FeiYu Tech G360 Guide de démarrage rapide

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 1 -

G360 Gimbal Firmware Upgrade

Manual For Mac OSX

1.Please put the battery in before firmware upgrade.

2.The upgrade software and USB driver are compatible with the Mac OSX.

3.Please do the operations step by step strictly.

4.If you want to check current firmware version,please execute step 1-7.

1. Download the latest firmware ,update software and the USB driver from

our official website:www.feiyu-tech.com, Unzip them for further usage.

2.Double click on “ USB Driver for Mac.dmg ” to get “ Silicon Labs VCP

Driver.pkg”.Double click it to install the USB driver,and finish it step by step .

3.Please put the battery in, and refer the following connection diagram,

connect the USB cable with USB port of Mac and the gimbal.

The indicator on the handle of gimbal is solid red now.

Please keep the gimbal off until step 7.

Attention

Steps

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 2 -

4. Check the USB port by choosing “About This Mac”----”System Report”

--- “USB”, and check whether “CP2102 USB to UART bridge controller”

is in the hub list.

5. Double click on“Update for 3Axis”to run the update software.Please give

a permission in System Preferences-Security&Privacy because the program

isn’t downloaded from APP Store,and you have to run it with

your permission for the first time.

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 3 -

6.The software interface is shown as the following picture. Select

“cu.SLAB_USBtoUART” and the baud rate as 115200, then click on “OPEN

COM”.

7. Long press the function button, The connection between the gimbal and

Mac will be established automatically, The connection status and the

current version show up(For example, “LINK OK! VERSION 1. 03”) , Keep

holding the function button for 2~3 seconds after “LINK OK” showing up.

Release it, the indicator will alternately flashing blue and red. Which means

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 4 -

the power is ready and the connection is done.

(Tips: If you can’t see the indicator alternately flashing blue and red, please

long press the function button for 2 seconds again.)

8.Click on “OPEN FILE” button and choose right firmware for the gimbal，

then click“UPDATE START”to start updating. The block will be sent one by

one.

9.After all the blocks of the firmware are completely sent , please click on

“ok” to finish the upgrade. Close the software then unplug the USB cable.

Long press the function button of the gimbal to power off. All the upgrade

is done.

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 5 -

FAQ

NO.1 “Link ok ”didn’t show up when pressing the function button.

①Please check whether tightly plug in USB cable with USB port, and the

USB cable is right cable from our standard accessories.

② Please check whether keep the gimbal off until step7.

③ Please check whether choose the right USB port: cu.SLAB_USBtoUART

and baud rate as 115200.

④ Please check whether press the function button after clicking on “OPEN

COM“ button.

If you did all the things right, please replace a new USB cable and try again.

NO.2 When”LINK OK” and the version of current firmware showing up,

click on “UPDATE START”, but no luck, ”SEND FAIL” just show up to

remind me the update don’t work.

Guilin Feiyu Technology Incorporated Company

Guilin Feiyu Technology Incorporated Company www.feiyu-tech.com [email protected]

- 6 -

A: It happened because you didn’t hold the function button for enough

time, and the power didn ’ t start well. When the power is ready , the

indicator alternately flashes blue and red, if not, please keep holding the

function button for 2 seconds.

NO.3 After clicking on “UPDATE START”, “send block 10...” show up in

the interface , but ”SEND FAIL” happen during the update.

A: If ”SEND FAIL” shows up during the update, there may be something

wrong with the connection between control boards.

Please try to start update again, if the same issue happen, please kindly

send back to us for repair.

Check more details in tutorial video: https://youtu.be/yDHTLYQtnbc

–––– END ––––

Note: We reserve the right to change this manual at any time! And the

latest edition will be shown on our official website www.feiyu-tech.com.

Table des matières

Autres manuels FeiYu Tech Accessoires pour appareils photo

FeiYu Tech

FeiYu Tech SCORT-C F2C Manuel utilisateur

FeiYu Tech

FeiYu Tech MiNi 3D Manuel utilisateur

FeiYu Tech

FeiYu Tech Smart Stab Manuel utilisateur

FeiYu Tech

FeiYu Tech a1000 Manuel utilisateur

FeiYu Tech

FeiYu Tech Feiyu Pocket 2 Manuel utilisateur

FeiYu Tech

FeiYu Tech VIMBLE 2A Manuel utilisateur

FeiYu Tech

FeiYu Tech SPG Manuel utilisateur

FeiYu Tech

FeiYu Tech SCORP-C Manuel utilisateur

FeiYu Tech

FeiYu Tech FY-G4 GS Manuel utilisateur

FeiYu Tech

FeiYu Tech FY-G3 Ultra Manuel utilisateur

FeiYu Tech

FeiYu Tech AK2000S Guide d'installation

FeiYu Tech

FeiYu Tech G3 Steadycam Manuel utilisateur

FeiYu Tech

FeiYu Tech WG MINI Manuel utilisateur

FeiYu Tech

FeiYu Tech AK2000 Manuel utilisateur

FeiYu Tech

FeiYu Tech Cambox Manuel utilisateur

FeiYu Tech

FeiYu Tech AK4500 Manuel utilisateur

FeiYu Tech

FeiYu Tech VB 4SE Manuel utilisateur

FeiYu Tech

FeiYu Tech AK Series Manuel utilisateur

FeiYu Tech

FeiYu Tech SCORP Pro F4 Manuel utilisateur

FeiYu Tech

FeiYu Tech SPG 2 Manuel utilisateur

FeiYu Tech

FeiYu Tech FY-G4 GS Manuel

FeiYu Tech

FeiYu Tech G5 Manuel utilisateur

FeiYu Tech

FeiYu Tech MINI 3D Pro Manuel utilisateur

FeiYu Tech

FeiYu Tech Feiyu-WCP2 Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur