FLIR Extech 380926 Manuel utilisateur

User's Manual

2000A Auto Ranging

True RMS Clamp + DMM

MODEL 380926

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

INTRODUCTION

Congratulations on your purchase of Extech’s 380926 Clamp meter + Digital MultiMeter. This meter

can measure to 2000A through the clamp and also measure to 400mA through the test leads. With

Capacitance, Diode and Duty Cycle measurements, this meter provides the user with a full featured

multimeter combined with the high amperage current clamp. This meter is shipped fully tested and

calibrated and, with proper use, will provide years of reliable service.

SAFETY

Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates the user must refer to

the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous

voltages may be present

Double insulation

WARNING: This indicates that a potentially hazardous condition which, if not avoided, could result

in death or serious injury.

CAUTION: This indicates that a potentially hazardous condition which, if not avoided, could result

in injury or damage to the meter Reply to request.

Safety Precautions

1. WARNING: Improper use of this meter can cause damage, shock, injury or death. Read and

understand this user’s manual before operating the meter.

2. Make sure any covers or battery doors are properly closed and secured.

3. Always remove the test leads before replacing the battery or fuses.

4. Inspect the condition of the test leads and the meter itself for any damage before operating the

meter. Repair or replace any damage before use.

5. Do not exceed the maximum rated input limits.

6. Use great care when making measurements if the voltages are greater than 25VAC rms or

35VDC. These voltages are considered a shock hazard.

7. Always discharge capacitors and remove power from the device under test before performing

Capacitance, Diode, Resistance or Continuity tests.

8. Remove the battery from the meter if the meter is to be stored for long periods.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

METER DESCRIPTION

Front panel

1. Current Sense Jaws

2. Function switch

3. Keypad

4. LCD display

5. Input jacks

Note: The tilt stand and battery compartment door are

located on the rear of the meter.

Symbols

AC current or Voltage

DC current or Voltage

Continuity

HDisplay hold

REL Relative

AUTO Auto range

Diode

Display Backlight

Units

mV, V millivolt, volt (voltage)

Ω, kΩ, MΩ ohm, kilohm, megohm (resistance)

% percent (duty cycle)

μA, mA, A microamps, milliamps, amps (current)

Hz, kHz hertz, kilohertz (frequency)

nF, μF nanofarad, microfarad (capacitance)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

OPERATING INSTRUCTIONS

Current Measurements using the Clamp, DC/AC

WARNING: Make sure that the test leads are disconnected from the meter’s terminals before

making current measurements with the clamp jaw.

WARNING: For safety, use the rubber input terminal cover when measuring current using the

Clamp.

1. Set the Function switch to 2000A position.

2. Press the FUNC key to select AC or DC current

3. For DC current measurements, push & hold

the DCA ZERO button until the reading

indicates zero.

4. Press the trigger to open jaw. Fully enclose

the conductor to be measured (see

diagram).

5. The clamp meter will automatically select

the proper range (Auto Range). To select

the range manually, press the RANGE

button before pressing DCA ZERO button.

6. Read the measured value from the LCD

display.

NOTE: If the DCA zero button is used to zero the

meter, the clamp meter remains in the auto-range mode. If the REL button is used, the

clamp meter will be placed in the manual range mode.

Current Measurements using the Test Leads, DC/AC

1. Set the Function switch to the mA or µA position.

2. Press the FUNC key to select AC or DC.

3. Connect the black test lead to the COM terminal and the red test

lead to the mA µA input jack.

4. Break the circuit under test (put the meter in series with circuit

under test) refer to diagram.

5. Read the measured value from the LCD display.

NOTE: The maximum reading for direct input current is 240mA AC/DC.

INCORRECT

More than one

conductor in jaws

CORRECT

One conductor in jaws

µA and mA

Current

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

Voltage Measurements, DC/AC

1. Set the Function Switch to the Vposition.

2. Press the FUNC key to select AC or DC.

3. Insert the black test lead to the COM input jack

and the red test lead into the Vinput jack.

4. Connect the test leads in PARALLEL with the

circuit to be measured (see diagrams).

5. Read the measured value from the LCD display.

Resistance Measurements

CAUTION: Before taking any in-circuit resistance measurements remove

power from the circuit under test and discharge all capacitors.

1. Set the Function switch to the Ωposition.

2. Press the FUNC key until the ohms symbol appears on LCD.

3. Insert the black test lead to the COM input jack and the red test lead to

the Ωinput jack.

4. Connect test leads to the device under test (see diagram).

5. Read the measured value from the LCD display.

Continuity Test

1. Set the Function switch to the position.

2. Press the FUNC key until the "Ω" and " " symbols appear on the display.

3. Insert the black test lead to the COM input jack and the red test lead to the Ωinput jack.

4. Connect the test lead tips to the device to be measured (refer to diagram for resistance

measurements above).

5. Read the measured value from the LCD display.

6. If the resistance is < 10Ωapprox. an audible signal will be heard.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

Diode Test

1. Set the Function switch to the diode position.

2. Press the FUNC key until the symbol appears on the LCD.

3. Insert the black test lead to the COM input jack and the red test lead to the input jack.

4. Connect the test lead tips to the diode. A typical diode forward voltage drop will indicate 0.3

to 0.7V. The reverse drop will indicate "OL", indicating high impedance. Proper diode check

should include both forward and reverse tests.

Frequency Measurement

1. Set the Function switch to the Hz position.

2. Press the FUNC key until the "Hz" symbol appears on the LCD.

3. Insert the black test lead to the COM input jack and the red test lead to the

Hz input jack.

4. Connect the tips of the test leads to the device to be measured (see

diagram).

5. Read the frequency value in Hz on the LCD.

Duty Cycle Measurements

Follow the steps as for Frequency measurements with the following exception: Press the “Hz/%”

key until the “%” symbol appears on the display.

Capacitance Measurement

1. Set the Function switch to the position.

2. Press the FUNC key until the "nF" symbol appears on the LCD.

3. Insert the black test lead to the COM input jack and the red test lead to the

red input terminal.

4. Connect the tips of the test leads to the device to be measured (see

diagram).

5. Read the capacitance value on the display.

NOTE: When making very low capacitance measurements, use the REL function

to zero any stray capacitance.

RED REDBLACK BLACK

FORWARD TEST REVERSE TEST

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

Automatic / Manual Range Selections

The meter defaults to the autoranging mode when turned on. "AUTO" will appear in the display.

To select manual ranging, press the RANGE key. Momentary presses of the RANGE key will

step through the ranges. To return to the Auto Range mode, press and hold the RANGE key for 2

seconds.

Relative Reading Measurements

Press the REL key to enter the relative mode. "REL" will appear in the display. In the relative

mode, the meter stores the reading that was on the display at the time of the REL key is pressed

and displays the difference between the measured value and the stored value

Press the REL key to return to normal mode.

Data Hold / Backlight key

Press the HOLD key momentarily to freeze the present reading on the LCD."H" will appear in the

display. Press HOLD again to return to normal operation.

Backlight

Press and hold the Hold key for 2 seconds to activate the backlighting. The backlight will

automatically turn off to conserve energy after approx 12 seconds.

MAINTENANCE

Battery Replacement

When the low battery symbol appears on the LCD, replace the meter’s 9V battery.

1. Remove power to the meter and remove test leads from meter

2. Remove the Phillips head screw (back of meter) and open the battery compartment.

3. Remove and replace the 9V battery.

4. Replace the compartment cover and rear screw.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever

batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at

the end of its lifecycle

Fuse Replacement

NOTE: Fuse Rating: 500mA (5mm x 20mm diameter)

1. The meter is provided with one overload protect 500mA fuse for current measurements

(direct input NOT clamp measurements).

2. To replace the fuse, open the meter case by removing the battery cover and battery and then

the four screws holding the rear case.

3. The fuse is located on the Main PCB.

4. Replace fuse and secure meter case.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

SPECIFICATIONS

Function Range Resolution Accuracy Remarks

400.0A 0.1A ±(2.0% + 5d)AC/DC Current

(Clamp on) 2000A 1A ±(2.0% + 8d)

45Hz to 1KHz

4.000V 1mV

40.00V 10mV

400.0V 0.1V

AC Voltage

True RMS

1000V 1V

±(1.2% + 5d) 45Hz to 1KHz

Input Impedance:

10Mohms

400.0mV 0.1mV ±(0.5% + 2d)

4.000V 1mV

40.00V 10mV

400.0V 0.1V

DC Voltage

1000V 1V

±(1.0% + 2d)

Input Impedance:

10Mohms

400.0 Ω0.1Ω

4.000 kΩ1Ω

40.00 kΩ10Ω

400.0 kΩ100Ω

±(1.0% + 5d)

4.000 MΩ1kΩ±(2.0% + 2d)

Resistance

40.00 MΩ10kΩ±(3.5% + 5d)

400.0µA 0.1µA

4000µA 1µA

40.00mA 0.01mA

AC/DC Current

(Direct Input)

400.0mA 0.1mA

±(1.2% + 5d) 45Hz to 1KHz

5Hz 0.001Hz

50Hz 0.01Hz

500Hz 0.1Hz

5kHz 1Hz

50kHz 10Hz

Frequency

100kHz 100Hz

±(1% + 5d)

50nF 10pF

500nF 100pF

5µF 0.001µF

Capacitance

50µF 0.01µF

±(3% + 5d) Accuracy stated

after a relative "REL"

zero performed

Duty Cycle 1 to 99% 0.1% ±(1% + 5d)

Continuity Audible tone; <10 ohms approximately

Open circuit voltage; 0.5V approximately

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

380926 -EN-V7.1-3/12

Conductor Size 2.0”(50mm) maximum

Measurement parameters ACA, DCA, ACV, DCV, Resistance, Diode, Frequency,

Capacitance, Duty Cycle, Continuity

Current Sensor Hall Effect

Zero adjust Automatic except for DCA (Push-button)

Diode Test Test current of 0.6mA typical;

Open circuit voltage <1.6V DC typical.

Battery type 9V NEDA 1604

Range Selection Auto or manual

Display 0.6” (15mm) 5000 Count Backlit LCD

Overload Indication "OL"

Power Consumption 5mA approx.

Low Battery Indication Battery icon appears on LCD

Sampling rate 1 reading every 0.35 seconds approx.

Standards CE, IEC 1010-1 CAT III 1000V and CAT IV 600V

Operating Temperature/Humidity 32 to 122oF (0oC to 50oC) / <80%

Dimensions 10 x 2.9 x 1.5” (255 x 73 x 38mm)

Weight 0.85 lbs. (380g)

Maximum Rated Input Limits

Function Maximum Rated Input Limits

AC/DC Current 500mA AC/DC (fused)

AC Voltage 1000 VAC/DC

DC Voltage 1000 VAC/DC

Resistance 400 VAC/DC

Frequency 1000 VAC/DC

Capacitance 400 VAC/DC

Duty Cycle 1000 VAC/DC

Diode Test 400 VAC/DC

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Table des matières

Autres manuels FLIR Instrument de mesure

FLIR

FLIR CM42 Manuel utilisateur

FLIR

FLIR MR59 Manuel de l'opérateur

FLIR

FLIR Extech EX612 Manuel utilisateur

FLIR

FLIR Extech Instruments EX840 Manuel utilisateur

FLIR

FLIR CM55 Manuel utilisateur

FLIR

FLIR CM275 Manuel utilisateur

FLIR

FLIR VS80 KIT Manuel utilisateur

FLIR

FLIR CM42 Manuel utilisateur

FLIR

FLIR Extech Instruments RH520A Manuel utilisateur

FLIR

FLIR MR59 Manuel utilisateur

FLIR

FLIR identiFINDER R200 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR Extech Instruments 380193 Manuel utilisateur

FLIR

FLIR CM275 Manuel utilisateur

FLIR

FLIR identiFINDER R200 Manuel utilisateur

FLIR

FLIR TA50 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX2 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR DM284 Manuel utilisateur

FLIR

FLIR DM284 Manuel utilisateur

FLIR

FLIR CM83 Manuel utilisateur

FLIR

FLIR CM57-2 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX1 Dimensions

FLIR

FLIR MR160 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur