Extron electronics ACP 106 D Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 106 D • Setup Guide

The Extron ACP 106 D Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled device.

Each ACP 106 D includes two ACP ports, which support power and communication between the host device and the ACP 106 D.

Up to eight ACP panels can be used per host device for more demanding control needs.

Front Panel Features

Extron

PROGRAM

MIC

VOLUME

MUTE

AMute Buttons

BTransmit LED

CVolume Buttons

DVolume LED Meter

EFunction Button 1

FFunction Button 2

Figure 1. ACP 106 D Rear Panel

Rear Panel Features

ACP

PWR LOAD = 1.5W

+S -S G +V +S -S G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

AA B

AACP Ports (2)

BConnection Status LED

CReset Button

DBus ID DIP Switches

Figure 2. ACP 106 D Front Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see the

ACP 106 D product page at www.extron.com for more information about the ACP 106 D).

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 106 D installation.

ACP 106 D • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 106 D into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 106 D dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 106 D will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access

hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 106 D dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualifié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 106 D must

be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the

ACP106 D.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP 106 D is a US 1-gang size device.

Step 3: Removing the Plastic Faceplate, Button Panel, and Changing the Buttons

The plastic faceplate and buttons can be replaced. Additional buttons ship with the

device and others can be ordered from www.extron.com.

To change the buttons:

1. Remove the two screws holding the plastic faceplate to the metal mounting

plate and separate the faceplate from the button plate (see 1in the gure to

the right).

2. Insert a small at-bladed screw driver into the notch at the top of the button

plate. Release the catch holding the button plate to the metal mounting plate

(2).

3. Repeat step 2 to release the catch at the bottom of the plate.

4. Tilt the top of the button plate forward as it is removed to prevent the buttons

from falling out.

Extron

VOLUME

MUTE

MIC

PROGRAM

ACP 106 D

Face plate

5. To remove a button, press a button backward through its slot in the

button plate until the membrane containing the button is free (see 1in

the gure to the right).

6. To replace a button, align the two pegs in the button membrane with the

holes located at opposite corners of the empty slot on the back of the

button faceplate and push the button forward so it ts in the desired slot

(see 2in the gure to the right). Ensure the button text orientation is

correct.

7. Repeat steps 5 and 6 to replace any other buttons.

8. Align the button plate with the metal mounting plate using the pegs on

the rear of the button plate as guides.

9. Snap the button plate into place.

10. Reattach the plastic faceplate using the two screws removed in step 1.

Step 4: Set Bus ID Addresses

+VG

+S-S+VG

+S-S

ACP

PWR LOAD = 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

V+

S G

–

ACP port on a

DMP Plus, or on

another ACP

endpoint

ACP Ports

• Connect up to eight (8) ACP endpoint devices per

DMP Plus.

• Wire the connectors the same at both ends.

• These ports are identical. You can connect devices

interchangeablly to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP Plus and all of the ACP

panels.

• Power is provided by the IPCP Pro, a PS 1220EB power

inserter, or an Extron 12 VDC power supply.

010010

123456

000001

123456

Unit address

DIP switches

Binary address

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 106 D.

• Each ACP connected to the same DMP Plus

must have a unique address.

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• Up = on = 1, Down = off = 0

Examples:

Figure 3. ACP 106 D Rear Panel and Side Bus ID DIP Switch Assembly

Set the bus identication (bus ID) DIP switches for the ACP 106 D

and any other ACP panels being connected to the system. Each ACP

device must have a unique bus ID. If multiple panels have the same bus

ID, address conicts may cause one or more of the panels to not be

recognized in DSP Congurator or by the host device. Up to eight ACP

devices can be connected in the same system.

Each ACP device in a system must have a unique six-digit binary bus ID.

ACP bus IDs are set using the DIP switch assembly on the left side of the

ACP 106 D (see gure 3).

Switch 1 on the left sets the most signicant bit (highest number, 32)

while switch 6 on the right sets the least signicant bit (the lowest

number, 1). See the example addresses to the right.

Slide

1 2 3456

BUS ID

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

1 2 3456

1 000001

1 2 3456

2 000010

1 2 3456

3 000011

1 2 3456

4 000100

1 2 3456

5 000101

1 2 3456

6 000110

1 2 3456

7 000111

1 2 3456

8 001000

1 2 3456

*Address 000000 is reserved for the control processor and cannot be used by any ACP devices.

ACP 106 D • Setup Guide (Continued)

Step 5: Cable All Devices

1. Connect the ACP panel to the host device.

2. Connect ACP panels to each other if multiple panels are being used in the control system (see the wiring diagram below for

correct wiring).

NOTES:

• Wire both ends of each ACP cable the same. Connectors are interchangeable between the host device and ACP

device.

• Do NOT power an ACP panel from more than one power source.

3. Apply power to the host device after correctly cabling all devices.

Cabling

Attach cables using the diagram below as a guide. Wiring is the same for all ACP models. Connect a 4-pole captive screw

connector to each end of the cable, wiring both ends the same. In most cases, the ACP devices are powered by the DMPPlus

series device. Power is carried on the V+ pin of the ACP 106 D and other ACP devices.

Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device connections.

Ground

+Signal

Signal

+12 VDC

Black

and

Drains

Green

White

Red

S+S

Drain Wires

Basic ACP Connector Wiring

ACP devices that are relatively far from the host device can be connected to an optional Extron PS 1220EB eBUS power

inserter or an Extron 12 VDC desktop power supply as shown in the diagrams below and on the next page (see the ACP 106 D

Speciﬁcations at www.extron.com for cable length to determine if additional power is recommended).

ATTENTION:

• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory

compliance certification and may cause damage to the supply and the unit.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée

annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked

“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation certifiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,

article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently fixed to

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/

NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être

fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

eBUS 24 WATTS MAX

100-240V 50-60Hz

0.6A MAX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

ACP port on

an ACP or

other ACP

endpoint

device

V+

S G

–

LAN

DMP 128 Plus C

RxTx G

RS-232

+S+V -S G

5 6 7 8

1 2 34

OUTPUTS

DMP EXP

ACP

REMOTE

USB AUDIO RESET

DMP 128 Plus

S+S

Tie drain wires

to ground.

S+S

Ground

+Signal

Signal

+12 VDC

S+S

ACP Connections

• Connect up to eight (8) ACP

endpoint devices to the PS 1220EB.

• Wire the connectors the same at

both ends.

• All ports are identical and

interchangeable.

Power Input

(100-240 VAC,

50-60 Hz)

PS 1220EB

ATTENTION: Do NOT connect the power

pin to any device that is already powered

by the DMP Plus or by an additional

power supply.

3/16" (5 mm) Max.

Figure 4. Cabling ACP Devices with a PS 1220EB Power Inserter

Exter

nal Power Supply

(12 VDC, 2.0 A)

ACP 106 D

Rear Panel

Tie drain wires to ground.

Ground

all Devices

RidgedSmooth

3/16" (5 mm) Max.

ACP port on

a host DMP

Plus

ACP port on

an ACP or

other ACP

Endpoint

NOTE:

Check the polarity of the power

supply before connecting it to the ACP.

V+

S G

–

V+

S G

–

Ground

+Signal

Signal

Ground

+Signal

Signal

+12 VDC

– Return

+12 VDC input

P 106 D

ear

ane

+VG

+S-S+VG

+S-S

ACP

PWR LOAD = 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Power Input, External Power Supply (optional)

• Connect to an Extron 12 VDC, 2.00 A, power supply.

Figure 5. Cabling ACP Panels with an Extron 12 VDC Power Supply

ACP 106 D • Setup Guide (Continued)

Step 6: Conﬁgure the System

NOTE: For complete information on creating configuration files and operating DSP Configurator, see the host device user

guide and the DSP Configurator Help file.

1. Create a new host device conguration le in DSP Congurator and create all groups, presets, and macros to be controlled

by the ACP device.

2. Select Tools>Configure ACPs in DSP Congurator and congure the ACP button actions and panel IDs.

3. Connect to the host device in Live mode with a TCP/IP connection and push the conguration le to the device.

Step 7: Test and Troubleshoot

1. Verify the ACP bus ID DIP switches are set to the desired address on each unit and that there are no bus ID address conicts

in the system.

The ACP 106 D has a rear panel LED that can be used as a diagnostic tool. Your model may have a single monochrome LED

(green) or a single bicolor LED that can light green, amber, or red (amber + green). The device status indicated by the LED is

shown in this table:

Device Status Single LED (green) Single LED (bicolor)

No power, ACP cable broken. Off Off

Device is receiving power and communicating correctly

with the DMP Plus.

Lights solidly Lights green

Device is receiving power but cannot communicate with

the DMP Plus.

Slow blink Lights amber

Device is receiving power and communicating with the

DMP Plus but there is an address conflict.

Fast blink Lights red

2. Verify cables to and from the ACP devices are wired the same at each end.

3. Test the system:

a. Press the ACP device buttons and ensure the buttons light as expected and that the appropriate control actions are

triggered. Commands can be veried using DSP Congurator. DataViewer can also be used for command verication if

responses are congured.

b. Ensure the audio levels respond correctly to the volume and mute buttons.

4. Make adjustments to wiring, bus ID addresses, and system conguration as needed. Remember that the rear panel ports and

DIP switches are not accessible after the ACP is mounted. If needed, push a revised conguration to the ACP device through

the host device using DSP Congurator.

If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3

Control Systems Support Hotline (1.800.633.9877).

Step 8: Mounting the ACP 106 D

Prior to mounting:

1. Feed all device cables through the wall or furniture.

NOTE: If the unit is not installed in a mud ring, you must install the plastic spacer. The spacer positions the unit to allow

the plastic faceplate to attach properly and securely.

2. Ensure the cables are connected to the ACP 106 D rear panel.

To mount an ACP 106 D with a wall mounting bracket (mud ring):

1. Mark the position of the hole for the wallplate on desired

wall location. Use a level to ensure the hole is marked at the

correct angle.

2. Use a drywall saw to cut the hole for the wallplate (see 1in

the gure to the right).

3. Insert the mounting bracket (mud ring) into the hole and use

a screw driver to turn and tighten the locking arms until they

clamp the mud ring to the mounting surface (2). Do not

overtighten.

4. If not already done, set bus ID DIP switches so the panel has a

unique bus ID (3).

5. Use the two provided screws to secure the metal mounting

plate to the mud ring (4).

6. Use the other two provided screws to secure the plastic

faceplate to the metal mounting plate (5).

To mount an ACP 106 D with a junction box:

1. Install the junction box following the instructions provided with

the chosen junction box. No junction box is included with the

ACP 106 D.

2. Locate a suitable wall stud and mark the location of the hole

on the wall. Use a level to ensure the hole is marked at the

correct angle.

3. Use a drywall saw to cut the hole. Follow the instructions of

the junction box manufacturer for the correct dimensions of

the hole. Use at least two screws or nails to secure the box to

the wall or stud. Follow steps 4 through 6 above to complete

the installation.

Wall

Wall Mounting

Bracket

Extron

VOLUME

MUTE

Plastic

Faceplate

ACP 106 D

MIC

PROGRAM

Electrical

Junction

Box

Extron

VOLUME

MUTE

ACP 106 D

MIC

PROGRAM

Plastic

Faceplate

68-3066-50 Rev. B

07 19

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Table des matières

Autres manuels Extron electronics Panneau de contrôle

Extron electronics

Extron electronics SCP 150L Manuel utilisateur

Extron electronics

Extron electronics ECP 1000 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 320C Manuel utilisateur

Extron electronics

Extron electronics Control Panel CTL208CM Manuel utilisateur

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manuel utilisateur

Extron electronics

Extron electronics Decorator-Style Series Manuel utilisateur

Extron electronics

Extron electronics MKP 2000 Manuel utilisateur

Extron electronics

Extron electronics MLC Plus 84 EU Manuel utilisateur

Extron electronics

Extron electronics MKP 2000 Manuel utilisateur

Extron electronics

Extron electronics SCP 200 Manuel utilisateur

Extron electronics

Extron electronics TLP Pro 320C Manuel utilisateur

Extron electronics

Extron electronics ACP 100 Manuel utilisateur

Extron electronics

Extron electronics MLC 55 RS Manuel utilisateur

Extron electronics

Extron electronics MCP 1000 Manuel utilisateur

Extron electronics

Extron electronics RCP 101 D Manuel utilisateur

Extron electronics

Extron electronics TouchLink Pro Series Manuel utilisateur

Extron electronics

Extron electronics ACP 105 D Manuel utilisateur

Extron electronics

Extron electronics MCP 1000 Manuel utilisateur

Extron electronics

Extron electronics IPCP Pro Series Manuel utilisateur

Extron electronics

Extron electronics ACP 100 Manuel utilisateur

Extron electronics

Extron electronics ACP VC1 D Manuel utilisateur

Extron electronics

Extron electronics MKP 3000 Manuel utilisateur

Extron electronics

Extron electronics MMX 32 AAP Manuel utilisateur

Extron electronics

Extron electronics ACP VCI EU/MK Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques