Fluke 55XXA Manuel utilisateur

Introduction

This document provides instructions for the 55XXA Portability Kit (the Kit).

Use the Kit to replace the original 5560A, 5550A, and 5540A Calibrator handles. The Kit

replacement handles provide greater product protection and add more hand holds to make

the Product easier to lift. The display cover/pouch protects the front panel and can hold

assorted test leads or other items.

Figure 1. 55XXA Portability Kit (Installed)

55XXA

Portability Kit

Instructions

PN 5310593

April 2022

All product names are trademarks of their respective companies.

55XXA

Instructions

Contact Fluke Calibration

Fluke Corporation operates worldwide. For local contact information, go to our website:

www.flukecal.com

To register your product, view, print, or download the latest Users Manual or manual supplement,

go to our website.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

+1-425-446-5500

[email protected]

Kit Contents

Check to make sure that all of the listed parts are included:

Assemble the Handles

Attach the 2 side handles to the 4 corner handles. See Figure 2. For each pair of corner

handles, use a Phillips screwdriver to tighten 2 M5X10 screws (torque to 12.5 in-lbs) and 2

strap washers to screw a side handle to the center of each of the corner handles. Once

assembled, set the handles aside.

Figure 2. Side Handle and Handle Assembly

• (4) Corner Handles

•(2)SideHandles

•(4)CrossBars

• (16) M3x8 Cross Bar Screws

• (20) M4x10 Handle Screws

• (4) M5x10 Screws

•(4)StrapWashers

• (1) Display Cover/Pouch with Straps

•(4)TopandBottomDisplayCover/

Pouch Straps.

M5X10 Screw

Strap Washer

Corner Handle

Side Handle

Portability Kit

Installation

When you install the Kit on the Product, do not remove too many screws from the Product at

once. To do so can cause the Product covers to shift and make the Product come apart.

To install the Kit on the Product, See Figure 3:

1. Turn off the Product and remove the mains power cord.

2. Place the Product on a flat surface.

3. Start with one side (left or right). Use a 3 mm hex wrench to remove the side front and rear

handles (each handle has 5 screws).

4. With the M4x10 screws, attach one of the handle assemblies to the Product. Use screw

holes that held the standard handles. Use five screws for each handle. All 20 M4 handle

screws require a Torx T20 drive. Tighten to a torque of 12.5 in-lbs.

5. Attach the top-panel rear cross bar to the Product. See Figure 3:

a. On the rear of the Product top-panel, use a Phillips screwdriver to remove the four

screws. Do not remove the screws from the top-panel front side yet.

b. With the slots of the cross bar facing out, slide one end tab of the cross bar into the

hole on the corner handle.

c. Use four M3X8 screws to attach the cross bar to the top rear of the Product. The four

cross bar screws require a Phillips bit. Torque of 8 in-lbs.

Note

Start each of these screws but wait to tighten until all are started.

Figure 3. Attach the Cross Bar to the Handle and Top of the Product

Cross Bar

(4) M3X8 Screws

55XXA

Instructions

6. The steps to attach the top-panel front cross bar are similar to attach the top-panel rear

cross bar. However, it is easier to attach the cover/pouch to the cross bar first. See

Figure 4.

a. With the Fluke logo on the display cover/pouch facing you and right-side up, thread the

ends of the two top straps through the top slots at of the cross bar.

b. Loop the ends around the cross bar and secure the ends to the top of the straps with

the hook and loop fasteners.

c. Once the straps are attached to the cross bar, attach the top-panel front cross bar to

the top of the Product. Remove the screws and replace the cross bar. Make sure the

pouch straps are at the front.

Figure 4. Loop Straps Through Cross Bars

7. Turn the Product upside down.

8. Attach the bottom-panel rear cross bar to the bottom of the Product. Remove the screws

and replace the cross bar.

9. The steps to attach the bottom-panel front cross bar are similar to the steps to attach the

top-panel front cross bar. Attach the last two display cover/pouch straps to the cross bar

first. See Figure 4.

10. Once the straps are attached to the cross bar, make sure the cross bar slots face towards

the front of the product and attach the bottom-panel front cross bar as you attached the

top-panel front cross bar.

11. With the M4x10 screws, attach the other corner handle assembly to the other side of the

Product using the screw holes from the standard handles. Use five screws for each handle.

Use a Torx T20 driver and torque to 12.5 in-lbs.

12. Make sure that all screws are tightened.

13. Place the Product right-side up, restore the power cable, and connect to power. The

Product is ready use.

Front Cross Bar

Display Cover/Pouch Straps

Table des matières

Autres manuels Fluke Équipement de test

Fluke

Fluke TS22A Manuel utilisateur

Fluke

Fluke 712C Manuel utilisateur

Fluke

Fluke CertiFiber Manuel utilisateur

Fluke

Fluke 9103 Manuel utilisateur

Fluke

Fluke 9040 Manuel du propriétaire

Fluke

Fluke T3 Manuel d'utilisation et d'entretien

Fluke

Fluke 6200-2 Manuel utilisateur

Fluke

Fluke TS 42DLX Manuel utilisateur

Fluke

Fluke 80PK-27 Manuel utilisateur

Fluke

Fluke 1503 Manuel utilisateur

Fluke

Fluke MicroScanner Series Manuel utilisateur

Fluke

Fluke DTX-PC S Series Manuel utilisateur

Fluke

Fluke NETWORK SERVICE MODULE DTX-NSM Manuel utilisateur

Fluke

Fluke 709 Manuel utilisateur

Fluke

Fluke FEV100 Manuel utilisateur

Fluke

Fluke 80T-150U Manuel utilisateur

Fluke

Fluke 716 Manuel utilisateur

Fluke

Fluke 714 Manuel utilisateur

Fluke

Fluke TS 44 PRO Manuel de la liste des pièces

Fluke

Fluke 6270A Manuel utilisateur

Fluke

Fluke T+ Manuel d'utilisation et d'entretien

Fluke

Fluke NetTool Manuel utilisateur

Fluke

Fluke DTX-PCU6S Manuel utilisateur

Fluke

Fluke 368 FC Guide de référence

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur