Fluke TS54 Manuel utilisateur

Toner and SmartTone Function

The toner helps you identify wire pairs and find

cables in bundles, at patch panels, or behind

walls.

Connect the test leads to two wires in a cable.

Press M, then select SmartTone. Use a tone

probe to find the place where the tone is the

loudest.

If there is voltage on the line, the display shows

SmartTone Volt Detect Lock Out, and toner will

not operate.

The SmartTone function helps you make sure

you correctly identify a wire pair. When you put

a short on the correct pair, the tone changes.

Standard VOPs

Press M, select TDR, then select VOP Setting.

VOP Twisted Pair Cable Types

68 Gel Filled19 AWG

64 Gel Filled 22 AWG

62 Gel Filled 24 AWG

60 Gel Filled 26 AWG

68 Paper 22 AWG

66 Paper 24 AWG

65 Paper 26 AWG

72 PIC 19 AWG

67 PIC 22 AWG

66 PIC 24 AWG (default)

64 PIC 26 AWG PN 3836378

August 2011, Rev. 3 2/2017

Data Test / Lockout Override

Connect the test set to Tip and Ring. Press P.

If data is present, a warning beep sounds, and

the test set does not go off-hook, and the

display shows Data Detect Lockout. To go off-

hook, press $.

Polarity

+: The polarity of Tip and Ring is reversed.

Redial the Last Number Dialed

Press P. Press L.

Speed Dial a Stored Number

Press P. Press R. Press the key ( 1through 9 )

of the memory location where the number is

stored.

Volume

Press CDto adjust the volume of the

speaker that is on.

Press M. To scroll, press CD. To select an

item or save a setting, press Magain. To exit,

select Back or press Q.

•Contacts: A phonebook of nine stored numbers

for the speed dialing function. The number in

memory location 9 is the number for the ANAC

function.

TS®54 TDR Test Set Users Card

•Call Log: A list of phone numbers for the last 10

calls that the test set made or received.

•Digit Grab: Shows you the digits dialed by

another device.

•SmartTone: Lets you use an inductive probe to

find telephone lines.

•EditContact: Lets you edit numbers in the

phonebook.

•TDR: Lets you change the Line Verification and

VOP settings for the TDR.

•Settings:

•Bklt Time: Backlight timeout

•Handset Vol, Spkr Vol: Handset and speaker

volume.

•Tone/Pulse: Select tone or pulse mode

•Pause Time Flash Time: Duration for pause and

flash.

•SpkrPhone: Default mode for the speakerphone.

Two-Way: microphone is on.

RecivOnly: microphone is off.

•AutoShutOff: Power-down timeout.

•FactDfaults: Select factory defaults.

Visual ANAC mode (For service provider use only.

Visual ANAC is not available in all regions.)

Connect the test set to a working telephone

line. Press P. Press R$. The display shows

Dial ANAC. Dial the ANAC number.

If you put the ANAC number into location 9 in

the Call Phonebook, the test set goes into visual

ANAC mode and dials the ANAC number when

you press R9.

Caller ID Messages

• The incoming phone number

•Blocked ID: CID is blocked

•Line error: CID data is incomplete

•Unknown ID: CID is not available

TDR

The TDR lets you measure the length of cables

and the distance to the first open or short on

cables as long as 3,000 ft (914 m). Optional: Turn

on the Line Verification (Line Verif) function

and set the velocity of propagation (VOP) to the

correct value for the cable. The Line Verification

function does tests for data and voltage on the

line when you press t.

Press Q. Connect the test leads to the cable.

Press t.

TDR Results

•Short at 1267 ft: There is a short across the two

conductors 1267 feet from the test set.

•Open at 2433 ft: The cable is 2433 feet long, or

there is an open in one or both of the

conductors 2433 feet from the test set.

•TDR Voltage Detect Lockout: There is data or

voltage on the line. The TDR does not operate

on an active line.

Autres manuels Fluke Équipement de test

Fluke

Fluke 150 Series Manuel d'utilisation et d'entretien

Fluke

Fluke HART 744 Manuel utilisateur

Fluke

Fluke 719-100G Manuel d'instructions

Fluke

Fluke 725 Instructions d'utilisation et de sécurité

Fluke

Fluke 975 AirMeter Instructions d'installation et d'utilisation

Fluke

Fluke T5-600 Manuel utilisateur

Fluke

Fluke 712 Manuel utilisateur

Fluke

Fluke T6-600 Manuel utilisateur

Fluke

Fluke MP1 Manuel utilisateur

Fluke

Fluke 1535 Manuel d'utilisation et d'entretien

Fluke

Fluke 525A Manuel utilisateur

Fluke

Fluke 1AC II VoltAlert Manuel utilisateur

Fluke

Fluke OF-500-01 OptiFiber Manuel d'utilisation et d'entretien

Fluke

Fluke 718 1G Instructions d'utilisation et de sécurité

Fluke

Fluke 725Ex Manuel utilisateur

Fluke

Fluke 712C Manuel utilisateur

Fluke

Fluke CombiScope PM3370B Manuel utilisateur

Fluke

Fluke 741B Manuel utilisateur

Fluke

Fluke 724 Manuel d'utilisation et d'entretien

Fluke

Fluke CableIQ CIQ-100 Manuel utilisateur

Fluke

Fluke Fiber Viewer FT120 Manuel utilisateur

Fluke

Fluke 1623 Manuel utilisateur

Fluke

Fluke CombiScope PM3370B Manuel utilisateur

Fluke

Fluke 725Ex Manuel d'utilisation et d'entretien

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur