Extron electronics RCP 2000 Manuel utilisateur

User's Guide

68-575-02 Rev. A

Printed in the USA

10 03

The RCP 2000 will work with an ISS 108 or ISS 408 that has firmware version 1.01 or later.

Check the firmware installed in your ISS switcher. If the installed firmware is version is 1.0 or

earlier, install the firmware chips that are attached to this sheet.

Check the ISS’s Firmware level

Apply power to the ISS. During the power up process, the switcher displays the model name,

part number, and the firmware version in its LCD display (figure 1).

sec.

Extron Electronics

ISS 408

Integration

Seamless Switcher

Extron Electronics

ISS 408

60-423-01

Version

Version 1.00 or earlier,

you must replace the

firmware.

Version 1.01 or later,

you do not need to

replace the firmware.

Program #1 RGB

0.00 kHz 0.00Hz

Preview #3 S-Video

0.00 kHz 0.00Hz

Output Rate

1280 x 1024 @ 60

Power

Default Display Cycle

Figure 1 — Identifying the firmware version

Replace the ISS’s Firmware

1. Disconnect the AC power cord from the ISS to remove power from the unit.

To prevent electric shock, always unplug the ISS from the AC power source before

opening the enclosure.

CAUTION

Changes to firmware must be performed by authorized service personnel only.

2. If the ISS is installed in a rack, disconnect all signal and control cables and remove the ISS

from the rack.

3. Remove the 16 screws, 8 on the top and 4 on each side of the ISS cover (figure 2 on the

opposite side of this guide).

4. Remove the top two front panel screws.

5. Lift the top cover straight up approximately five inches until you can access the fan power

cords.

CAUTION

Do not touch any switches or other electronic components inside the ISS. Doing so

could damage the switcher. Electrostatic discharge (ESD) can damage IC chips even

though you cannot feel it. You must be electrically grounded before proceeding with

firmware replacement. A grounding wrist strap is recommended.

6. Disconnect the two fan power cords from connectors J8 and J13 on the main board.

7. Lift the top cover out of the way.

8. Locate firmware chip U6 on the front panel circuit board and chips U98, U99, U100, and

U101 on the main circuit board (figure 2).

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

9. After you are electrically grounded, use a DIP chip puller to grasp the IC

chips and pull them out of the socket.

10. The table in figure 2 identifies the socket into which each firmware chip

is to be installed.

Ensure the correct chip is installed in each socket. The wrong chip will

not work and may damage the ISS.

The U98 and U100 chips are identical and can be installed in either

location.

The U99 and U101 chips are identical and can be installed in either location.

12345678

100

240

50/60Hz

1.2AMAX.

H/HV

INPUTS

H/HV

Remove (16)

screws.

Remove top two

front panel screws.

Lift cover straight up.

Extron

ISS 408

Switcher

J8J13

Connect to

J8 and J13

U100

U101

U98

U99

Chip part #

19-1222-01

19-1218-02

19-1218-01

Location

U98 or U100

U99 or U101

Figure 2 — Opening the switcher and firmware locations

11. Align the notches on one end of each chip with the notches in the socket in the same

orientation as the old chips. Gently, but firmly, press the chips into place in the socket.

12. Reconnect the two fan power cords to connectors J8 and J13 on the main board. It does not

matter which fan is connected to which connector.

13. Replace the top cover on the ISS.

14. Fasten it with the screws that were removed in step 3and step 4.

15. Rack mount the switcher if desired and reconnect all cables.

The new firmware has several new features and revised LCD displays. Obtain the latest

ISS 108 and ISS 408 manual from the Extron Web site, www.extron.com.

Align

Notches

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]

Autres manuels pour RCP 2000

Autres manuels Extron electronics Panneau de contrôle

Extron electronics

Extron electronics MKP 2000 Manuel utilisateur

Extron electronics

Extron electronics ACP 105 D Manuel utilisateur

Extron electronics

Extron electronics IP Link Pro NBP 50 Manuel utilisateur

Extron electronics

Extron electronics ACP VC1 D Manuel utilisateur

Extron electronics

Extron electronics SCP 150L Manuel utilisateur

Extron electronics

Extron electronics RCP 101 EU Manuel utilisateur

Extron electronics

Extron electronics MCP 1000 Manuel utilisateur

Extron electronics

Extron electronics SCP 200 Manuel utilisateur

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manuel utilisateur

Extron electronics

Extron electronics SCP 250 Manuel utilisateur

Extron electronics

Extron electronics ACP VCI EU/MK Manuel utilisateur

Extron electronics

Extron electronics NBP 100 Manuel utilisateur

Extron electronics

Extron electronics RCP 2000 Manuel utilisateur

Extron electronics

Extron electronics RCP 101 D Manuel utilisateur

Extron electronics

Extron electronics Control Panel CTL208CM Manuel utilisateur

Extron electronics

Extron electronics ACP 100 Manuel utilisateur

Extron electronics

Extron electronics ACP 105 EU/MK Manuel utilisateur

Extron electronics

Extron electronics IPCP Pro Series Manuel utilisateur

Extron electronics

Extron electronics MLC Plus 84 EU Manuel utilisateur

Extron electronics

Extron electronics MKP 2000 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro x25M Series Manuel utilisateur

Extron electronics

Extron electronics SCP 104 Series Manuel utilisateur

Extron electronics

Extron electronics MKP 3000 Manuel utilisateur

Extron electronics

Extron electronics Decorator-Style Series Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques