Fluke 80i-2010s Manuel utilisateur

PN 5130594 June 2019

All product names are trademarks of their respective companies.

80i-2010s

AC/DC Current Clamp

Instructions

Introduction

Use the Fluke 80i-2010s AC/DC Current Clamp (the Clamp or Product)

with oscilloscopes and digital multimeters and power analyzers for

accurate non-intrusive measurements of ac, dc, and complex waveform

currents.

Using advanced Hall Effect technology, the Clamp can accurately

measure currents up to 2000 A RMS. These features make it a powerful

tool for use in inverters, switch mode power supplies, industrial

controllers, automotive diagnostics, and other applications requiring

current measurements and/or waveform analysis.

Table 1 shows the Clamp.

How to Contact Fluke

To contact Fluke, call one of the following telephone numbers:

• Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)

• Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)

• Canada: 1-800-36-FLUKE (1-800-363-5853)

• Europe: +31 402-675-200

• Japan: +81-3-6714-3114

• Singapore: +65-6799-5566

• China: +86-400-921-0835

• Brazil: +55-11-3530-8901

• Anywhere in the world: +1-425-446-5500

Or, visit Fluke's website at www.fluke.com

To view, print, or download the latest manual supplement, visit

http://us.fluke.com/usen/support/manuals.

Go to www.fluke.com to register your product and find more information.

Safety

A Warning identifies conditions and procedures that are dangerous to the

user.

XW Warning

To prevent possible electrical shock, fire, or personal injury:

• Read all safety information before you use the Product.

• Use the Product only as specified, or the protection

supplied by the Product can be compromised.

• Comply with local and national safety codes. Use personal

protective equipment (approved rubber gloves, face

protection, and flame-resistant clothes) to prevent shock

and arc blast injury where hazardous live conductors are

exposed.

• Do not use the Product around explosive gas, vapor, or in

damp or wet environments.

• Examine the case before you use the Product. Look for

cracks or missing plastic. Carefully look at the insulation

around the terminals.

Table 1. 80i-2010s AC/DC Current Clamp

Item Description Item Description

Tactile Barrier DJaws

Zero Adjust EBattery Cover

Fastener

ON/OFF FBattery Cover

• Use Product-approved measurement category (CAT),

voltage, and amperage rated accessories (probes, test

leads, and adapters) for all measurements.

• Do not use test leads if they are damaged. Examine the

test leads for damaged insulation and measure a known

voltage.

• Before each use, examine the Product. Look for cracks or

missing pieces of the clamp housing or output cable

insulation. Also look for loose or weakened components.

Carefully examine the insulation around the jaws.

• Hold the Product behind the tactile barrier. See  of

Table 1.

• Do not use the Product if it is damaged.

• Do not use the Product if it operates incorrectly.

• The battery door must be closed and locked before you

operate the Product.

• Remove all probes, test leads, and accessories before the

battery door is opened.

• Do not work alone.

• Do not exceed the Measurement Category (CAT) rating of

the lowest rated individual component of a Product,

probe, or accessory.

• Do not touch voltages >30 V ac rms, 42 V ac peak, or

60 V dc.

• Have an approved technician repair the Product.

Table 2 shows symbols that can be used on the Product or in this

document.

Table 2. Symbols

Symbol Definition

WWARNING - RISK OF DANGER.

XWARNING. HAZARDOUS VOLTAGE. Risk of electric

shock.

Consult user documentation.

TDouble Insulated

,Application around and removal from uninsulated

hazardous live conductors is permitted.

Battery

)Certified by CSA Group to North American safety

standards.

Operating Instructions

XW Warning

To prevent possible electrical shock, fire, or personal injury:

• When using the Clamp, ensure that your fingers are

behind the protective barrier as shown in Table 1.

• Do not use the Clamp if any part, including the lead and

connector(s), appears to be damaged or if a malfunction

of the instrument is suspected.

• Before using the clamp make sure there is no dust or any

small debris on the closing faces of the jaw.

• Close the jaws gently and avoid closing them with high-

impact. The force of the impact can affect the accuracy of

the measurement.

Turn on the Clamp

Push + for 2 seconds to turn on/off the clamp.

• Green LED indicates the Clamp is ON and the battery is ok.

• Orange LED indicates the battery is lower than 2.2 V.

• Red LED indicates the battery is lower than 2 V. Replace the

battery before doing a measurement.

PConforms to European Union directives.

Conforms to relevant Australian Safety and EMC

standards.

Conforms to relevant South Korean EMC Standards.

Measurement Category III is applicable to test and

measuring circuits connected to the distribution part of

the building’s low-voltage MAINS installation.

Measurement Category IV is applicable to test and

measuring circuits connected at the source of the

building’s low-voltage MAINS installation.

This product complies with the WEEE Directive marking

requirements. The affixed label indicates that you must

not discard this electrical/electronic product in domestic

household waste. Product Category: With reference to

the equipment types in the WEEE Directive Annex I, this

product is classed as category 9 "Monitoring and

Control Instrumentation" product. Do not dispose of this

product as unsorted municipal waste.

Table 2. Symbols (Continued)

Symbol Definition

Zero Adjustment

The output zero offset voltage of the Clamp may change due to thermal

shifts and other environmental conditions. To adjust the output voltage to

zero:

1. Make sure that the Clamp is away from the current carrying

conductor.

2. Push Zero Adjust and wait until the power LED (+) stops flashing.

Note

The Clamp cannot do the zero adjustment if the output

voltage is ±25 mV.

Current Measurement

To measure current:

1. Turn on the Clamp and check the LED status.

2. Connect the output lead/adapter to an oscilloscope, mulitmeter,

power analyzer, or other measuring equipment.

3. If necessary, adjust the Clamp output voltage to zero as described

in the section Zero Adjustment.

4. Clamp the jaw around the conductor and make sure there is good

contact between the closing faces of the jaw.

5. Take measurements as required. Positive output indicates that the

current flow is in the direction shown by the arrow on the clamp.

Maintenance

Before each use, inspect the Clamp. Look for cracks or missing portions of

the housing and output cable insulating cover and for loose or weakened

components.

Cleaning and Storage

Periodically wipe the case with a damp cloth and detergent. Do not use

abrasives or solvents. Do not immerse the Clamp in liquids.

Battery Replacement

XW Warning

To prevent possible electrical shock, fire, or personal injury:

• Replace the batteries when the low battery indicator

shows to prevent incorrect measurements.

• Always remove the Clamp from any live electric circuit,

and make sure leads are disconnected before removing

the battery cover.

• Never operate the Clamp without the battery cover

installed.

When the clamp approaches the minimum operating voltage, the red LED

indicates the battery is low.

To replace the battery (see Figure 1):

1. Disconnect the Clamp from any conductor.

2. Turn off the Clamp.

3. Disconnect the output leads from external equipment.

4. Locate the battery cover on the handle and unlock the fastener.

5. Remove the battery door and install the new batteries (IEC LR6).

6. Replace the battery cover, and lock the fastener.

Note

Replace the battery with the specified type only. Replacing

with the wrong battery type will invalidate the warranty.

Figure 1. Battery Installation

General Specifications

Dimensions..................................... 110 mm x 270 mm x 46 mm

Weight ............................................ 710 g

Output Cable .................................. 1.5 m Shielded Coaxial cable with

BNC male connector

Maximum Conductor Diameter....... 52.0 mm

Maximum Jaw Opening.................. 81.5 mm

Output to Zero ................................ Auto adjustment with zero button

Temperature

Operating .................................... -10 °C to 50 °C

Storage (battery removed) .......... -30 °C to +60 °C

Operating Humidity ..............................≤90 % RH (at 10 °C to 30 °C)

≤75 % RH (at 30 °C to 40 °C)

≤45 % RH (at 40 °C to 50 °C)

Altitude

Operating.................................. 2000 m

Storage..................................... 12 000 m

Demagnetize Clamp......................... Open and gently close the Clamp

jaws several times

Use of the clamp on non-insulated conductors is limited to 1000 V ac

rms or dc and frequencies below 1 kHz

Safety ............................................. IEC 61010-1, Pollution Degree 2

IEC 61010-2-032: CAT III 1000 V /

CAT IV 600 V

Ingress Protection .......................... IEC 60529, IP40

1 2

Electromagnetic Compatibility (EMC)

International.............................. IEC 61326-1: Portable

Electromagnetic Environment

IEC 61326-2-2, CISPR 11: Group 1,

Class A

Group 1: Equipment has intentionally generated and/or use

conductively coupled radio-frequency energy which is necessary for

the internal functioning of the equipment itself.

Class A: Equipment is suitable for use in all establishments other

than domestic and those directly connected to a low voltage power

supply network which supplies buildings used for domestic purposes.

There may be potential difficulties in ensuring electromagnetic

compatibility in other environments, due to conducted and radiated

disturbances.

Emissions that exceed the levels required by CISPR 11 can occur

when the equipment is connected to a test object.

Korea (KCC) ................ Class A Equipment (Industrial Broadcasting &

Communication Equipment)

Class A: Equipment meets requirements for industrial

electromagnetic wave equipment and the seller or user should take

notice of it. This equipment is intended for use in business

environments and not to be used in homes.

Electrical Specifications

All accuracies stated at 23 °C ±1 °C (73.4 °F ±1.8 °F)

Current Range ............................... 2000 A ac rms, ±2000 Adc

Output Sensitivity ........................... 1 mV/A

Accuracy......................................... ±0.8 % of reading ±0.2 % of range

Bandwidth to Meet

Accuracy Specification ................... DC to 400 Hz

Load impedance............................. >1 MΩ and <10 pF

Frequency Response

(small signal) .................................. DC to 20 kHz (-3dB)

Temperature Coefficient................. Add 0.1 x specified accuracy for each

degree C above 28 °C or below 18 °C

Working Voltage ............................. 1000 V ac rms or dc

Power Supply

Type ............................................ 2x AA alkaline battery, IEC LR6

Battery Life .................................. 150 hours

Low battery indicator ................... yes

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship

for one year from the date of purchase. This warranty does not cover

fuses, disposable batteries, or damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or handling.

Resellers are not authorized to extend any other warranty on Fluke’s

behalf. To obtain service during the warranty period, contact your nearest

Fluke authorized service center to obtain return authorization information,

then send the product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do not allow

the exclusion or limitation of an implied warranty or of incidental or

consequential damages, this limitation of liability may not apply to you.

11/99

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

Beijing Fluke

Rm101, 1/F.,Tong Heng Tower

No. 4 Hua Yuan Road Hai Dian

District, Beijing 100088, P.R.C.

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke PM6690 Manuel utilisateur

Fluke

Fluke i1000s Guide de référence

Fluke

Fluke 1730 Manuel d'utilisation et d'entretien

Fluke

Fluke 323 Manuel utilisateur

Fluke

Fluke 30 Instructions d'utilisation et d'installation

Fluke

Fluke 80i-410 Manuel utilisateur

Fluke

Fluke CableAnalyzer DSX-5000 Manuel utilisateur

Fluke

Fluke i100 Manuel utilisateur

Fluke

Fluke 525B Manuel utilisateur

Fluke

Fluke DSX-600 CableAnalyzer Manuel d'utilisation et d'entretien

Fluke

Fluke 435-II Manuel utilisateur

Fluke

Fluke a3002 FC Manuel utilisateur

Fluke

Fluke VIBGUARD IIoT Mode d’emploi

Fluke

Fluke BT21ANG Manuel utilisateur

Fluke

Fluke MultiFiber Pro Manuel utilisateur

Fluke

Fluke 741B Manuel utilisateur

Fluke

Fluke i430-Flexi-TF-II Manuel utilisateur

Fluke

Fluke C9970 Manuel utilisateur

Fluke

Fluke i3000s Flex Series Manuel utilisateur

Fluke

Fluke A3003 FC Manuel utilisateur

Fluke

Fluke 393 Manuel utilisateur

Fluke

Fluke 715 Manuel utilisateur

Fluke

Fluke etherscope II Manuel utilisateur

Fluke

Fluke 374 FC Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur