Extech Instruments ExStik RE300 Manuel utilisateur

User Guide

ExStikTM Model RE300

Waterproof ORP Pen

Patent Pending

ExStikTM RE300-EU_ENG V2.2 02/08

ExStikTM Description

Front Panel Controls

1. Battery compartment cap

2. LCD Display

3. MODE button

4. CAL button (unused on RE300)

5. ON/OFF button

6. Electrode collar

7. Electrode

(Electrode cap is not shown)

Display Description

1. Bargraph

2. Units

3. Scale

4. Reading

5. Data Hold

6. Low Battery

CAUTIONS

•This device is not a toy and must not reach children’s hands. It contains hazardous

objects as well as small parts that the children could swallow. In case a child

swallows any of them, please contact a physician immediately

•Do not leave batteries and packing material lying around unattended; they can be

dangerous for children if they use them as toys

•In case the device is going to be unused for an extended period of time, remove the

batteries to prevent them from training

•Expired or damaged batteries can cause cauterization on contact with the skin.

Always, therefore, use suitable hand gloves in such cases

•See that the batteries are not short-circuited. Do not throw batteries into the fire.

ExStikTM RE300-EU_ENG V2.2 02/08

Operation

Getting Started

Battery Activation: An insulating tab is located in the battery compartment and prevents

battery drain during storage. It must be removed before use.

White KCL crystals may be present in the cap. These crystals will dissolve in the soak or

they can be simply rinsed with tap water

When the RE300 is turned on, it enters the Automatic Calibration mode. ‘SELF’ and ‘CAL’

will appear on the LCD while calibration is in progress. After the calibration is complete,

‘SELF’ and ‘CAL’ will extinguish and both the main display and bargraph will read ORP in

mV units. The bargraph reads 0mV (far left), 500mV (center), and 1000mV (far right).

ORP Testing

1. Remove cap from the electrode and press the ON/OFF button to switch the RE300

on.

2. Dip the electrode1/2” to 1” into the test solution. Stir once and let the reading stabilize

for 1 to 3 minutes.

3. Note the ORP or press MODE to freeze the reading The HOLD display icon will

appear along with the held reading. The held reading will be stored in the next 15-

reading storage location (see below). Press the MODE key to return to normal

operation.

4. Press the ON/OFF button to turn the RE300 off. If you do not press a button for 10

minutes the RE300 shuts off automatically.

Data Hold

Press the MODE button to freeze the current reading. The HOLD display icon will appear

along with the held reading. The held reading will be stored in the next 15-reading storage

location (see below). Press the MODE key to return to normal operation.

15-Reading Measurement Storage

1. Press the MODE button to store a reading. The LCD will briefly display the memory

location number and then the value stored (Data Hold will activate).

2. Press MODE again to return to normal

operation. Repeat step 1 above to store

the next reading and so on.

3. If an attempt is made to store more than

15 readings, the stored readings (starting

with the first reading) will be overwritten.

Recalling Stored Readings

Note: First ensure that the HOLD symbol is not displayed. If it is, exit the HOLD function by

pressing the MODE button.

1. Press the CAL button once and then press the MODE button immediately after CAL is

displayed; the location number (1 through 15) will flash. If the CAL mode is

accidentally accessed (display flashing), press the CAL button again to exit.

2. The last stored reading taken will be displayed first. To advance through the stored

readings, press the MODE button. The location number is displayed first, followed by

the reading stored in that location.

3. To exit the storage mode, press the CAL button and the ExStikTM will return to normal

operation.

ExStikTM RE300-EU_ENG V2.2 02/08

Measurement and Display Considerations

•If the unit appears to be locked (display frozen). It is possible that the Data Hold mode

has been inadvertently accessed by pressing the MODE button. Simply press the

MODE button again or turn the meter off and restart if the display appears frozen.

•If the meter does latch up and no button presses revive it, remove the batteries and

restart.

•Note that if the batteries are removed, any stored readings will be discarded. Factory

calibration data for all models will be retained, however.

Replacing Electrodes

To preserve Electrode life keep the sponge in the protective cap soaked

with tap water. When not in use (store vertically).

DO NOT USE DE-IONIZED WATER.

1. To remove an electrode, unscrew and completely remove the electrode collar (turn

the collar counter-clockwise to remove).

2. Gently rock the electrode from side to side, pulling it downwards, until it disconnects

from the meter.

3. To attach an electrode, carefully plug the electrode into the meter socket (note that

the electrode connector is keyed, ensuring proper connection).

4. Tighten the electrode collar firmly enough to make a good seal (a rubber gasket seals

the electrode with the meter).

ExStikTM RE300-EU_ENG V2.2 02/08

Battery Replacement

1. Twist off the battery compartment cap

2. Replace the four (4) CR2032 batteries

observing polarity.

3. Replace the battery compartment cap

You, as the end user, are legally bound (Battery ordinance) to return all used

batteries and accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators, gratuitously, at the

collection points for our branches in your community or wherever batteries /

accumulators are sold!

Disposal

Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Specifications

Display Multifunction LCD with Bargraph

Operating conditions 0 to 50oC (32 to 122oF) / < 80% RH

ORP Range / Accuracy ± 999mV / ± 4mV

Measurement storage 15 tagged (numbered) readings

Power Four (4) CR2032 button batteries

Low battery indication ‘BAT’ appears on the LCD

Auto power off After 10 minutes of inactivity

Dimensions 35.6x172.7x40.6mm (1.4x6.8x1.6”); 110g (3.85oz)

www.extech.com

Table des matières

Autres manuels Extech Instruments Instrument de mesure

Extech Instruments

Extech Instruments MO55W Manuel utilisateur

Extech Instruments

Extech Instruments CO250 Manuel utilisateur

Extech Instruments

Extech Instruments 42265 Manuel utilisateur

Extech Instruments

Extech Instruments SDL800 Manuel utilisateur

Extech Instruments

Extech Instruments 380580 Manuel utilisateur

Extech Instruments

Extech Instruments RH390-NIST Manuel utilisateur

Extech Instruments

Extech Instruments DT500 Manuel utilisateur

Extech Instruments

Extech Instruments ExStik DO600 Manuel utilisateur

Extech Instruments

Extech Instruments CO210 Manuel utilisateur

Extech Instruments

Extech Instruments RH300 Manuel utilisateur

Extech Instruments

Extech Instruments VB400 Manuel utilisateur

Extech Instruments

Extech Instruments HD750 Manuel utilisateur

Extech Instruments

Extech Instruments VB400 Manuel utilisateur

Extech Instruments

Extech Instruments 407113 Manuel utilisateur

Extech Instruments

Extech Instruments EC210 Manuel utilisateur

Extech Instruments

Extech Instruments MO270 Manuel utilisateur

Extech Instruments

Extech Instruments AUT10 Manuel utilisateur

Extech Instruments

Extech Instruments DT300 Manuel utilisateur

Extech Instruments

Extech Instruments RH300 Manuel utilisateur

Extech Instruments

Extech Instruments MA410T Manuel utilisateur

Extech Instruments

Extech Instruments GRT300 Manuel utilisateur

Extech Instruments

Extech Instruments SDL470 Manuel utilisateur

Extech Instruments

Extech Instruments CO250 Manuel utilisateur

Extech Instruments

Extech Instruments 407768 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur