Extron electronics DVC 501 SD Manuel utilisateur

Product Category

DVC 501 SD • Setup Guide

The Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to DVI-D and

analog RGB or component video. It is compliant with SMPTE 259M, 292M, 424M, and ITU digital video standards. The RGB

output can be set for RGBHV, RGBS, and RGsB. Bi-level or tri-level sync can be selected when the unit is set for component

video output. The DVC 501 SD features extraction of embedded AES3 audio, RS-232 and USB serial control, and a buffered

loop-through that delivers reshaped and restored multi-rate SDI signals.

NOTE: For full installation, conﬁguration, and operation details, see the DVC 501 SD User Guide, available at

www.extron.com.

Rear Panel Features and Connections

100-240V ~ 0.3A MAX

50/60 Hz

3G / HD / SD-SDI

BUFFERED

INPUT

LOOP-THROUGH RGB/R-Y,Y,B-Y

OUTPUT

DVI-D

RS-232

N/A Tx Rx

AUDIO

12456

aAC power connector dDVI-D output connector fAudio output connector

b3G/HD/SD-SDI input connector eRGB/YUV output connector gRS-232 connector

cBuffered Loop-through connector

Installation Steps

1. Disconnect power from all equipment.

2. (Optional) Mount the unit to a rack or furniture.

3. Connect the video input. Connect an SD-SDI, HD-SDI, or 3G-SDI source to the 3G/HD/SD-SDI port of the BNC input

connector (bin the rear panel illustration above).

4. (Optional) Connect a monitor or recording device. Attach a monitor or video recording device to the Buffered

Loop-through BNC connector (c).

5. Connect the video output. Connect a display or other output device to the DVD-D digital video connector (d) or to

the RGB/R-Y,Y,B-Y analog RGB (RGBHV, RGBS, and RGsB) or YUV component video connector (e).

6. Connect a control device. Connect a host device, such as a computer or touchpanel control system to one or both of

the following DVC ports to conﬁgure and control the DVC via Simple Instruction Set (SIS™) commands.

zRS-232 port (rear panel) — Connect a host device to the Tx, Rx, and _(ground) pins of this 5-pole captive screw

connector (g). The ﬁrst and second pins of this connector are not used. The default protocol for this port is

9600 baud, 1 stop bit, no parity, 8 data bits, and no ﬂow control.

zCong port (front panel) — Connect a USB cable (USB A to USB mini B) between a USB port on your computer

and this port (aon the front panel illustration on the next page).

7. Connect the audio output. Connect an ampliﬁer or other audio output device to the 5-pole captive screw audio

connector (fon the rear panel illustration), as shown below.

Do not tin the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

Sleeves

CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect them to negative (–)

contacts.

8. Connect power to the DVC 501 SD by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz

power source into the power receptacle (a).

68-1518-50 Rev. C

09 11

Front Panel Features

Extron

DVC 501 SD

DIGITAL VIDEO CONVERTER

ADJUST

CONFIG

1235

aUSB Conﬁg port bLCD screen cMenu button dNext button eAdjust knobs

Conguring the DVC 501 SD Using the Front Panel

Menu selections are displayed on the LCD screen. To use any menu, press the Menu button repeatedly until the desired

menu is displayed (see the menu ﬂow diagram below). Press the Next button repeatedly until the desired submenu appears.

Rotate an Adjust knob to select an item from a submenu. To return to the main menu at any time, press the Menu button.

After 30 seconds of inactivity, the screen displays the default cycle.

1. From the Output Conﬁg submenus, use the Adjust knobs to select the output signal

type and the sync polarity to match the requirements of the display device.

2. From the Advanced Conﬁg menu, Test Pattern submenu, select the Crop, Crosshatch,

Colorbars, and Grayscale test patterns to conﬁrm that the settings of the display device

are correct.

NOTE: Test pattern timings are based on the incoming SDI signals and are not

displayed if an active signal is not present.

3. Use the Audio Conﬁg submenus to conﬁgure the audio as desired.

Supported Input Resolutions

Supported

Resolutions 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

720p X X X X X X

1080i X X X

1080p X X X X X X X X

NTSC X

PAL X

NOTE: The output resolution always matches the input resolution.

Simple Instruction Set (SIS) Commands

When setting up the DVC 501 SD, you can issue SIS commands from your computer via RS-232 or USB as an alternative to

the front panel controls. See the DVC 501 SD Series User Guide for a complete list of available SIS commands.

Command ASCII command

(Host to Converter)

Response

(Converter to Host) Additional Description

Mute video 1B Vmt1]Mute the video output.

Unmute video 0B Vmt0 ]Display the video output.

Mute audio 1Z Amt1 ]Mute the audio output.

Unmute audio 0Z Amt0 ]Unmute the audio output.

Enable lock (executive) mode 1X Exe1]Lock all front panel functions.

Disable lock mode 0X Exe0 ]Enable all front panel functions.

AUDIO

CONFIG

30 sec.

Default

Cycle

EXIT MENU

PRESS NEXT

OUTPUT

CONFIG 30 sec.

30 sec.

ADVANCED

CONFIG

30 sec.

Autres manuels pour DVC 501 SD

Table des matières

Autres manuels Extron electronics Convertisseur de média

Extron electronics

Extron electronics VSC 900 Manuel utilisateur

Extron electronics

Extron electronics Two InpuT VIdeo Scaler IN1502 Manuel utilisateur

Extron electronics

Extron electronics NAV E 501 Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel utilisateur

Extron electronics

Extron electronics DVC 501 SD Manuel utilisateur

Extron electronics

Extron electronics DSC HD-3G A Manuel utilisateur

Extron electronics

Extron electronics Inertia Manuel utilisateur

Extron electronics

Extron electronics DSC 3G-HD A Manuel utilisateur

Extron electronics

Extron electronics CD 400 Manuel utilisateur

Extron electronics

Extron electronics HAE 100 4K Plus Manuel utilisateur

Extron electronics

Extron electronics VSC 50 Manuel utilisateur

Extron electronics

Extron electronics DSC 301 HD Manuel utilisateur

Extron electronics

Extron electronics Digital Video Scalers DVS 204 Series Manuel utilisateur

Extron electronics

Extron electronics VSC 900 Manuel utilisateur

Extron electronics

Extron electronics NAV E 511 Manuel utilisateur

Extron electronics

Extron electronics HAI 100 4K Manuel utilisateur

Extron electronics

Extron electronics MGP 641 Manuel utilisateur

Extron electronics

Extron electronics DDS 402 Manuel utilisateur

Extron electronics

Extron electronics DVS 150 Manuel utilisateur

Extron electronics

Extron electronics SMD 101 Manuel utilisateur

Extron electronics

Extron electronics DSC 401 Manuel utilisateur

Extron electronics

Extron electronics RGB to DVI Scaler RGB-DVI 300 Manuel utilisateur

Extron electronics

Extron electronics Quantum Ultra Series Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur