Extron electronics MGP 641 Manuel utilisateur

MGP 641 • Setup Guide

The MGP 641 is a multi-window video signal processor that displays multiple video sources on a single screen in

picture-in-picture or picture-by-picture format. It features dedicated connectivity for each of the four windows, fully customizable

window layouts, HDCP 2.3 support, logo and background image support, logo keying, and ultra-high resolution support up to

2560x1600 and 4K at 60 Hz on both inputs and outputs. The MGP 641 can be controlled and congured using the front panel

controls, Simple Instruction Set™ (SIS™) commands, the internal web page, and the Videowall Conguration Software (VCS).

This guide provides instructions for an experienced installer to install and congure the MGP 641.

NOTES:

• For full installation, configuration, and operation details, see the MGP 641 Series User Guide, available at

www.extron.com.

• The VCS program is available at www.extron.com. For information on using VCS, see the VCS Help File, also available

on the Extron website.

Rear Panel Features and Connections

50 – 60 Hz

100-240V~ 1.5A MAX

MGP 641

BACKGROUND

INPUT

DEVICES

OUT

AUDIO OUT

REMOTE

LAN

RS-232

Tx Rx G

SIGLINK

Rx G

RESET

DTP

POWER

DTP2

OUTPUTS (DTP2/XTP/HDBT)

OVER TP

INPUTS

12 41A3

HDMI HDMI HDMI HDMI HDMI HDMI

USB 3.0

900mA

AAC power connector EDTP remote power LEDs IReset button and LED

BHDMI inputs FDTP/XTP/HDBT output (output 1B) JEthernet LAN connector

CHDMI live Background Input GOver TP IR pass through connector KAnalog Audio Out connector

D HDMI output (output 1A) HUSB Devices connectors LRemote RS-232 connector

Figure 1. Rear Panel

Installation Steps

1. Mount the MGP to a rack using the pre-installed side mounting brackets. The MGP 641 has a 1U high, full rack wide

enclosure.

Alternatively, attach the four provided rubber feet to the bottom of the MGP and place the unit in the desired location.

2. Connect HDMI (or DVI with an appropriate adapter) sources to the HDMI input connectors (inputs 1 through 4) (see figure1,

B).

3. If desired, connect a source to the HDMI live Background Input connector (C). The MGP 641 windows are displayed in front

of this unscaled background video source.

NOTE: You must set the output resolution to match that of the background source, or the background video is not

displayed. The refresh rates do not need to match.

4. Make the following output connections as needed:

zConnect an HDMI (or DVI with an appropriate adapter) display to the HDMI output 1A connector (D).

zConnect a DTP endpoint, XTP matrix switcher, or HDBaseT compatible receiver to the buffered DTP/XTP/HDBT output

connector 1B (F). For cable wiring and recommendations, see the MGP 641 User Guide.

NOTE: RS-232 data can be inserted via Ethernet (see the MGP 641 User Guide or the VCS Help File).

zTo pass infrared data, connect a control device to the 3-pole Over TP IR captive screw connector (see the MGP 641 User

Guide for information).

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

5. Connect a balanced or unbalanced analog audio output device (such as a DSP device or an amplifier) to the 5-pole captive

screw Audio Out connector (see figure1, Kon the previous page) for 2-Ch audio from the selected input. This connector is

configurable via VCS or SIS as two discrete mono outputs or as one stereo output (see “Audio Wiring” for details).

6. If the MGP 641 will be connected to a computer or to a host controller for remote control, connect an RS-232 cable from

the host to the Tx, Rx, and G pins (the remaining two pins are not used) of the 5-pole Remote RS-232 rear panel connector

(see figure1, L), or to the front panel USB mini-B Config port (see figure2, A). The default protocol for the RS-232 port is

9600 baud, 1 stop bit, no parity, and 8 data bits, with no flow control.

Alternatively, connect an RJ-45 network cable to the rear panel LAN port for remote conguration and control.

7. Connect power to the MGP by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz power

source into the AC power connector (see figure1, A).

8. Apply power to all other devices.

Audio Wiring

Wire the audio output connectors as

shown at right. Use the supplied tie wrap

to strap the audio cable to the extended

tail of the connector.

ATTENTION:

• For unbalanced outputs, do not connect wires to the “-” poles.

• Pour les sorties asymétriques, ne connectez pas de câbles aux pôles «-» .

NOTE: The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

Front Panel Controls

The MGP 641 front panel buttons, Adjust knobs, and the LCD menu provide navigation of general settings required to initially

control and congure the MGP. When you press a button or rotate a knob, the LCD panel displays the available settings.

MGP 641

MULTI-GRAPHIC PROCESSOR

CONFIG

WINDOW SELECT ADJUST

MUTE

FREEZE

PRESET

RECALL

/SAVE

ENTER

WINDOW

/IMAGE

SIZE

WINDOW

/IMAGE

POSITION

AUTO

IMAGE

WINDOW

/IMAGE

ZOOM

BB CC DD EE FF GG HH

AUSB Config port EPicture control buttons

BWindow and input selection buttons FLCD screen

CMute and Freeze buttons GMenu navigation buttons

DPreset Recall/Save and Enter buttons HHorizontal and vertical Adjust knobs

Figure 2. MGP 641 Front Panel

AUSB Config port — Connect a host device to this USB mini-B port for device configuration, control, file transfer, and

firmware upgrades.

BWindow selection buttons — Press these buttons to select windows (inputs) 1 through 4 for configuration. The selected

button lights orange.

CMute and Freeze buttons —

zMute — Press this button to mute the selected window. The button lights orange when the mute is enabled. To unmute,

press the lit Mute button again.

zFreeze — Press this button to freeze the selected window. The button lights orange when freeze is enabled. To unfreeze

the window, press the lit Freeze button again.

DPreset Recall/Save and Enter buttons — In combination, these buttons save the current settings to a window preset or

recall a stored preset (up to 128). Press Preset Recall/Save, then rotate the Adjust knobs to select a window preset to

save or recall. Press Enter to complete the action.

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Do not tin the wires

MGP 641 • Setup Guide (Continued)

EPicture control buttons — Press these buttons to adjust the size, position, and zoom, or to perform an auto-image

adjustment on the selected window.

zPress Window/Image Size, Window/Image Position, or Window/Image Zoom once to select the window (the button

lights orange) or twice to select the image within the window (the button lights green).

Use the horizontal ([) and vertical ({) Adjust knobs to adjust the settings shown on the left and right sides of the LCD

screen, respectively.

zPress Auto Image to perform an auto image adjustment on the selected input window. Press it again to confirm the

adjustment.

FLCD screen — Displays the configuration menus, messages, and your selections.

GMenu navigation buttons — Press Menu to step through the menus on the LCD screen. From each menu, press Next to

step through its submenus.

HHorizontal and vertical Adjust knobs — Turn these knobs to step through submenu options and preset slots, and to

adjust picture controls.

Setting Up the MGP 641 Using the Front Panel

After installing and connecting the MGP 641, use the front panel controls to congure

and adjust the unit for use. Press the Menu button to access the Main Menu (shown at

right). Then, repeatedly press the Menu button to cycle through the menus and access

the Input Conguration, Output Conguration, and Advanced Conguration menus

to perform steps 1 through 4.

1. Use the Input Configuration menu to configure inputs 1 through 4, including

EDID selection, aspect ratio selection, HDCP authorization, and image rotation

(available only for inputs 2 and 4) (some of these settings may require about

3 seconds to take effect after selection).

2. Use the Output Configuration menu to configure the outputs, including signal

type, resolution and rate, HDCP Note (encryption notification), TP and HDMI format,

and display rotation.

3. From the Advanced Configuration menu, Test Pattern submenu, use the crop

and grayscale test patterns to adjust the display settings.

4. Use the front panel menu system to set the IP address for your unit:

a. Press the Menu button repeatedly until the View Comm Settings menu name is

displayed on the LCD screen.

b. Press and hold the Next button until the screen displays Edit Comm Settings.

c. Press the Next button repeatedly until IP Address appears on the screen.

d. Rotate the Horizontal Adjust knob ([) to select a section of the address

(octet) to edit and the Vertical Adjust knob ({) to increase or decrease the

selected number.

e. Repeat step d for the remaining octets.

5. Use the picture control buttons to size and position each window as desired for

your application.

6. Save each window configuration to any of the 128 window preset slots for easy

recall of window settings.

Saving and Recalling Presets

To save the current conguration as a preset:

1. Press and hold the Preset Recall/Save button until the LCD screen displays

Window Preset/Save to #nnn (approximately 2 seconds). The button lights orange.

2. Rotate either Adjust knob to select the preset number or name to which you want

to save this configuration.

3. Press the Enter button. The button lights orange. Both the Preset Recall/Save

and the Enter buttons remain lit until the preset is saved, then turn off.

Power

OUTPUT

CONFIGURATION

30 sec.

IMAGE/LOGO

CONFIGURATION

30 sec.

Default

Cycle

2 sec.

ADVANCED

CONFIGURATION

EXIT MENU

PRESS NEXT

30 sec.

VIEW COMM

SETTINGS

30 sec.

INPUT

CONFIGURATION 30 sec.

30 sec.

Extron MGP 641

Vn.nn

WINDOW

CONFIGURATION

Hold 5 sec.

EDIT COMM

SETTINGS 30 sec.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

To recall a saved preset, press the Preset Recall/Save button and immediately release it. The button lights orange, and the

LCD window displays Window Preset/Recall #nnn. Rotate either Adjust knob to select a preset number, then press Enter. The

Enter button lights orange and remains lit until the window preset is recalled, then both buttons turn off.

SIS Commands

As an alternative to the front panel controls, you can issue SIS commands via RS-232, USB, or Ethernet from the computer to set

up the MGP 641 (see the MGP 641 User Guide at www.extron.com for a complete list of SIS commands).

Command ASCII (Telnet) Response Additional Description

Mute (blank) a window X!*B X!Vmt*1]Blank (mute) window X!.

Unmute a window X!*0B X!Vmt*0]Unmute window X!.

Save window preset 1*X1$,Spr1*X1$] Save current window settings as preset X1$.

Recall window preset 1*X1$.Rpr1*X1$] Recall window preset X1$.

Audio input switch X!$ InX!•]Select (switch) the audio from input X!.

Global audio mute X$Z AmtX$] Set mute state of all audio outputs to X$.

Discrete audio mute X@*X$Z AmtX@*X$] Set mute state of audio output X@ to X$.

View global mute status ZX$• X$•X$] View audio mute status:

HDMI, DTP, analog audio

View discrete audio mute X@*Z X$] View mute status X$ of audio output X@.

Set front panel lock mode X3%X ExeX3%] Set front panel lock mode to X3%.

Read front panel lock

mode

XX3%] View front panel lock mode X3%.

Set IP address EX10& CI }Ipi•X10&] Set unit IP address X10&.

Read IP address ECI } X10&] View the unit IP address (X10&).

Set subnet mask EX11# CS }Ips•X11#] Set unit subnet mask X11#.

Read subnet mask ECS } X11#] View the unit subnet mask (X11#).

Set gateway address EX10& CG }Ipg•X10&] Set IP address X10& for your gateway.

Read gateway address ECG } X10&] View the gateway IP address for your unit.

Reboot networking E2Boot}Boot2]Restart the network after IP setting or

DHCP changes.

KEY:

X! = Input (window) number 1- 4. 0= all windows (mute and freeze only)

X@ = Output number 1= HDMI output, 2= TP output, 3= Analog audio output, 99 = All outputs

X$ = Mute status 0= unmuted, 1 = muted

X1$ = Window preset number 1-128

X3% = Front panel lock (executive) mode 0= Off (front panel unlocked, default),

1= Complete front panel lockout

2= Only window preset recall, mute, freeze, and auto image are available.

X10& = IP or gateway address nnn.nnn.nnn.nnn. Leading zeros are optional in each octet.

X11# = Subnet mask nnn.nnn.nnn.nnn. Leading zeros are optional in each octet.

NOTE: IP and subnet commands require a 2BOOT command before any changes are applied (see the Reboot

Networking command, above).

68-2396-50

Rev. A 10 20

Autres manuels pour MGP 641

Autres manuels Extron electronics Convertisseur de média

Extron electronics

Extron electronics TLI Pro 201 Manuel utilisateur

Extron electronics

Extron electronics MediaPort 300 Manuel utilisateur

Extron electronics

Extron electronics IN1608 xi IPCP SA with LinkLicense Manuel utilisateur

Extron electronics

Extron electronics SENTOSAxi Manuel utilisateur

Extron electronics

Extron electronics SME 211 Manuel utilisateur

Extron electronics

Extron electronics HAE 100 Manuel utilisateur

Extron electronics

Extron electronics DVI to Analog RGB Video Converter DVI-RGB... Manuel utilisateur

Extron electronics

Extron electronics VN-Matrix 225 Series Manuel utilisateur

Extron electronics

Extron electronics QGE 100 Manuel utilisateur

Extron electronics

Extron electronics Digital Video Scalers DVS 204 Series Manuel utilisateur

Extron electronics

Extron electronics NAV 10E 401 D Manuel utilisateur

Extron electronics

Extron electronics VN-Matrix 200 Series Manuel utilisateur

Extron electronics

Extron electronics VSC 150 Manuel utilisateur

Extron electronics

Extron electronics NAV SD 511 Manuel utilisateur

Extron electronics

Extron electronics Sync Converter/Stabilizer SCS 300 Manuel utilisateur

Extron electronics

Extron electronics NAV SD 511 Manuel utilisateur

Extron electronics

Extron electronics BUC 202 Manuel utilisateur

Extron electronics

Extron electronics 3G-AE 100 Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-3G A Manuel utilisateur

Extron electronics

Extron electronics NAV E 401 D Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel utilisateur

Extron electronics

Extron electronics SDI to Analog Video Converter SDI-AVR 100 Manuel utilisateur

Extron electronics

Extron electronics DSC 301 HD Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur