Extech Instruments TK30 Manuel utilisateur

Owner’s Guide

Model TK30

True RMS Professional Electrical HVAC MultiMeter Test Kit

Introduction

Congratulations on your purchase of the Extech Model TK30 MultiMeter Test Kit. This kit is

housed in a lightweight protective case and includes a MultiMeter, Clamp On Adaptor,

Voltage Detector, Line Splitter, Temperature Probe, and Cables. Operation instructions for

these units are detailed in the supplied manuals and are beyond the scope of this guide.

Model TK30 Version 1.2 July 2002

Contents of Kit

•Model MT330 True RMS MultiMeter

•Model CA330 300A AC Current Clamp

•Model 480172 AC Line Splitter

•Model 40130 Voltage Detector

•Set of 1000V Category III test leads

•Type K thermocouple temperature probe

•Model CA900 Carrying Case

•Operation Manuals for the Models MT330, CA300, and TK30

Current Clamp with MultiMeter

The Current Clamp connects to the MultiMeter as shown and can be used to measure

current for the ranges listed in the Current Clamp’s specifications.

Operation

1. Connect the Current Clamp test

leads to the COM and V inputs of

the MultiMeter.

2. Set the MultiMeter to the V function

range

3. Press the DC/AC button to select

AC (“AC” appears in the display).

4. Press the RANGE button until the

milliVolt range is selected (“mV”

appears in the display).

5. If the anticipated current is less than 10A, zero the meter using the REL button. (see

zeroing note)

6. Clamp around the conductor under test and read the current measurement on the

meter’s LCD.

7. The Clamp outputs 1mV AC for each Ampere of current measured.

Note: The zero offset voltage is approximately 5mV and this voltage is not linear. The

offset will affect low current measurements, but will have little affect on high current

measurements. For the best measurement accuracy, press the Relative button to

zero the meter for currents <10A. Do not zero the meter for currents higher than

10A.

Interpreting the Display

Display Current

005.0 mV 5 amps

020.0 mV 20 amps

250.0 mV 250 amps

3.999

300 AMP AC CLAMP ADAPTOR

OUTPUTVOLTAGE: 1mV AC Per 1A AC

CATII600V

CA300

Model TK30 Version 1.2 July 2002



Support Hotline (781) 890-7440

Tech support: Ext. 200; Email: [email protected]

Repair/Returns: Ext. 210; Email: [email protected]

Website: www.extech.com

Current Clamp and Line Splitter

Line Splitter

The supplied Line Splitter provides a means to cleanly

“open” a standard 120V line cord in order to make clamp

type current measurements. When connected between the

120V AC wall outlet and the device under test, the Current

Clamp can then be clamped on one of the two test

openings in the Splitter. One opening provides a one-to-

one current reading and the other provides a times-ten

(X10) reading so that small current will display with better

resolution on the MultiMeter.

Line Splitter Operation:

Current Measurements

1. Plug the AC Line Splitter into the 120V receptacle

2. Plug the line cord from the load into the AC Line Splitter socket

3. Close the Clamp-on jaws around either the X1 or X10 arm of the AC Line Splitter

4. If the X1 position is used, read the current directly on the meter

5. If the X10 position is used, divide the meter reading by 10 to obtain the actual

current

Voltage Measurements

1. Plug the AC Line Splitter into the 120V receptacle

2. Insert the multimeter test leads into the two Voltage Test jacks

3. Read the voltage on the multimeter

VOLTAGE TEST

LINE SPLITTER

Table des matières

Autres manuels Extech Instruments Équipement de test

Extech Instruments

Extech Instruments 382356 Manuel utilisateur

Extech Instruments

Extech Instruments ET60 Manuel utilisateur

Extech Instruments

Extech Instruments ET30B Manuel utilisateur

Extech Instruments

Extech Instruments 422123 Manuel utilisateur

Extech Instruments

Extech Instruments 480303 Manuel utilisateur

Extech Instruments

Extech Instruments CT70 Manuel utilisateur

Extech Instruments

Extech Instruments CB10 Manuel utilisateur

Extech Instruments

Extech Instruments 380260-NIST Manuel utilisateur

Extech Instruments

Extech Instruments 480403 Manuel utilisateur

Extech Instruments

Extech Instruments ET20B Manuel utilisateur

Extech Instruments

Extech Instruments CG204 Manuel utilisateur

Extech Instruments

Extech Instruments HDV540 Manuel utilisateur

Extech Instruments

Extech Instruments MG320-NIST Manuel utilisateur

Extech Instruments

Extech Instruments BR90 Manuel utilisateur

Extech Instruments

Extech Instruments ET23B Manuel utilisateur

Extech Instruments

Extech Instruments ET25 Manuel utilisateur

Extech Instruments

Extech Instruments PRC15 Manuel utilisateur

Extech Instruments

Extech Instruments CB10 Manuel utilisateur

Extech Instruments

Extech Instruments MG325 Manuel utilisateur

Extech Instruments

Extech Instruments 412300A Manuel utilisateur

Extech Instruments

Extech Instruments TK32 Manuel utilisateur

Extech Instruments

Extech Instruments 407744 Manuel utilisateur

Extech Instruments

Extech Instruments 407744 Manuel utilisateur

Extech Instruments

Extech Instruments BR146 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur