Extech Instruments MS6100 Manuel utilisateur

User Manual

MS6000 Series

Digital Storage Oscilloscope

www.burntec.com

2 MS6000-EU-EN-V1.3 7/12

Chapter 1 – Contents

CHAPTER 1- CONTENTS........................................................................................2

1.1GENERAL SAFETY SUMMARY ...............................................................................5

1.2SAFETY TERMS AND SYMBOLS .............................................................................6

1.3TERMS ON PRODUCT ............................................................................................6

1.4SYMBOLS ON PRODUCT........................................................................................6

1.5PRODUCT AND BATTERY DISPOSAL ......................................................................7

CHAPTER 2- OVERVIEW ........................................................................................8

2.1BRIEF INTRODUCTION ON MS6000 SERIES ..........................................................8

CHAPTER 3- GETTING STARTED GUIDE...........................................................9

3.1INSTALLATION ......................................................................................................9

3.2FUNCTIONAL CHECK ............................................................................................9

3.3POWER ON THE OSCILLOSCOPE............................................................................9

3.4CONNECT THE PROBE TO THE OSCILLOSCOPE .......................................................9

3.5OBSERVING A WAVEFORM ...................................................................................10

3.6PROBE EXAMINATION.........................................................................................10

3.7SAFETY ..............................................................................................................10

3.8MANUAL PROBE COMPENSATION .......................................................................11

3.9PROBE ATTENUATION SETTING...........................................................................12

3.10SELF CALIBRATION ............................................................................................12

3.11MULTIFUNCTION CONTROL ................................................................................12

-MAIN FEATURES ...........................................................................................................13

3.12OSCILLOSCOPE SETUP ........................................................................................13

3.13TRIGGER ............................................................................................................13

3.14DATA ACQUISITION ............................................................................................15

3.15WAV E F O R M SCALING AND POSITIONING ............................................................16

3.16WAV E F O R M MEASUREMENT...............................................................................17

www.burntec.com

3 MS6000-EU-EN-V1.3 7/12

CHAPTER 4- BASIC OPERATION .......................................................................19

4.1DISPLAY AREA ...................................................................................................20

4.1.1XY Format ...............................................................................................22

4.2HORIZONTAL CONTROLS ....................................................................................23

4.2.1Scan Mode Display (Roll Mode)...........................................................26

4.3VERTICAL CONTROLS.........................................................................................26

4.3.1Math FFT .................................................................................................29

4.3.1.1Setting Time-domain Waveform ....................................................................... 29

4.3.1.2Displaying FFT Spectrum................................................................................. 31

4.3.1.3Selecting FFT Window ..................................................................................... 32

4.3.1.4FFT Aliasing ..................................................................................................... 34

4.3.1.5Eliminating Aliases........................................................................................... 34

4.3.1.6Magnifying and Positioning FFT Spectrum................................................. 35

4.3.1.7Using Cursors to Measure FFT Spectrum......................................................... 35

4.4TRIGGER CONTROLS ..........................................................................................37

4.5MENU AND OPTION BUTTONS ............................................................................46

4.5.1SAVE/RECALL .......................................................................................46

4.5.2MEASURE...............................................................................................48

4.5.3CURSOR .................................................................................................50

4.5.4UTILITY....................................................................................................51

4.5.5DISPLAY..................................................................................................55

4.5.6ACQUIRE ................................................................................................56

4.5.7Fast Action Buttons ................................................................................58

4.5.8AUTOSET................................................................................................58

CHAPTER 5- MULTIMETER OPERATION..........................................................60

CHAPTER 6- TROUBLESHOOTING ...................................................................73

6.1PROBLEM SOLVING ............................................................................................73

CHAPTER 7- SPECIFICATIONS...........................................................................74

7.1TECHNICAL SPECIFICATIONS ..............................................................................74

www.burntec.com

4 MS6000-EU-EN-V1.3 7/12

CHAPTER 8- GENERAL CARE AND CLEANING.............................................87

8.1GENERAL CARE..................................................................................................87

8.2CLEANING ..........................................................................................................87

www.burntec.com

5 MS6000-EU-EN-V1.3 7/12

- Safety Tips

1.1 General Safety Summary

Read the following safety precautions to avoid injury and prevent damage to this product or any

products connected to it. To evade potential hazards, use this product only as specified.

Only qualified personnel should perform maintenance.

Avoid fire or personal injury.

Use suitable power cord. Use only the power cord specified for this product and certified for the

country of use.

Connect and disconnect properly. Connect a probe with the oscilloscope before it is connected to

measured circuits; disconnect the probe from the oscilloscope after it is disconnected from measured

circuits.

Ground the product. This product is grounded through the grounding conductor of the power cord. To

avoid electric shock, the grounding conductor must be connected to earth ground. Before making

connections to the input or output terminals of the product, ensure that the product is properly grounded.

Connect the probe in a right way. The probe ground lead is at ground potential. Do not connect the

ground lead to an elevated voltage.

Check all terminal ratings. To avoid fire or shock hazard, check all ratings and markings on the product.

Refer to the product manual for detailed information about ratings before making connections to the

product.

Do not operate without covers. Do not operate this product with covers or panels removed.

Avoid exposed circuitry. Do not touch exposed connections and components when power is present.

Do not operate with suspected failures. If damage to this product is suspected, have it inspected by

qualified service personnel.

Assure good ventilation.

Do not operate in wet/damp environments.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

www.burntec.com

6 MS6000-EU-EN-V1.3 7/12

1.2 Safety Terms and Symbols

The following terms may appear in this manual:

WARNING Warning statements point out conditions or practices that could result in injury or

loss of life.

CAUTION Caution statements identify conditions or practices that could result in damage to

this product or other property.

1.3 Terms on Product

The following terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as the marking is read.

WARNING indicates an injury hazard not immediately accessible as the marking is read.

CAUTION indicates a possible hazard to this product or other property.

1.4 Symbols on Product

The following symbols may appear on the product:

Mains

Disconnected

OFF (Power)

Mains

Connected

ON (Power)

High Voltage

Protective

Ground

(Earth)

Terminal

Measurement

Ground

Terminal

CAUTION

Refer to Manual

Measurement

Input Terminal

www.burntec.com

7 MS6000-EU-EN-V1.3 7/12

1.5 Product and Battery Disposal

Battery Recycling and Disposal

You, as the end user, are legally bound (EU Battery ordinance) to return all used batteries,

disposal in the household garbage is prohibited! You can hand over your used batteries /

accumulators at collection points in your community or wherever batteries / accumulators

are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the end of its

lifecycle

www.burntec.com

8 MS6000-EU-EN-V1.3 7/12

Chapter 2 - Overview

2.1 Brief Introduction on MS6000 Series

Model Channels Bandwidth Sample Rate LCD

MS6060 2 60MHz 1GS/s 5.6 inch color

MS6100 2 100MHz 1GS/s 5.6 inch color

MS6200 2 200MHz 1GS/s 5.6 inch color

Table 2-1 Model List of MS6000 Series

MS6000 Series oscilloscopes bandwidths range from 60MHz to 200MHz, and provide real-time

and equivalent sample rates respectively up to 1GSa/s and 25GSa/s. In addition, they have maximum

1MB memory depth for better observation of the waveform details, and 5.6 inch color TFT LCD as well

as WINDOWS-style interfaces and menus for easy operation.

Additionally, the generous menu information and the easy-to-operate buttons maximize the

information available for each measurement; the multifunctional and powerful shortcut keys save time

and maximize efficiency; the Autoset (AUTO) function allows the user to detect sine and square waves

automatically.

www.burntec.com

9 MS6000-EU-EN-V1.3 7/12

Chapter 3 - Getting Started Guide

3.1 Installation

To keep proper ventilation of the oscilloscope in operation, leave a space of more than 5 cm (2”) from the

top and the two sides of the product.

3.2 Functional Check

Follow the steps below to perform a quick functional check to your oscilloscope.

3.3 Power ON the oscilloscope

Press the ON/OFF button. The start-up sequence will take up to 15 seconds to complete.

NOTE: The AC Charger is intended for battery charging only.

Use of charger during measurements is not recommended.

The default probe parameter

3.4 Connect the Probe to the oscilloscope

Set the switch on the probe to 10X and connect the probe to the Channel 1 BNC on the oscilloscope.

Connect the probe tip to the 1 KHz Probe Compensation connector and the reference lead to the

Ground connector. The CH1 default Probe option attenuation setting is 1X, change this to 10X.

Channel 1 Probe Connection

Connect Probe tip to 1-KHz

signal when compensating

Ground connection for reference lead

when compensating

www.burntec.com

10 MS6000-EU-EN-V1.3 7/12

3.5 Observing a waveform

Press the AUTO button and a 1 KHz square wave of approx. 5V peak-to-peak will appear in the display.

Press the CH1 button and remove Channel 1. Move the Probe to the CH2 BNC, push the CH2 button

and repeat these steps to observe the test signal on Channel 2.

3.6 Probe Examination

3.7 Safety

When using the probe, keep fingers behind the guard on the probe body to avoid electric shock. Do not

touch metallic portions of the probe head while it is connected to a voltage source. Connect the probe to

the oscilloscope and connect the ground terminal to ground before starting any measurements.

www.burntec.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extech Instruments Équipement de test

Extech Instruments

Extech Instruments GX930 Manuel utilisateur

Extech Instruments

Extech Instruments 380260 Manuel utilisateur

Extech Instruments

Extech Instruments BR90 Manuel utilisateur

Extech Instruments

Extech Instruments ExStik CL200 Manuel utilisateur

Extech Instruments

Extech Instruments VT30 Manuel utilisateur

Extech Instruments

Extech Instruments TK32 Manuel utilisateur

Extech Instruments

Extech Instruments 380353 Manuel utilisateur

Extech Instruments

Extech Instruments RT30 Manuel utilisateur

Extech Instruments

Extech Instruments VT10 Manuel utilisateur

Extech Instruments

Extech Instruments 480400 Manuel utilisateur

Extech Instruments

Extech Instruments TK36 Manuel utilisateur

Extech Instruments

Extech Instruments HDV700 Manuel utilisateur

Extech Instruments

Extech Instruments MS420 Manuel utilisateur

Extech Instruments

Extech Instruments 380366 Manuel utilisateur

Extech Instruments

Extech Instruments ET40 Manuel utilisateur

Extech Instruments

Extech Instruments MG320 Manuel utilisateur

Extech Instruments

Extech Instruments CB10 Manuel utilisateur

Extech Instruments

Extech Instruments 407744 Manuel utilisateur

Extech Instruments

Extech Instruments 480303 Manuel utilisateur

Extech Instruments

Extech Instruments ET60 Manuel utilisateur

Extech Instruments

Extech Instruments 412300 Manuel utilisateur

Extech Instruments

Extech Instruments HDV600 Manuel utilisateur

Extech Instruments

Extech Instruments BR50 Manuel utilisateur

Extech Instruments

Extech Instruments 380363 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur