Extron electronics ACP 100 Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

ACP 100 • Setup Guide

The Extron ACP 100 Audio Control Panel is a fully congurable control interface for use with the Extron DMP 128 Plus Digital

Matrix Processor.

Each ACP 100 includes two ACP ports, which support both power and communication between the DMP 128 Plus and the

ACP100. Up to four ACP panels can be daisy-chained together for more demanding control needs.

Front Panel Features

Extron

MIC

SOURCE

PROGRAM

VOLUME

MUTE

SOURCE

MIC PROGRAM

SOURCE

MUTE

SOURCE

RESET

ACP 100 Front Panel with Plastic

Faceplate

ACP 100 Front Panel without

PlasticFaceplate

EEEE

CCCC

BBB

AAA

DDDF

FFF

Figure 1. ACP 100 Front Panel

Rear Panel Features

PWR LOAD = 0.5W

123456

BUS ID

123456

ACP

S+S

+V G

S+S

ACP 100 Rear Panel

CCCC

DDD

BBB

AAA

Figure 2. ACP 100 Rear Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP 100 product page at www.extron.com for more information about the ACP 100).

APlastic Faceplate

BFunction Buttons 1 and 2

CFunction Buttons 3-6

DVolume LEDs and Knob

EMounting Holes (4)

FReset Button

ABus ID DIP Switches

BACP Ports (2)

CACP Status LED

DMaximum Power Load Rating

ACP 100 • Setup Guide (Continued)

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the DMP 128 Plus and

congure the connected ACP products (see the DMP 128 Plus User Guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 100 installation.

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 100 into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 100 dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 100 will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access

hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 100 dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualifié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 100 must

be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the

ACP100.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, you may need to consider factors affecting accessibility of the button panel such

as height from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see

sections 307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external

wall boxes (EWBs), and surface or tabletop mounting boxes for use with the ACP button

panels. The ACP 100 is a US 2-gang size device.

Step 3: Change Plastic Faceplate, Button Labels, or Knob

You can replace the plastic faceplate or one or more of the labels

within the buttons. Some button labels ship with the unit. You can

create and print your own customized labels using Extron

Button Label Generator software from www.extron.com.

To change a plastic faceplate or translucent button label:

1. The plastic faceplate is secured with four magnetic

catches on the underside of the plastic faceplate.

Remove the plastic faceplate by holding the body of

the unit with one hand, gripping the sides of the plastic

faceplate with the other hand, then pulling the plastic

faceplate away from the unit.

2. Gently separate the button lens cap from its white

diffuser. Insert the end of the provided Extron removal

(pry) tool into the corner notch and gently twist the tool

(see 1in the image to the right).

TEXT

Separate the

two-piece button

her

e at the corner.

Dif

fuser

Base

Insert

button label.

Button

Lens Cap

Removal

(Pry) Tool

3. Remove the label insert from the button lens cap.

4. Select one of the button labels from the printed label sheet included with the unit. Remove the label from its backing and

remove the clear protective lm from the front of the label.

5. Insert the button label into the button lens cap (see 2in the image on the previous page).

6. Align the button lens cap with the white diffuser and the panel opening, then press the button lens cap into place on the

button.

7. Attach the plastic faceplate to the ACP 100. Align the openings of the faceplate with the buttons and knob and place the

plastic faceplate against the unit. The four magnetic catches fasten the faceplate onto the unit.

To change a knob:

1. Remove the plastic faceplate as described at the bottom of the previous page.

2. Firmly grasp the knob and pull it away from the ACP 100.

3. Align the ridge inside the new knob with the channel on the knob control and allow the magnet in the knob to snap into place.

4. Reattach the plastic faceplate to the unit as described in step 7 above.

Step 4: Set Bus ID Addresses

Set the bus identication DIP switches for the ACP 100 and any other ACP panels being connected to the system. Each ACP

device must have a unique bus ID (address). If other ACP panels have the same bus ID, address conicts may cause one or more

of the panels to not be recognized in DSP Congurator or by the DMP 128 Plus. Up to four ACP devices can be connected in the

same system.

123456

BUS ID

123456

PWR LOAD = 0.5W

ACP

S+S

+V G

S+S

V+

S G

–

ACP Ports

• Connect up to four (4) ACP endpoint devices per

DMP 128 Plus.

• Wire the connectors the same at both ends.

• These ports are identical. You can connect devices

interchangeably to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP 128 Plus and all of the ACP

panels.

• Power is provided by the DMP 128 Plus, a PS 1220EB

power inserter, or an Extron 12 VDC power supply.

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 100.

• Each ACP connected to the same DMP 128 Plus

must have a unique address.

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• Up = on = 1, Down = off = 0

Examples:

010010

123456

000001

123456

18Unit address

DIP switches

Binary address

ACP Diagnostic LED Indications

LED unlit — No power is present at the ACP.

LED blinking slowly — Power is present, but communication

with the DMP 128 Plus is not confirmed.

LED blinking fast — There is an ACP bus ID address conflict.

LED lit steadily (solid) — Power and communication are

confirmed.

ACP port on a

DMP 128 Plus, or

on another ACP

endpoint

Figure 3. ACP 100 Rear Panel Bus ID

ACP 100 • Setup Guide (Continued)

Each ACP device in a system must have a

unique bus ID which represents a six-digit

binary number. ACP bus IDs are set by using

the DIP switch assembly on the rear panel of

the ACP 100.

Switch 1 on the left sets the most signicant bit (highest number, 32) while switch

6 on the right sets the least signicant bit (the lowest number, 1). See the example

addresses in the table to the right.

Step 5: Cable All Devices

1. Connect the ACP panel to the DMP 128 Plus.

2. Connect ACP panels to each other if multiple panels are being used in the

control system (see gure 4 below for correct wiring).

NOTES:

• Wire both ends of each ACP cable the same. Connectors are

interchangeable between DMP 128 Plus and ACP device.

• Do NOT power an ACP panel from more than one power source.

3. Apply power to the DMP 128 Plus.

Cabling

Attach cables using the diagram below as a guide. Wiring is the same for all ACP

models. Connect a 4-pole captive screw connector to each end of the cable,

wiring both ends the same. In most cases, the ACP devices are powered by the

DMP128Plus. Power is carried on the V+ pin of the ACP 100 and other ACP

devices.

Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device

connections.

Ground

+Signal

Signal

+12 VDC

Black

and

Drains

Green

White

Red

S+S

Drain Wires

Basic ACP Connector Wiring

Figure 4. Basic ACP Connector Wiring

Slide

1 2 3456

BUS ID

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

*Reserved

(for controller

address)

1 2 3456

BUS ID

1 000001

1 2 3456

BUS ID

2 000010

1 2 3456

BUS ID

3 000011

1 2 3456

BUS ID

4 000100

1 2 3456

BUS ID

5 000101

1 2 3456

BUS ID

6 000110

1 2 3456

BUS ID

7 000111

1 2 3456

BUS ID

8 001000

1 2 3456

BUS ID

ACP devices that are relatively far from the host DMP 128 Plus can be connected to an optional Extron PS 1220EB eBUS power

inserter or an Extron 12 VDC desktop power supply as shown in the diagrams below and on the next page (see the ACP 100

Speciﬁcations at www.extron.com for cable length to determine if additional power is recommended).

ATTENTION:

• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory

compliance certification and may cause damage to the supply and the unit.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée

annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked

“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation certifiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,

article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently fixed to

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/

NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être

fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

eBUS 24 WATTS MAX

100-240V 50-60Hz

0.6A MAX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

ACP port on

an ACP or

other ACP

endpoint

device

V+

S G

–

LAN

DMP 128 Plus C

RxTx G

RS-232

+S+V -S G

56 78

12 34

OUTPUTS

DMP EXP

ACP

REMOTE

USB AUDIO RESET

LAN

-23

REMOT

B AUDI

MP 128 Plus

OUTP

DMP E

DMP

DMP 128 Plus

S+S

Tie drain wires

to ground.

S+S

Ground

+Signal

Signal

+12 VDC

S+S

ACP Connections

• Connect up to four (4) ACP

endpoint devices to the PS 1220EB.

• Wire the connectors the same at

both ends.

• All ports are identical and

interchangeable.

Power Input

(100-240 VAC,

50-60 Hz)

PS 1220EB

ATTENTION: Do NOT connect the power

pin to any device that is already powered

by the DMP 128 Plus or by an additional

power suppl y.

3/16" (5 mm) Max.

Figure 5. Cabling ACP Devices with a PS 1220EB Power Inserter

ACP 100 • Setup Guide (Continued)

ACP port on a

host DMP 128

Plus

V+

S G

–

ACP port on

an ACP 100

or other ACP

device

V+

S G

–

Ground

+Signal

Signal

+12 VDC

G-S+SG-S+S

Tie drain wires to ground.

Ground

all devices.

– Return

+12 VDC input

Ridged

Smooth

1AMAX

100-240V 50-60Hz

External

Power Supply

(12 VDC, 1 A max.,

Extr

on P/N 28-071-57LF)

ACP 100

Rear Panel

NOTE:

Check the polarity of the power

supply before connecting it to the ACP.

Power Input,

External Power Supply (optional)

• Connect to an Extron 12 VDC, 1 A,

power supply.

3/16" (5 mm) Max.

Figure 6. Cabling ACP Panels with an Extron 12 VDC, 1 A Power Supply

Step 6: Conﬁgure the System

NOTE: For complete information on creating configuration files and operating DSP Configurator, see the DMP 128 Plus User

Guide and the DSP Configurator Help file.

1. Create a new DMP 128 Plus conguration le in DSP Congurator and create all groups, presets, and macros that will be

controlled by the ACP device.

2. Open the Configure ACPs dialog box in DSP Congurator and congure the buttons on the ACP devices connected to

the DMP 128 Plus.

3. Connect to the DMP 128 Plus in Live mode and push the conguration le to the device.

Step 7: Test and Troubleshoot

1. Verify that the DIP switches on the ACP devices are set to the desired address on each unit and that there are no bus ID

address conicts in the system. As mentioned in the rear panel features diagram in step 4, the ACP LED lights steadily

when power and communication are present and there are no bus ID address conicts.

2. Verify cables to and from the ACP devices are wired the same at each end.

3. Test the system:

a. Press the buttons on the ACP devices and ensure the buttons light as desired and that the appropriate control

commands or functions are triggered. Commands can be veried in DSP Congurator or DataViewer, if responses are

congured.

b. Ensure that the audio output responds correctly to the volume knob. Also ensure that the volume LEDs light correctly

as you increase or decrease audio gain.

4. Make adjustments to wiring, bus ID addresses, or system conguration as needed. Remember that the rear panel ports and

DIP switches will not be accessible after the ACP is mounted. If needed, push a revised conguration to the ACP device via

the host DMP 128 Plus.

If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3

Control Systems Support Hotline (1.800.633.9877).

ACP 100 • Setup Guide (Continued)

Step 8: Mounting the ACP 100

Prior to mounting:

1. If it has not already been done, feed all device cables through the wall or furniture and, if applicable, through the plastic

spacer.

NOTE: If the unit is not installed in a mud ring, you must install the plastic spacer. The spacer positions the unit to allow

the magnetic catches on the plastic faceplate to attach properly and securely.

2. Ensure the cables are connected to the ACP 100 rear panel.

Mount the ACP 100 as follows:

1. Insert the cabled ACP 100 into the mud ring or junction box within the wall or furniture, aligning the mounting holes in the

ACP 100 with those in the box or mud ring.

2. Secure the ACP 100 in the junction box, wall or surface mounting box, or mud ring as follows (see 1in the gures below).

a. Insert the included screws through the oval slots at the top and bottom of the ACP 100 metal mounting plate, through

the plastic spacer (if not using a mud ring), and into the corresponding threaded holes in the box or mud ring.

b. Using a Phillips screwdriver, gently tighten the screws until snug.

3. Attach the plastic faceplate to the ACP 100. Align the plastic

faceplate openings with the buttons, knob, and LEDs and

place the plastic faceplate against the metal mounting

plate (see 2in the gures below). The magnetic

catches fasten the plastic faceplate onto the

metal mounting plate.

Extron

VOLUME

Wall

Box

Plastic

Faceplate

Metal Mounting

Plate

Plastic Spacer

Extron

VOLUME

Metal Mounting

Plate

Wall Mounting

Bracket

(Mud Ring)

Plastic

Faceplate

Wall

Figure 7. Installing the ACP 100

in a Junction Box

Figure 8. Installing the ACP 100

in a Mud Ring

68-3065-50 Rev. A

01 17

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

EExtron Australia

+61.8.8113.6800

+61.8.8351.2511 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Table des matières

Autres manuels Extron electronics Panneau de contrôle

Extron electronics

Extron electronics MMX 32 AAP Manuel utilisateur

Extron electronics

Extron electronics SCP 104 Series Manuel utilisateur

Extron electronics

Extron electronics ACP VC1 D Manuel utilisateur

Extron electronics

Extron electronics MLC 55 RS Manuel utilisateur

Extron electronics

Extron electronics MCP 1000 Manuel utilisateur

Extron electronics

Extron electronics ACP 106 D Manuel utilisateur

Extron electronics

Extron electronics RCP 2000 Manuel utilisateur

Extron electronics

Extron electronics MKP 2000 Manuel utilisateur

Extron electronics

Extron electronics Control Panel CTL208CM Manuel utilisateur

Extron electronics

Extron electronics SCP 100P Manuel utilisateur

Extron electronics

Extron electronics IP Link Pro NBP 50 Manuel utilisateur

Extron electronics

Extron electronics CTP150CM Manuel utilisateur

Extron electronics

Extron electronics TLP Pro x25M Series Manuel utilisateur

Extron electronics

Extron electronics eBUS Button Panel EU Series Manuel utilisateur

Extron electronics

Extron electronics TouchLink Pro Series Manuel utilisateur

Extron electronics

Extron electronics SCP 250 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 320C Manuel utilisateur

Extron electronics

Extron electronics RCP 2000 Manuel utilisateur

Extron electronics

Extron electronics RCP 101 D Manuel utilisateur

Extron electronics

Extron electronics MKP 3000 Manuel utilisateur

Extron electronics

Extron electronics Decorator-Style Series Manuel utilisateur

Extron electronics

Extron electronics SCP 150L Manuel utilisateur

Extron electronics

Extron electronics MCP 1000 Manuel utilisateur

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques