Extron electronics CLK 100 Manuel utilisateur

User’s Guide

68-553-01 C

Printed in the USA

02 02

High Definition SDI to Component Video/RGB Converter

SDI to Video/RGB Converter

HDSDI-ACR 100

SDI-AVR 100

HDSDI-ACR 100 and SDI-AVR 100 • Installation 3HDSDI-ACR 100 and SDI-AVR 100 • Installation

Installation

(2) 4-40 x 1/8" Screws

Use 2 mounting holes on

opposite corners.

False front panel

uses 2 front holes.

HDSDI-ACR100

HDSDITOVIDEO/RGBCONVERTER

720

1080

FORMAT

Figure 2 — Rack mounting the SDI-AVR 100

b. Mount the SDI-AVR 100 on the rack shelf, using two 4-40 x

1/8 screws in opposite (diagonal) corners.

2. If desired, attach a false front panel or a second ½-rack-width

device to the other side of the shelf.

3. Attach the rack shelf to the rack using four 10-32 x ¾” bolts and

four #10 beveled dress washers.

Rear Panel Cabling

Figure 3 shows the HDSDI-ACR 100 connections and DIP switches.

Figure 4 shows the SDI-AVR 100.

SOG OFF/ON

RGB/COMPONENT

BI/TRI-LEVEL

SPARE

100-240V 0.1A

50/60 Hz

HDSDI INPUT

OUTPUTS

IN OUT

R/R-Y G/Y B/B-Y

HVS

216 7

Figure 3 — HDSDI-ACR 100 rear panel

Input In connector — Connect an HDSDI (HDSDI-ACR 100) or

SDI (SDI-AVR 100) input to this BNC connector.

Input Out connector — Connect an HDSDI (HDSDI-ACR 100) or

SDI (SDI-AVR 100) device to this BNC connector. The converter

outputs a reclocked SDI or HDSDI loop-though on this BNC.

Overview

The Extron HDSDI-ACR 100 converts a high definition (HD) serial

digital interface (SDI) input (SMPTE-292M) to either analog component

or RGB video. The converter supports the 720p, 1080i, and 1080p HDTV

rates. The 1080p rate is limited to a maximum 30 Hz refresh rate and

includes 1080p segmented frame 23.94/24. DIP switches select between

RGB and component video, and, for component video output, between

bi-level and tri-level sync, and sync on the Y output or on all outputs.

The Extron SDI-AVR 100 converts an SDI (4:2:2) video input at the

270 Mbs rate to analog video. When an SDI input is applied, the

converter produces simultaneous composite and S-video outputs, and

either component (Y, R-Y, and B-Y) or RGB video. A DIP switch selects

between a component or RGB video output. The SDI-AVR 100 accepts

NTSC, PAL, and Betacam (Beta 50/60), autodetects the format, and

deserializes the input. The converter can output NTSC or PAL color

bars, which are DIP switch selectable.

SOG

RGB/YUV

SETUP

BETA

COLORBARS

NTSC/PAL

100-240V50/60Hz0.2A

SDIINPUTOUTPUTS

OUT

COMPOSITE

OUTPUTS-VIDEO

OUTPUT

R/R-YG/YB/B-Y

HVS

OFF

SDI-AVR 100

SOGOFF/ON

RGB/COMPONENT

BI/TRI-LEVEL

SPARE

100-240V0.1A

HDSDIINPUT

OUTPUTS

IN OUT

R/R-YG/YB/B-Y

HVS

Betacam Recorder

Camera

Monitor

Large Screen

Rear Projector

HDSDI-ACR 100

HDTV Tape Deck

HDTV Camera Projector

Figure 1 — Typical HDSDI-ACR 100 and SDI-AVR 100

applications

The input signal is equalized for distances of 330 feet (100 meters)

(HDSDI-ACR 100) or 1000 feet (305 meters) (SDI-AVR 100) on high

quality cable such as Extron SHR cable. A reclocked loop-through

allows the HDSDI/SDI input to be sent to other equipment.

The user must select between an RGB or component video output using

a DIP switch. The converters output separate H and V sync signals and

composite sync simultaneously. Selecting the sync-on-green output

requires changing a DIP switch position.

The converters have internal switching power supplies.

Installation

1. For optional rack mounting, mount the converter on one side of a

19" 1U Universal Rack Shelf (Extron part #60-190-01) (figure 2).

a. If feet were previously installed on the bottom of the case,

remove them.

RGB/Component (HDSDI-ACR 100) or RGB/YUV (SDI-

AVR 100) switch — Set this switch to the Off position to

output RGB video. Set the switch on for component video.

Bi/tri-level switch (HDSDI-ACR 100 only) — Set this

switch to the On position to output tri-level sync on the

component video output. Set the switch off for bi-level

sync.

HDSDI-ACR 100 switch configuration

Output video format SOG

RGB/

Component Bi/tri-level

RGBHV/RGBS Off Off Either

RGsB On Off Either

Y, R-Y, B-Y w/ bi-level on Y Either On Off

Y, R-Y, B-Y w/ tri-level on Y Either On On

SDI-AVR 100 switch configuration

Output video format SOG RGB/YUV

RGBHV/RGBS Off Off

RGsB On

Either

Off

Y, R-Y, B-Y On

Set Up switch (SDI-AVR 100 only) — Set this switch to the On position

to output an NTSC signal that is on the 7.5 IRE pedestal. Set the

switch off to return the signal to the normal level.

Beta switch (SDI-AVR 100 only) — Set this switch to the On position to

set the color level of the YUV output to the Betacam level. Set the

switch off to restore the YUV output to the normal level. If a

Betacam signal is input, the switch should be set to On to output

the Betacam format. Otherwise, the output will be NTSC or PAL.

Color Bars switch (SDI-AVR 100 only) — Set this switch to the On

position to output NTSC or PAL color bars. Set the switch off for

the converted video input.

NTSC/PAL switch (SDI-AVR 100 only) — Used in conjunction with

the Color Bars switch only, set this switch to the On position to

output PAL color bars. Set the switch off for NTSC color bars.

Front Panel Indicators

All indicators are on the front panel. Figure 5 and figure 6 show

HDSDI-ACR 100 and SDI-AVR 100 indicators.

Power LED — The Power LED indicates that power is on.

720PLED (HDSDI-ACR 100 only) — The 720P LED indicates that

the converter is outputting the HDTV 720P video format.

SOG

RGB/YUV

SET UP

BETA

COLOR BARS

NTSC/PAL

100-240V 50/60 Hz 0.2A

SDI INPUT OUTPUTS

OUT

COMPOSITE

OUTPUT S-VIDEO

OUTPUT

R/R-Y G/Y B/B-Y

HVS

OFF

21 36 47

Figure 4 — SDI-AVR 100 rear panel

Composite Output connector (SDI-AVR 100 only) — Connect a

composite video display device to this BNC connector. This

output is available whenever an active SDI signal is applied to the

SDI input connector, 1.

S-video Output connector (SDI-AVR 100 only) — Connect an

S-video device to this 4-pin mini DIN connector. This output is

available whenever an active SDI signal is applied to the SDI

input connector, 1.

RGB/component video output connectors

Ensure that the rear panel DIP switches are in the correct

configuration (see Rear Panel Controls).

RGBHV video connection —

Connect to five BNC connectors

as shown.

RGBS video connection —

Connect to four BNC connectors

as shown.

RGsB and component video

connection — Connect to three

BNC connectors as shown.

AC power connector — Plug a

standard IEC power cord into

this connector to connect the

converter to a 100 to 240VAC, 50

Hz or 60 Hz power source.

Rear Panel Controls

DIP switches

SOG switch — Set this switch to the On position to output sync-

on-green for RGB video (RGsB). Set the switch off for

RGBHV or RGBS video.

R/R-Y G/Y B/B-Y

HVS

R/R-Y G/Y B/B-Y

HVS

R/R-Y

RGBHV

Video

RGBS

Video

RGsB or

Component

Video

G/Y B/B-Y

HVS

HDSDI-ACR 100 and SDI-AVR 100 • Installation and Operation 5HDSDI-ACR 100 and SDI-AVR 100 • Installation

Installation

SOG

RGB/YUV

SET UP

BETA

COLOR BARS

NTSC/PAL

OFF

SOG OFF/ON

RGB/COMPONENT

BI/TRI-LEVEL

SPARE

OFF

The equalization applied to the SDI-AVR 100’s input signal is

sufficient for an input coaxial cable length of at least 1000 feet (305

meters) of Extron SHR cable or Belden 8281 cable.

The equalization applied to the HDSDI-ACR 100’s input signal is

sufficient for an input coaxial cable length of at least 330 feet (100

meters) of Extron SHR cable or Belden 8281 cable.

Minimum/maximum levels ...... 0.5V to 1.0V p-p with no offset

Impedance .................................... 75 ohms

Return loss .................................... >-15dB @ 0 MHz to 270 MHz

Maximum DC offset .................... ±0.5V

Video processing

Encoder ......................................... 10 bit digital

Frequency response ..................... Luminance ................ 0 to 5.75 MHz, ±0.5dB

Chroma .................... 0 to 2.75 MHz, ±0.5dB

S/N ................................................ >70dB

RGB matrix error ......................... <1%

Video signal characteristics — for color bar output on the

SDI-AVR 100 only

Dot clock ....................................... 27 MHz

Pixel clock accuracy ..................... 30 ppm

Video output

Number/signal type

SDI-AVR 100 .................... 1 composite video and 1 S-video, and

1 analog RGBHV/RGBS/RGsB or component

video (Y, R-Y, B-Y) (switch selectable)

HDSDI-ACR 100 .............. 1 analog RGBHV/RGBS/RGsB or component

video (Y, R-Y, B-Y) (switch selectable)

Connectors

SDI-AVR 100 .................... 1 female BNC (composite video)

1 female 4-pin mini DIN (S-video)

6 female BNC (RGB, component video, or S-video)

HDSDI-ACR 100 .............. 6 female BNC

Levels ............................................. Composite video ...... 1V p-p (nominal)

S-video .................... 1V p-p/luma, 0.3V p-p/

chroma (nominal)

RGB .................... 0.7V (nominal)

Component video .... Y = 1V p-p; R-Y, B-Y = 1V

p-p (nominal)

Levels depend on the format selected (NTSC, PAL, Betacam).

HDSDI-ACR 100

HDSDITOVIDEO/RGB CONVERTER

720

1080

FORMAT

1 2 3 4

Figure 5 — HDSDI-ACR 100 front panel

SDI-AVR 100

SDITOVIDEO/RGB CONVERTER

LOCK

1 5

Figure 6 — SDI-AVR 100 front panel

1080ILED (HDSDI-ACR 100 only) — The 1080I LED indicates

that the converter is outputting the HDTV 1080I video format.

1080PLED (HDSDI-ACR 100 only) — The 1080P LED indicates

that the converter is outputting the HDTV 1080P video format.

Lock LED (SDI-AVR 100 only) — The Lock LED indicates that

the converter is locked to the 270 Mbs input signal.

Specifications

Video

Differential phase error .............. SDI-AVR 100 ............ <1º

Differential gain error ................. SDI-AVR 100 ............ <1%

Video input and loop-through

Number/signal type

SDI-AVR 100 .................... 1 SDI (4:2:2, SMPTE 259M-C)

HDSDI-ACR 100 .............. 1 HDSDI (SMPTE 292M)

Connectors

SDI-AVR 100 .................... 1 female BNC (SDI input)

1 female BNC (SDI reclocked loop-through)

HDSDI-ACR 100 .............. 1 female BNC (HDSDI input)

1 female BNC (HDSDI reclocked loop-through)

HDSDI-ACR 100 and SDI-AVR 100 • Specifications 7HDSDI-ACR 100 and SDI-AVR 100 • Specifications

Indicators and Specifications

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

Impedance .................................... 75 ohms

Return loss .................................... -30dB @ 5 MHz

Sync

Output type .................................. RGBHV, RGBS, RGsB

Standards (SDI-AVR 100 only) .. NTSC 3.58, PAL 4.43, Betacam

Output impedance....................... 75 ohms

Max. rise/fall time ....................... 200 nS

Polarity .......................................... SDI-AVR 100 ............ negative

HDSDI-ACR 100 ...... bi-level or tri-level sync

(switch selectable) on luma

(Y) leg

General

Power ............................................. 100VAC to 240VAC, 50/60 Hz, internal, auto-

switchable

SDI AVR 100 ..................... 6 watts

HDSDI AVR 100 .............. 10 watts

Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / 10% to

90%, non-condensing

Operating +32° to +122°F (0° to +50°C) / 10% to

90%, non-condensing

Rack mount................................... Yes, with optional rack shelf, part #60-190-01

Enclosure type .............................. Metal

Enclosure dimensions ................. 1.75" H x 8.75" W x 8.0" D

(1 rack unit high, half-rack unit wide)

4.5 cm H x 22.2 cm W x 20.3 cm D

(Depth excludes connectors.)

Shipping weight .......................... 4 lbs (1.8 kg)

Product weight

SDI-AVR 100 .................... 1.8 lbs (0.8 kg)

HDSDI-ACR 100 .............. 1.9 lbs (0.9 kg)

Vibration ....................................... ISTA/NSTA 1A in carton (International Safe

Transit Association)

Listings .......................................... UL, CUL

Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES

MTBF ............................................. 30,000 hours

Warranty ....................................... 3 years parts and labor

Autres manuels pour CLK 100

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Convertisseur de média

Extron electronics

Extron electronics DAC 102 Manuel utilisateur

Extron electronics

Extron electronics IN1606 Manuel utilisateur

Extron electronics

Extron electronics Balanced and Unbalanced Audio Converter BUC... Manuel utilisateur

Extron electronics

Extron electronics DVS 406 Manuel utilisateur

Extron electronics

Extron electronics Quantum Ultra Manuel utilisateur

Extron electronics

Extron electronics SMD 101 Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics HDP 101 4K Manuel utilisateur

Extron electronics

Extron electronics DVS 510 Manuel utilisateur

Extron electronics

Extron electronics PIP 422 Manuel utilisateur

Extron electronics

Extron electronics DDS 100 Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel

Extron electronics

Extron electronics CVC 100 Manuel utilisateur

Extron electronics

Extron electronics CVC 200 Manuel utilisateur

Extron electronics

Extron electronics SME 100 Manuel utilisateur

Extron electronics

Extron electronics Emotia Xtreme MX Manuel utilisateur

Extron electronics

Extron electronics DVS 150 Manuel utilisateur

Extron electronics

Extron electronics DSC 301 HD Manuel utilisateur

Extron electronics

Extron electronics Inertia Manuel utilisateur

Extron electronics

Extron electronics CVC 300 Manuel utilisateur

Extron electronics

Extron electronics Four Input Video and RGB Scaler DVS 304 Manuel utilisateur

Extron electronics

Extron electronics Two InpuT VIdeo Scaler IN1502 Manuel utilisateur

Extron electronics

Extron electronics NAV E 511 Manuel utilisateur

Extron electronics

Extron electronics CD 400 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur