Extech Instruments PRC15 Manuel utilisateur

USER GUIDE

Current / Voltage Calibrator

Model PRC15

2PRC15-EU-EN-V1.2 01/13

Introduction

Thank you for selecting the Extech Model PRC15. This device is shipped fully tested and calibrated

and, with proper use, will provide years of reli able service. Please visit the Extech Instruments

website (www.extech.com

) to check for the latest version of this User Guide. E xtech Instruments is

an ISO-9001 certified company.

Safety

International Safety Symbols

This symbol, adj acent to another symbol or term inal, indicates the user must refer to the

manual for further information.

This symbol, adjacent to a terminal, indica tes that, under normal use, hazardous voltages

may be present

Double insulation

Safety Notes

Do not exceed the maximum allowable input range.

Turn the unit OFF when the device is not in use.

Remove the batteries if the device is to be stored for longer tha n 60 days.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

Cautions

Improper use of this meter can cause damage, shock, injury or death. Read and understand

this user manual before operating the meter.

Always remove the test leads before replacing the battery.

Inspect the condition of the test leads and the meter itself for any damage before operating the

meter. Repair or replace any dam age before use.

If the equipment is used in a manner not specifi ed b y the manufacturer, the protecti on provided

by the equipment may be impaired.

3PRC15-EU-EN-V1.2 01/13

Meter Description

1. AC adaptor input jack

2. Display

3. Power ON/OFF

4. Source output adjustment arrow buttons

5. Set button

6. Unit button (mA or %)

7. I/O MODE button

8. MEM (memory STEP button)

9. Backlight/ZERO button

10. Test lead input jacks

Display Layout

1. SOURCE mode icon

2. ZERO function status icon

3. MEASURE mode icon

4. Auto Power OFF active icon

5. Battery status icon

6. Measure mode value

7. Measure mode units icon

8. Datalogger memory location

9. Source mode value

10. Source mode units icon

4PRC15-EU-EN-V1.2 01/13

Keypad Descriptions and Operation

POWER BUTTON and AUTO POWER OFF FEATURE

1. Use the POWER button to turn the unit ON or OFF . When the unit is powered up, a short

self-test will ensue after which the display will stabilize.

2. When the battery symbol flashes on the displa y, replace the battery as soon as possible.

Low battery power may cause inaccurate readings and erratic meter operation.

3. This instrument is equipped with Auto Power OFF which turns the meter off after 10 minutes

of inactivity. To override this feature; press and hol d the POWER button until the display

icon “ATP” turns off.

UNIT BUTTON

Press the UNIT button in the current function to select mA or %units or V or mV in the voltage

function. Voltage is autoranging in the MEASURE mode.

I/O BUTTON

Momentarily press the I/O button to select either SOUR CE (output) or MEASURE (input).

MODE BUTTON

In the MEASURE mode, Press and Hold the MODE (I/O) button for 1secondto select either the

current (mA/%) or voltage (mV/V) function. Release the button when the desired function appears.

(Backlight) BUTTON

Press the Backlight button to turn the backlight on or off.

ZERO ( ) BUTTON

In the MEASURE or SOURCE m ode, Press and Hold the ZERO ( ) button fo r 1 second to zero

the meter.

►◄▼and ▲BUTTONS

The arrow buttons are used to set the output value in the SOURCE mode.

1. Select the SOURCE mode

2. Press the ►or ◄button select a digit for adjustment. The blinking underline curser

identifies the digit selected.

3. Press the ▼or ▲button to adjust the value of the digit. Press and Hold the ▼or ▲button to

rapidly adjust the value.

5PRC15-EU-EN-V1.2 01/13

SET BUTTON

The SET button is used to manually step through the 5 stored outp ut values.

1. Select the SOURCE mode

2. Press the SET button and the value stored in me mory location 01 will be sourced. “MEM.01”

appears in the display.

3. Each press of the SET button will step t hrough the 5 memory locations.

4. The arrow buttons can be used to adjus t the value in each memory location.

STEP/MEM BUTTON

The STEP/MEM button is used to automatically step through the 5 stored outpu t values. The meter

can be set for a single cycle of the st ored values or a continuous cycle.

1. Select the SOURCE mode

2. Press and HOLD the STEP/MEM button. ”STEPSS” (single cycle) and “STEPSC ”

(continuous cycle) will alternately appear in the dis play. Release the button when th e

desired mode is displayed.

3. In single cycle mode t he meter will source the current or voltage displayed in MEM01 for 5

seconds. The meter will then advance to MEM 02 for 5 seconds. This will continue through

MEM

05 and then step down through the memory l ocations. The c ycle will end when MEM01

has been reached.

4. In the continuous mode the cycle will continue until manuall y stopped.

5. Momentarily press the MEM button to stop the c ycle. “END” will briefly appear in the display.

STORING VALUES INTO MEMORY

The default values stored in the memor y locations are:

Memory

Location

mA % mV V

4.00mA 0.0% 0mV 0V

8.00mA 25% 500mV 5V

12.00mA

6PRC15-EU-EN-V1.2 01/13

Modes of Operation

MEASURE (Input) Mode of Operation

In this mode, the unit will measure up to 50mADC or 20VDC.

1. Turn the meter ON.

2. “MEASURE” will appear in the display.

3. Press and Hold the MODE button for 1 second to s elect mA or % or mV

4. Connect the Calibration Cable to the meter.

5. Connect the Calibration Cable to the device or circuit under test.

6. Read the measurement on the LCD display.

SOURCE (Output) Mode of Operation

In this mode, the unit can source current up to 24mADC at 1000 ohms or voltage up to 20.00V.

The current or voltage can be output either ma nually or stepped from memory as described

earlier.

1. Turn the meter ON

2. MEASURE” will appear in the display.

3. Press and Hold the MODE button for 1 second to select mA or % or mV

4. Momentarily press the “I/O” button to select SOURCE.

5. Press the UNIT button to select % / mA or mV / V.

6. Connect the Calibration Cable to the meter

7. Connect the Calibration Cable to the device or circuit under test

8. Use the

arrow buttons to set the desired output v alue in the lower display. The upper

display indicates the actual curren t or voltage value being sourced. If the upper display does

not match the set value, either the batteri es need to be replaced or the load impedance is

beyond the specified range.

7PRC15-EU-EN-V1.2 01/13

Tilt Stand / Hanger

The rear stand is provides two met hods for convenienc e in viewing.

1. Pull the bottom portion of the stand out to place the unit on a flat surface for viewing.

2. Pull the bottom and top portions of the stand out, a nd then rotate th e stand to allow the unit

to be hung.

Battery Replacement

When the battery icon appears on the display, the six AA batteries m ust be replaced.

The battery compartment is located on the rear of the meter.

1. Open the tilt stand, loosen the captive Philips head screw and remov e the battery cov er.

2. Remove and replace the ba tteries, observing polarity.

3. Replace and secure the batter y cover.

All EU users are legally bound by the Battery Ordinance to ret urn all used batteries to

community collection points or wherever batteries / accumulators are sold.

Disposal in household trash or refuse is prohibited.

Disposal: Follow the valid legal stipulations in res pect of the disposal of the device at the

end of its lifecycle

Battery Safety Reminders

Please dispose of batteries resp onsibly; always ob serve local, state, and federal regulations

with regard to battery disposal.

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types or old and ne w batteri es. Always install new batteries of the same

type.

Specifications

General Specifications

DCLxirtamtoDyalpsiD

Maximum Load 1000 ohms @ 24mA

Meter Power 6 AA batteries or AC adaptor

Auto Power OFF Meter automatically powers off af ter 10 minutes of inactivity

Current output capability 24mADC at 1000 ohms

Voltage input impedance 10kohms minimum

Operating Temperature 5ºC to 40ºC (41ºF to 104ºF)

Storage Temperature -20ºC to 60ºC (- 4ºF to 140ºF)

Operating Humidity Max 80% u p to 31ºC (87ºF ) decreasing linearly to 50% at 40ºC

(104ºF)

Storage Humidity <80%

Operating Altitude 7000ft (2000meters) maximum

Dimensions 159 x 80 x 44 mm (6.3 x 3.2 x 1.7")

seirettabtuohtiw).zo3.8(g432thgieW

Range Specifications

Mode Function Range (Resolution) Accuracy (% of reading)

Current 0 to 50mA (0.01mA)

Percent (%) -25% to +230% (0.1%)

0 to 1999mV (1mV)

Measure

Voltage

(autorange)

2 to 20V (0.01V)

Current 0 to 24mA (0.01mA)

Percent (%) -25% to +125% (0.1%)

0 to 2000mV (1mV)

DC Source

Voltage

0 to 20V (0.01V)

± (0.01% + 1 digit)

www.extech.com

more info for Extech PRC15

Phone: 01235 838 555

Email: cs@airconcern.co.uk

Web: www.airconcern.co.uk

Air Concern Ltd, Building 173 Curie Avenue Harwell Didcot, Oxfordshire

Autres manuels pour PRC15

Table des matières

Autres manuels Extech Instruments Équipement de test

Extech Instruments

Extech Instruments ET15 Manuel utilisateur

Extech Instruments

Extech Instruments ET28B Manuel utilisateur

Extech Instruments

Extech Instruments 380353 Manuel utilisateur

Extech Instruments

Extech Instruments 433201 Manuel utilisateur

Extech Instruments

Extech Instruments ET15 Manuel utilisateur

Extech Instruments

Extech Instruments 382357 Manuel utilisateur

Extech Instruments

Extech Instruments 382357-NIST Manuel utilisateur

Extech Instruments

Extech Instruments 380366 Manuel utilisateur

Extech Instruments

Extech Instruments CT80 Manuel utilisateur

Extech Instruments

Extech Instruments CB10 Manuel utilisateur

Extech Instruments

Extech Instruments 380375 Manuel utilisateur

Extech Instruments

Extech Instruments 412355A Manuel utilisateur

Extech Instruments

Extech Instruments ExStik CL200 Manuel utilisateur

Extech Instruments

Extech Instruments 380260 Manuel utilisateur

Extech Instruments

Extech Instruments CB10 Manuel utilisateur

Extech Instruments

Extech Instruments CB20 Manuel utilisateur

Extech Instruments

Extech Instruments PRC50 Manuel utilisateur

Extech Instruments

Extech Instruments IRC350 Manuel utilisateur

Extech Instruments

Extech Instruments VT10 Manuel utilisateur

Extech Instruments

Extech Instruments 380260 Manuel utilisateur

Extech Instruments

Extech Instruments ET30B Manuel utilisateur

Extech Instruments

Extech Instruments 480303 Manuel utilisateur

Extech Instruments

Extech Instruments ET26B Manuel utilisateur

Extech Instruments

Extech Instruments ET25 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur