any means, electronic or mechanical (including photocopying, recording,
or information storage and retrieval systems) or translated to another
language, for any purpose other than the licensee’s personal use and as
specifically allowed in the licensing agreement, without the express
written permission of TalkSwitch.
CT.TP005.010903
May 2011
EVERY CALL COUNTS 1
Introduction
Congratulations on your purchase of the TS-850i/TS-860i
Cordless DECT Phone!
This guide describes how to install and configure your new
telephone with a TalkSwitch system. For more information,
see the support section at http://global.talkswitch.com.
Installing the base
1. Place the base near a wired Ethernet router, either
on a tabletop or mounted on a wall. Avoid placing
the base in a location with a lot of metal, or near
devices that cause interference.
2. Connect the Ethernet cable from the WAN port on
the base to a LAN port on your router or Ethernet
switch. The TalkSwitch unit must be connected to
the same LAN.
TS-850i base
2 TS-850i AND TS-860i START GUIDE
3. Optionally connect the telephone cable from the
Line port on the base to the telephone wall socket.
This will allow you to use the TS-850i/TS-860i as a
regular phone as well.
4. Connect the power adapter from the power outlet to
the power supply connector.
EVERY CALL COUNTS 3
Installing the handset charger
1. Place the handset charger within the signal range of
the base. The handset has an indoor signal range of
up to 150 feet (50 meters) from the base. Concrete
and metal objects might affect the signal range.
2. Connect the power adapter from the power outlet to
the power supply connector.
TS-860i charger
4 TS-850i AND TS-860i START GUIDE
Installing the batteries
1. Release the battery cover from the bottom.
2. Insert the Li-ion cell battery in the handset, making
sure it is placed as shown in the illustration, and
then slide the battery cover shut.
TS-860i handset
EVERY CALL COUNTS 5
Charging the batteries
1. Place the handset in the handset charger. The
handset turns on, and the battery charge indicator
in the display starts to flash.
2. Charge the batteries for at least 10 hours before
first use.
6 TS-850i AND TS-860i START GUIDE
Registering handsets with the base
1. Press the Reset button on the back of the base. A
five-minute registration period starts, which allows
handsets to register with the base.
NOTE: If you have multiple bases, only reset one base
at a time, and wait five minutes before resetting the
next base.
2. If the handset is turned off, press the Red Phone
key to turn it on.
3. Place the handset in the handset charger. The handset
automatically registers with the base, and the Configure
SIP Domain message appears on the display. This
message indicates that you must configure the TS-850i/
TS-860i as an IP extension, as described later.
A base can support up to three handsets with three
concurrent calls. It can support up to eight handsets if
they aren’t all used at once. If you have more than
three handsets and are getting busy signals, add more
bases to your installation in order to handle more calls.
EVERY CALL COUNTS 7
Once the handset is registered, the left connection
status indicator in the display will turn yellow.
4. Once the handset is registered, you can place
additional handsets in the handset charger for
registration. If the five-minute registration period
has expired, but the handsets aren’t all registered,
press the Reset button on the back of the base to
start a new registration period.
8 TS-850i AND TS-860i START GUIDE
Configuring the TS-850i/TS-860i as an IP extension
You can configure the phone as an IP extension located
within the office, or outside the office (i.e. an external
IP extension).
Before configuring a phone, ensure that no handsets
registered with the associated base are being used. If a
handset is on a call, the call will be terminated when the
system resets the base during configuration of the phone.
NOTE: The TS-850i requires version 6.11 or greater of the
TalkSwitch management software. The TS-860i requires
version 6.50 or greater, which is available in the support
section at http://global.talkswitch.com.
Ce manuel convient aux modèles suivants
1
Autres manuels Fortinet Téléphone
Fortinet
Fortinet FortiVoice Enterprise 100E Manuel utilisateur
Fortinet
Fortinet FON-350i Manuel utilisateur
Fortinet
Fortinet FortiFone FON-360i Manuel utilisateur
Fortinet
Fortinet FortiFone FON-C71 Manuel utilisateur
Fortinet
Fortinet FortiVoice Manuel de service
Fortinet
Fortinet FortiFone FON-460i Manuel utilisateur
Fortinet
Fortinet FON-600 Mode d’emploi
Fortinet
Fortinet FON-350i Mode d’emploi
Fortinet
Fortinet FortiFone FON-450i Manuel utilisateur
Fortinet
Fortinet FortiVoice 50E6 Manuel utilisateur
Fortinet
Fortinet FON-860i Manuel utilisateur
Fortinet
Fortinet FortiFone-350i Manuel utilisateur
Fortinet
Fortinet FortiFone FON-450i Mode d’emploi
Fortinet
Fortinet FortiVoice Enterprise 1000E Manuel utilisateur
Fortinet
Fortinet FON-600 Manuel utilisateur
Fortinet
Fortinet FortiFone FON-470i Manuel utilisateur
Fortinet
Fortinet FortiFone FON-C75 Manuel utilisateur
Fortinet
Fortinet FON-370i Manuel utilisateur
Fortinet
Fortinet FortiFone FON-H25 Manuel utilisateur
Fortinet
Fortinet FON-350i Manuel utilisateur
