Fluke T5-600 Manuel utilisateur
PN 1629509 (English) July 1997, Rev. 2, 9/01
© 2001 Fluke Corporation, All rights reserved. Printed in U.S.A.
®
T5-600/T5-1000
Electrical Tester Instruction Sheet
W
Read First: Safety Information
If this product is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.
W
Warning
•Do not use the tester if it is damaged or operating abnormally.
Protection may be impaired.
•Before each use:
•Make sure the battery door is closed and latched.
•Inspect the tester and test leads. Look for cracks, missing
plastic, exposed metal, or damaged insulation. Replace
damaged test leads before using the tester.
•Verify the tester’s operation by measuring a known voltage.
•Replace the batteries as soon as the low battery indicator (
M
)
appears.
•Do not use the tester around explosive gas, vapor or dust.
•Do not apply more than the rated voltage, as marked on the
tester, between terminals or between any terminal and earth
ground.
•Refer servicing to qualified personnel.
•Use caution when working above 30 V ac rms, 42 V ac peak, or
60 V dc.
•When using the probes, keep your fingers behind the finger
guards on the probes.
•Connect the common test lead before you connect the live test
lead. Disconnect the live test lead first.
•The display will not display hazardous voltages in display hold.
The voltage indicator LED ( ) continues to operate.
Symbols
BAC (alternating current) JEarth ground
FDC (direct current) TDouble insulated
MBattery
WCaution, risk of danger
(refer to the manual.) XCaution, shock hazard
Voltage Indicator
While the tester is on, the LED glows when more than 30 V ac or 60 V
dc is present across the leads. (The LED can also glow at lower
voltages.) Be aware that such voltages pose a shock hazard.
Measuring Voltage
(V)
The tester automatically selects dc (DC) or ac (AC) voltage mode based
on the peak values of the measured signal.
The tester defaults to ac voltage when turned on.
DC Voltage
T5-600 maximum: 600 V CAT III
T5-1000 maximum: 1000 V, also
600 V CAT IV
AC Voltage
45 Hz to 66 Hz
T5-600 maximum: 600 V rms
T5-1000 maximum: 1000 V rms,
also 600V rms CAT IV
DC
AC
V
AC/DC
Automatic
Selection
V
AC/DC
Automatic
Selection
ex2.eps
Measuring Continuity and Resistance
(Ω)
Continuity Resistance
1000 Ω
Range
Greater than
400 Ω
Open Short
Less than
25 Ω
ex3.eps
Beeper indicates shorts lasting 10 ms (1/100 second) or longer.
Measuring AC Current
(A)
0.5"(12.9 mm)
maximum
A
AC
ex1.eps
•Range: 0 A to 100.0 A;
45 Hz to 66 Hz
•
W
Do not connect test
probes to voltages while
measuring current.
•Place conductor
anywhere within the
sensor zone (shaded
area shown below).
OKOK
OK OK
Sensor
Zone
ex5.eps
Display Hold
To hold the reading on the display, press and release HOLD. The
display will not display hazardous voltages in display hold. The voltage
indicator LED ( ) continues to operate.
To exit the display hold mode, press and release HOLD again, or turn
the rotary switch to a new position.
Automatic Power Down
The tester turns off automatically if you do not turn the rotary switch or
press HOLD for approximately 45 minutes. To resume operation, turn
the tester off, then turn the tester on.
Low Battery Indicator
M
W
Warning
To avoid false readings, which could lead to possible
electric shock or personal injury, replace the battery as
soon as the low battery indicator (
M
)appears.
Maintenance
Clean the case with a damp cloth and detergent. Do not use abrasives
or solvents.
Because the inputs are electronically protected, no fuses are required.
Battery Replacement
Observe the polarity markings inside the battery compartment.
+
+
Do not
overtighten screw
Disconnect probes
from Voltage
Switch OFF
2 AA
+
+
ex4.eps
Replacement Parts
Test Lead Assembly.
Replace only with Fluke double-insulated leads (
T
)
See "Accessories" for available probes.
PN 648029
Battery Door PN 1626588
Battery Door Screw PN 1618578
Accessories
H5 Belt Holster
TP1 Probe Set, Flat-Blade
TP4 Probe Set, 4 mm round
Service Information Sheet
, PN 686953
To contact Fluke, call:
USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-678-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Visit Fluke’s Web site at www.fluke.com.
Specifications
Specifications subject to change without notice.
Calibration: One-year calibration cycle.
Maximum Voltage Between any Terminal and Earth Ground:
T5-600: 600 V rms, Overvoltage Category III; Pollution Degree 2
T5-1000: 1000 V rms, Overvoltage Category III, also 600 V rms
overvoltage Category IV, Pollution Degree 2
Maximum Voltage between Current Fork and Earth Ground: T5-600
and T5-1000: 1000 V rms, Overvoltage Category III, also 600 V rms,
Overvoltage Category IV, Pollution Degree 2, (This dual rating applies
to the current fork only.)
Temperature: Operating: -10 °C to +50 °C (14 °F to 122 °F);
Storage: -30 °C to +60 °C (-22 °F to +140 °F)
Altitude: Operating: 2000 m (6562 ft); Storage: 10,000 m (32808 ft)
Relative Humidity: 0 % to 95 %, 5 °C to 30 °C (41 °F to 86 °F); 0 % to
75 %, 30 °C to 40 °C (86 °F to 104 °F); 0 % to 45 %, 40 °C to 50 °C
(104 °F to 122 °F)
Battery Type and Life: AA (2); 360 hours continuous with alkaline;
125 hours continuous with zinc chloride
Shock, Vibration: 1 m drop at -10 °C to 50 °C (14 °F to 122 °F) per
ANSI/ISA-S82.01-1994 and EN 61010-1: 1995. Random vibration per
MIL-PRF-28800F for a Class 2 instrument (5 Hz to 55 Hz, 3 g
maximum).
Surge Protection: T5-600 6 kV per IEC 61010;
T5-1000 8 kV per IEC 61010
Enclosure Rating: IP 52 per IEC 60529, no vacuum applied
RF Field Specification: 0.5 % full scale + (specified accuracy) at
3 V / m
Safety: Complies with ANSI/ISA-S82.01-94, UL classified to IEC
61010, CSA/CAN C22.2 No.1010.1-92, and EN 61010-1: 1995.
EMC: EN 61326
Certifications: In accordance with
IEC 61010-1 54CJ
Accuracy is specified for 1 year after calibration, at 18 °C to 28 °C
(64 °F to 82 °F) with relative humidity to 90 %. AC conversions are ac-
coupled, average responding, and calibrated to the rms value of a sine
wave input.
Accuracy specifications are given as follows:
±( [ % of reading] + [number of least significant digits] )
Temperature coefficient of 0.1 x (specified accuracy) / °C for <18 °C
or >28 °C (< 64.4 °F or > 82.4 °F)
Function T5-600
Range T5-1000
Range Reso-
lution Accuracy
K
600 V rms 1000 V rms 1 V ±(1.5 % + 2 digits)
L
600 V 1000 V 1 V ±(1 % + 1 digit)
?
100.0 A 100.0 A 0.1 A ±(3 % + 3 digits)
e
1000 Ω1000 Ω1 Ω±
(1 % + 2 digits)
Input Protection
Function T5-600 T5-1000
Input Impedance
(nominal)
K
600 V rms 1000 V rms 1 MΩ, <100 pF ac-coupled
L
600 V rms 1000 V rms 1 MΩ, <100 pF
e
600 V rms 1000 V rms ---
Function Open Circuit Test
Voltage Short Circuit
Current
e
1.65 V dc (nominal) <0.6 mA
CAT III protects against transients in a
fixed equipment installation
such
as a distribution panel, and lighting systems in large buildings.
CAT IV protects against transients from a
primary supply
such as an
electricity meter or an overhead or underground utility service.
Limited Warranty & Limitation Of Liability
This Fluke product will be free from defects in material and
workmanship for two years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage
from accident, neglect, misuse or abnormal conditions of operation
or handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. To obtain service during the warranty
period, send the defective product to the nearest Fluke Authorized
Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM
ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
10/96
Autres manuels pour T5-600
5
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fluke Équipement de test
Fluke
Fluke 1550C Manuel utilisateur
Fluke
Fluke 5730A Manuel de la liste des pièces
Fluke
Fluke 714 Manuel utilisateur
Fluke
Fluke 522A/6 Manuel utilisateur
Fluke
Fluke Hydra Series II Manuel utilisateur
Fluke
Fluke FEV300 Instructions originales
Fluke
Fluke 730G Manuel utilisateur
Fluke
Fluke T100 VDE Manuel utilisateur
Fluke
Fluke 741B Manuel utilisateur
Fluke
Fluke 5080A Manuel de la liste des pièces
Fluke
Fluke 718Ex Manuel utilisateur
Fluke
Fluke AIRCHECK Manuel d'instructions
Fluke
Fluke MicroScanner MS-POE Manuel utilisateur
Fluke
Fluke Hart Scientific 9101 Manuel utilisateur
Fluke
Fluke DTX-PCU6S Manuel utilisateur
Fluke
Fluke 190 Series II Manuel utilisateur
Fluke
Fluke P3800 Series Manuel utilisateur
Fluke
Fluke P3860-MPA Manuel utilisateur
Fluke
Fluke i6000s Flex-24 Manuel utilisateur
Fluke
Fluke 705 Manuel utilisateur
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Mercury
Mercury TSL01 Manuel utilisateur
