Extron electronics DMP 64 Manuel utilisateur

DMP 64 Setup Guide

68-1790-50 Rev. A

10 09

PRELIMINARY

Receive (Rx)

Transmit (Tx)

Ground ( )

Bidirectional

RS-232

Device

Ground ( )

Receive (Rx)

Transmit (Tx)

RxTx

Do not tin

the wires!

Step 1 — Disconnect power

Disconnect power to the DMP 64 and turn off all devices that will be connected to it.

Step 2 — Mount the DMP 64

The DMP 64 is housed in a 1/2 rack width, 9.5" deep, 1U high metal enclosure. Select a suitable mounting location,

then choose an appropriate mounting option. See Chapter 2, "Installation", for additional information.

Step 3 — Cable the Digital Matrix Processor

Run all audio, communication and power cables for operation to the rear panel.

Step 4 — Connect the Mic/Line inputs

Attach up to 6 mic or mono line level devices, balanced or unbalanced, to

the DMP 64 using the wiring diagram to the right.

Step 5 — Connect the audio outputs

For balanced or unbalanced mono audio output, connect an audio output

device to each of the four outputs. Use the wiring diagram to the right.

Step 6 — Connect the I/O ports

To control or monitor external devices, connect up to 6 digital I/O ports. See

Chapter 3, "Rear Panel Operation" and Chapter 5, "Digital I/O Ports" for

additional information.

Step 7 — Connect a control system

Extron recommends using the LAN port for conﬁguration and remote

control of the DMP 64. However there are three options; RS-232,

USB and LAN. See Chapter 2, "Rear Panel Features and Cabling"

for additional information.

RS-232 — Connect the host RS-232 cable to the 3-pin captive screw

connector on the rear of the switcher.

USB — Connect the host USB port to the front conﬁguration port

using a USB to mini-USB cable.

LAN — Using a standard ethernet cable, connect to the network via

the LAN port (i). To connect the DMP 64 directly to a computer,

use a crossover ethernet cable. The table at right shows the default

network settings.

POWER

12V

1.5A MAX

RESET

LAN

MIC/LINE INPUTS

Tx Rx

RS-232(1)

I/O

MIC

+48V

Tx Rx

RS-232(2)

456

123

456

DMP 64

h d e f g g

BalancedUnbalanced

Tip

Ring

Sleeve

Tip

Sleeve

Do not tin the wires!

Digital I/O Wiring

This guide provides basic instructions for an experienced technician to install the DMP 64 ProDSP™ Digital Matrix Processor.

Where possible in the following pages, line drawings and photos from an actual installation are used to clarify steps

discussed in the text. Where appropriate, images have one or more numbers corresponding to a speciﬁc step described.

Chapter number and titles reference the DMP 64 User's Manual found at www.extron.com.

IP Address: 192.168.254.254

Subnet Mask: 255.255.0.0

Default Gateway: 0.0.0.0

DHCP: OFF

DMP 64 Setup Guide, Continued

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Step 8 — Wire the power supply

Wire the included power supply using the diagram on the right. Plug

the captive screw connector into the DMP 64 power jack (j)

To obtain the Windows-based software and the User's Manual from the DVD

1. Insert the disk provided into the computer’s DVD ROM drive. If the setup program does not start automatically, run

Launch.exe from the DVD ROM directory using Windows “My Computer”. The opening screen will appear with the

following tabs:

2. For the User's Manual, select the Manuals tab, then select the DMP 64 User's Manual from the list of available documentation.

The manual, in PDF format, will open in the browser window or can be downloaded to the hard drive for future reference.

3. To download the DSP Conﬁgurator program, select the Software tab menu.

4. From the Downloads page, on the DMP Conﬁgurator row, (the downloads are listed in alphabetical order), select Install.

5. Choose Run and the DMP Conﬁgurator will install. In most cases it is best to accept the default installation suggestions.

6. When the DSP Conﬁguration program completes installation, the USB driver must be installed. Whether planning to use

the USB conﬁguration port or not, it is recommended to install it. Click Next on the USB Driver Installer and follow the

on-screen instructions.

7. When the USB driver installation completes, remove the DVD from the drive and reboot the computer.

8. Launch the DSP Conﬁgurator program from the Extron Software group in the Start Programs menu. Select "DMP 64" when

the model options become available. The DSP Conﬁgurator Help ﬁle contains all operation details for the software.

Step 10 — Install the software

There are no hardware controls for the DMP 64. All conﬁguration and

control is done via software. The control software, DSP Conﬁgurator,

is available on the included disc. If there is a card with the device

stating the DVD does not contain the software or user's manual,

both are available from the Extron website at www.extron.com. The

control software Help ﬁle contains all operation descriptions.

Step 9 — Power up the DMP 64

Power up the input and output devices, then connect power to the

DMP 64.

SECTION A–A

Power Supply

Output Cord

Ridges

Smooth

Ridges

Smooth

2-P

ole Orange

Captive Screw

Connector

(12V)

Tie Wrap

3/16”

(5 mm) Max.

To obtain the software and User's Manual from the website

1. Using any internet browser go to www.extron.com.

2. From the Extron home page select the DMP 64 from the Product Shortcuts.

3. Select the Downloads tab on the DMP 64 product page.

4. Select the User's Manual from the list of available documentation and click on it to either view or download it to the hard

drive for future access.

5. To download the control software, on the Downloads tab, select DSP Configurator.

6. The link transfers to the selected software download page. Fill out the form, then download the software to the hard drive.

7. When the download is complete, locate the ﬁle (DSP_ConﬁguratorSetupV.x.x.x.x.exe) on the hard drive and double-click.

The ﬁle is a self-executing installation program. In most cases it is best to accept the default installation suggestions.

8. Proceed to Step 6 of the DVD installation instructions above.

Autres manuels pour DMP 64

Autres manuels Extron electronics Matériel informatique

Extron electronics

Extron electronics SMP 300 Series Manuel utilisateur

Extron electronics

Extron electronics DTP3 T 202 Manuel utilisateur

Extron electronics

Extron electronics MTP 15HD RS Series Manuel utilisateur

Extron electronics

Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W... Manuel utilisateur

Extron electronics

Extron electronics EDID 101D Manuel utilisateur

Extron electronics

Extron electronics Annotator 300 Manuel utilisateur

Extron electronics

Extron electronics DMP 128 FlexPlus Manuel utilisateur

Extron electronics

Extron electronics EDID 101H 4K PLUS Manuel utilisateur

Extron electronics

Extron electronics IPCP 505 Manuel utilisateur

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Manuel utilisateur

Extron electronics

Extron electronics DMP Plus Series Manuel utilisateur

Extron electronics

Extron electronics SC 210 Manuel utilisateur

Extron electronics

Extron electronics XMP 240 C AT Manuel utilisateur

Extron electronics

Extron electronics DMP 128 Plus Manuel utilisateur

Extron electronics

Extron electronics IPCP Pro Series Manuel utilisateur

Extron electronics

Extron electronics HAE 100 4K Manuel utilisateur

Extron electronics

Extron electronics WindoWall Pro Series Manuel utilisateur

Extron electronics

Extron electronics DVI Output Card Manuel utilisateur

Extron electronics

Extron electronics Annotator 300 Manuel utilisateur

Extron electronics

Extron electronics Quantum Ultra Series Manuel utilisateur

Extron electronics

Extron electronics IPL Pro S1 Manuel utilisateur

Extron electronics

Extron electronics StudioStation 100 Manuel utilisateur

Extron electronics

Extron electronics EDID 101H 4K PLUS Manuel utilisateur

Extron electronics

Extron electronics DMP 44 LC Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur