Fanvil i10 Manuel utilisateur
www.fanvil.com
JJ7J%
.JOJ4*1*OUFSDPN
2VJDL*OTUBMMBUJPO(VJEF
Package Contents
Mini Intercom
Quick Installation
Guide
Screw and tool
www.fanvil.com
JJ7J%
.JOJ4*1*OUFSDPN
2VJDL*OTUBMMBUJPO(VJEF
Connector
Mounting
Template
Physical specification
Device size 88 x 88 x 31 (mm)
i10 No camera, 1 button
With camera, 1 button
No camera, 2 button
i10V
i10D
1) Panel
Camera
Speaker
DSS key Call/Answer Unlock
Mountingdimensions Unit:MM
2) Interface description
Open the rear case of the device, there is a row of terminal blocks for connecting
the power supply, indoor switch. The connection is as follows：
ʒ
ʓʕʔ
Serial
number Description
Ethernet interface: standard
RJ45 interface, 10/100M
adaptive, it is recommended
to use five or five types of
network cable
Power interface: 12V/1A input
A set of short-circuit output
interfaces
A set of short-circuit input
interfaces
1
2
3
4
3) Installation Diagram
Cover Main body Back Shell Cover Main body Back Shell
1) Wall Mount: Attach the installation dimension drawing to the position to be installed,
use the electric drill to punch the hole in the 2 screw holes marked, and use the
hammer to drive the screw into the drilled hole.
Figure 3-1 Three Major Parts of i10&i10V Figure 3-2 Three Major Parts of i10D
Built-in: Attach the installation dimension drawing to the position to be installed, open a
groove of the same size according to the size, use the electric drill to punch the hole in
the 2 screw holes marked, and use the hammer to drive the screw into the drilled hole.
Fanvil Technology Co., Ltd
Email:[email protected]Tel:0755-2640-2199
Add: 4F, Block A, Building 1#, GaoXinQi Hi-Tech Park (Phase-II),
67th District, Bao'An, Shenzhen, China
Fax:0755-2640-2618
2) Remove the cover;
3) Use a screwdriver to remove the 4 screws on the main body to separate the main
body from the rear case;
4) Pass all the wires through the hole in the lower right corner of the bottom case. All
lines must be reserved for a length of 15~20CM;
5) Wall Mount: Align the bottom case with the position of the screw hole that was
previously punched on the wall, and screw in the two screws with a screwdriver to fix
the bottom case to the wall;
Built-in: Place the bottom case into the previously opened groove and screw in the two
screws with a screwdriver to secure the bottom case to the wall;
6) Test whether there is electricity by doing the following:
Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the
speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will
report the IP address by itself. If the work is normal, continue with the next steps.
7) Lock the 4 screws removed in step 3;
8) Cover the cover removed in step 2;
4) Searching Mini Intercom
There are two methods as shown below to search the device.
Methods 1:
Open the iDoorPhone Network Scanner, click the Refresh button to search the device
and find the IP address.
（Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )
Method 2:
Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the
speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will
report the IP address by itself.
172.18.70.55
In addition, device provides the device surface DSS key operation to switch IP
address acquisition mode:
In the standby mode, long-press the speed dial button for 3 seconds and the beep
will last for 5 seconds. Within 5 seconds, press the speed dial button three times
quickly to switch to the network mode.
If it is in the mode of DHCP and doesn't receive the IP address, switch it to the mode of
static IP (192.168.1.128), broadcast the IP address after the successful switch.
If it is in the mode of static IP address (192.168.1.128), switch it to the DHCP mode,
broadcast the IP address after the successful switch.
If it is in the mode of DHCP and obtain the IP address, the mode will not be switched
and directly broadcast the IP.
5) Mini Intercom Configuration
Step 1: Log in the WEB admin interface of the device
Input IP address (e.g.http://172.18.70.55) into address bar of PC’s web browser.
The default user name and password are both admin
Step 2: Add SIP account
Set SIP server address, port, user name, password and SIP user with assigned SIP
account parameters. Select <enable registration>, click <Apply> to take effect.
Step 3: Set DSS key
Set DSS key speed dial parameters, as shown below, click “Apply”to save this setting.
Type: Hot key.
Number 1: The DSS Key will dial to this Number 1.
Number 2: If number 1 is unavailable, it will be transferred to number 2.
Line: Working line.
Subtype: Speed Dial.
Step 4: Set the Intercom parameters
Step 5: Set the security function
1 set of short-circuit input and output settings, tamper alarm server settings.
Autres manuels pour i10
3
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Fanvil Système d'interphone
Fanvil
Fanvil i51W Manuel utilisateur
Fanvil
Fanvil i33V Manuel utilisateur
Fanvil
Fanvil i10 Guide d'installation et d'utilisation
Fanvil
Fanvil i56A Manuel utilisateur
Fanvil
Fanvil i12-02 Manuel utilisateur
Fanvil
Fanvil PA2 Manuel utilisateur
Fanvil
Fanvil I20-T Manuel utilisateur
Fanvil
Fanvil i31S Manuel utilisateur
Fanvil
Fanvil i20S Manuel utilisateur
Fanvil
Fanvil i55A Manuel utilisateur
Fanvil
Fanvil i16S-02P Manuel utilisateur
Fanvil
Fanvil i18 Manuel utilisateur
Fanvil
Fanvil i20S Manuel utilisateur
Fanvil
Fanvil i23S Manuel utilisateur
Fanvil
Fanvil i23 Manuel utilisateur
Fanvil
Fanvil i12 Manuel utilisateur
Fanvil
Fanvil i66 Manuel utilisateur
Fanvil
Fanvil V65 Manuel utilisateur
Fanvil
Fanvil i30 Manuel utilisateur
Fanvil
Fanvil i51W Manuel utilisateur
