Extech Instruments FHT200 Manuel utilisateur
User’s Guide
Fruit Hardness Tester
Model
FHT200
FHT200-EU-EN-V1.2 5/11
2
Introduction
Congratulations on your purchase of Extech’s Fruit Hardness Tester Model FHT200. The tester is
used to measure the hardness (ripeness) of fruits such as apples, pears, strawberries and grapes.
Users include fruit science research departments, fruit producers, fruit farms and agricultural
colleges and universities to improve the fruit quality, harvest, storage, and product transportations.
The tester helps to judge the fruit's degree of maturity. This professional meter, with proper care, will
provide years of safe reliable service.
Features
•Maximum capacity: 20.00Kg / 44.10lb / 196.10 Newton.
•Units: Kg/lb/Newton
•Includes a high precision load cell sensor
•Digital display with Peak hold function for easy measurement
•Tension or Compression
•Positive/ Reverse display
•Large backlight LCD display
•RS-232/USB computer interface
•Complete set with hard carrying case and 4 tips (3 mm, 6 mm, 8 mm, 11 mm)
•Optional USB cable and data acquisition software
•Peak hold (Max. load) can be held in display during the measurement
•Zero button can operate both for normal mode and "peak hold" mode
•Full capacity zero (tare) control capability
•Fast/Slow response time
•Low power consumption for long battery life
•Microprocessor circuit & exclusive load cell transducer
•Overload protection
•DC 9V power adapter input socket
FHT200-EU-EN-V1.2 5/11
3
Meter Description
1. Measurement Tip mounting screw
2. Fast selection indicator
3. LCD display
4. FAST/SLOW button
5. LCD Reverse Display button
6. Kg/Newton/LB unit switch
7. OFF/ON/PEAK HOLD switch
8. RS-232 output terminal
9. LCD Back Light button
10. Zero button
11. Battery Compartment (rear)
12. DC 9V Power Adapter input socket
13. 11mm Tip
14. 8mm Tip
15. 6mm Tip
16. 3mm Tip
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FHT200-EU-EN-V1.2 5/11
4
Operation
Preparation for Measurement
1. Select and install the tip most suitable for the fruit to be tested.
2. Slide the Power switch to the “I” position to turn the meter on.
3. If the meter display remains blank or the “Lo” low battery indicator
appears in the display, replace the batteries.
4. Fruit hardness tests utilize the compression function of the meter.
The Tension (pull) function is displayed with a “-“ symbol and is not
normally used for fruit hardness tests.
5. For the most repeatable results, place the fruit against a firm surface
when making measurements.
6. Press the measurement tip perpendicular against the fruit surface.
Do not measure at an angle.
Tip Selection
There are four diameter tips: 3mm, 6mm, 8mm and 11mm. Which tip should be used is based on
the user’s experience, type of fruit or vegetable, location the fruit was grown and ripeness of the
fruit. Always log tip used with measurement results to establish optimum testing results and insure
repeatability of the measurement.
General recommendations are:
3mm Small fruits, berries
6mm Hard fruits, grapes
8mm Firm fruits, pears
11mm Apples
Fruit Preparation
For most measurements, skin removal is recommended.
FHT200-EU-EN-V1.2 5/11
5
Peak Measurement
The Peak mode is the most commonly used mode for fruit harness testing.
1. Install a tip.
2. Slide the POWER switch to the “Peak H” position.
3. Select units of measure (grams/kilograms, ounces/pounds, or newtons) using the units select
switch.
4. Press the ZERO button to zero the display.
5. Select FAST or SLOW response. FAST is the preferred speed for fruit harness testing.
6. Properly align the tip and the fruit and then slowly increase the applied pressure against the
fruit..
7. When the tip breaks the surface, the force will release and the peak value, which is the highest
reading encountered, will remain ‘held” in the display.
8. Press the ZERO button to clear the display for the next measurement.
Normal Measurement Mode
1. Install a tip.
2. Slide the POWER switch to the “I” position.
3. Select units of measure (grams/kilograms, ounces/pounds, or newtons) using the units select
switch.
4. Press the ZERO button to zero the display.
5. Select FAST or SLOW response. FAST is the preferred speed for fruit harness testing.
6. Properly align the tip and the fruit and then slowly increase the applied pressure against the
fruit.
7. Observe the display to monitor the applied force.
LCD Backlight
The backlight feature provides display illumination when the meter is used at night or in dimly lighted
areas. Press and hold ( > 2 seconds ) the button until LCD backlight is turns ON. The backlight
will automatically turn off after approximately 6 seconds
Reverse Display
The Reverse Display feature flips the display upside-down to permit easy reading of the results
regardless of the direction the meter is held during measurement.
Fast-Slow
The Fast-Slow feature selects the meter’s response time. Slow response will average the reading
over a longer time period and Fast response will display more rapid changes.
“FAST” appears in the display when it is selected, no display indication appears for slow.
RS232 PC/USB Interface
Optional software is available to log, graph and save measured data.
FHT200-EU-EN-V1.2 5/11
6
Maintenance
Battery Replacement
The low battery indication appears on the LCD as "Lo". Replace the batteries when this symbol
appears.
1. Remove the two screws securing the battery compartment cover.
2. Lift off the battery cover.
3. Replace with 6x 1.5V AA (UM-3) batteries. Observe polarity.
4. Replace compartment cover and screws.
All EU users are legally bound by the battery ordinance to return all used batteries to
collection points in your community or wherever batteries / accumulators are sold!
Disposal in the household garbage is prohibited!
Specifications
Display 5 digits LCD with backlight.
Transducer Load cell.
Units Kg/Newton/LB.
Measure Capacity 20.00Kg / 44.10LB / 196.10 Newton.
Resolution 0.01Kg / 0.01LB / 0.05 Newton.
Min. Display 0.02Kg / 0.07LB / 0.3 Newton,
Accuracy ± (0.5 % + 2 digits), within 23± 5°C, and @ 10 Kg & 20 Kg.
Update time Fast: Approx. 0.2 second, Slow: Approx. 0.6 second.
Over range Indicator " - - - - " is displayed
Data output RS-232 serial computer interface.
Overload Capacity Max. 30kg.
Full Scale Deflection Approx. 0.4mm max.
Data output RS-232 serial computer interface
Mounting Holes Located on rear (thread size: M5 x 0.8mm ISO); mounting screws
included
Power Supply 6 x 1.5 V AA (UM-3) batteries or 9VDCadapter (not included).
Power Consumption Approx. DC 28 mA
Operating Temperature 0°C to 50°C (32°F to 122°F).
Operating Humidity Less than 80% RH.
Dimension 215 x 90 x 45 mm ( 8.5 x 3.5 x 1.8 inch ).
Weight 650g (1.43lb)/with batteries.
Copyright ©2011 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form
www.extech.com
Table des matières
Autres manuels Extech Instruments Instrument de mesure
Extech Instruments
Extech Instruments MA640 Manuel utilisateur
Extech Instruments
Extech Instruments MA220 Manuel utilisateur
Extech Instruments
Extech Instruments AN500 Manuel utilisateur
Extech Instruments
Extech Instruments MO57 Manuel utilisateur
Extech Instruments
Extech Instruments 380941 Manuel utilisateur
Extech Instruments
Extech Instruments Oyster Series Manuel utilisateur
Extech Instruments
Extech Instruments MO230 Manuel utilisateur
Extech Instruments
Extech Instruments PH220 Manuel utilisateur
Extech Instruments
Extech Instruments SDL350-NIST Manuel utilisateur
Extech Instruments
Extech Instruments MZ13604 Manuel utilisateur
Extech Instruments
Extech Instruments 480823 Manuel utilisateur
Extech Instruments
Extech Instruments MO210 Manuel utilisateur
Extech Instruments
Extech Instruments HDV7C-55-HD-1 Manuel utilisateur
Extech Instruments
Extech Instruments ExStik RE300 Manuel utilisateur
Extech Instruments
Extech Instruments 382152 Manuel utilisateur
Extech Instruments
Extech Instruments MO55W Manuel utilisateur
Extech Instruments
Extech Instruments 407735 Manuel utilisateur
Extech Instruments
Extech Instruments DT300 Manuel utilisateur
Extech Instruments
Extech Instruments MO220 Manuel utilisateur
Extech Instruments
Extech Instruments LT510 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur