Extech Instruments 401025 Manuel utilisateur
USER MANUAL
Model 401025
Digital Light Meter
Additional User Manual Translations available at
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
2
Introduction
Congratulations on your purchase of the Extech Digital Light Meter. This device is shipped fully tested
and calibrated and, with proper use, will provide years of reliable service. Please visit our website
check for the latest version of this User Guide, Product Updates, and Customer
Support.
Meter Description
1. LCD Display
2. Data Hold Switch
3. Power Off/Range Switch
4. Analog Output Terminal
5. Battery Compartment (rear)
6. LUX/Fc Switch & Response Switch
7. Light Sensor
8. Zero adjust
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
3
Lux
Operation
1. Select Units (Lux or Ft-candle) and the Response Time (Fast/Slow) using the slide switch. Typical
selection is Slow and Fc using the gray lettering.
2. Select the maximum range using the Range Switch.
3. Hold the Light Sensor so that the sensor faces the light source to be measured.
4. The display will indicate measured values. Use a range display multiplier if on the Lux 20,000 and
50,000 ranges or on the Fc 5000 range (see notes below).
5. To hold (freeze) a measurement, slide the Data Hold Switch to the Hold position. The reading will
freeze in the display until the Data Hold Switch is released.
Note 1: An Over Range indication is a display of "1__ ". If this occurs, switch to a higher range.
Note 2: For measurements made on the Fc 5000 range, the displayed reading must be multiplied by
10.
Note 3: For measurements made on the Lux 20000 or 50000 ranges the displayed reading must be
multiplied by 10 and 100 respectively.
Note 4: The meter will indicate values above the maximum ranges. The accuracy of these
measurements is unknown.
Range Display Multipliers
Range Units Multiplier
200 Fc Direct reading
2000 Fc & Lux Direct reading
5000 Fc Reading x10
20,000 Lux Reading x10
50,000 Lux Reading x100
Example: If a measurement on the 5000 Fc range displays 350 the actual measured value is:
350 x 10 = 3500 Fc.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
4
Selecting a Measurement Range
The meter has three measurement ranges for each unit of measure (0-200, 0-2000, and 0-5000 Fc)
and (0-2000, 0-20000, and 0-50000) Lux). The proper range selection will produce the most accurate
reading. Always select the range that produces the maximum number of digits without exceeding the
maximum count for that particular range. For example, a reading of 1456 Fc should be read on the 0
- 2000 range, not the 0-5000 range.
Zero procedure
The meter zero (display with no light input) may change with time. Occasional checking and
adjustment may be required.
1. Completely cover the sensor to block out any light.
2. Set the range switch to the lowest Lux or Fc range.
3. Using a small screwdriver, adjust the Zero control for a zero display. The last digit may
change slightly. This is normal and does not affect the accuracy of the meter.
Analog Output
The analog output jacks on the front panel produce a 0.1mV DC per digit signal that can be used for
recording or datalogging purposes.
Lighting Type Correction Factors
The 401025 light meter is calibrated under a precise Standard tungsten light source of 2856OK. If the
meter is to be used under a different type of light the correction factor of from the table below should
be applied to the readings obtained.
Mercury Lamp x1.14
Fluorescent Lamp X0.92 to 1.12
Daylight x1.00
Sodium x1.22
Metal Halide x1.00
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
5
Replacing the Battery
When the left corner of the LCD display shows LO BAT the battery output is below the design limit and
the battery needs to be replaced. However, reliable measurement can still be taken for several hours
before the tester becomes inaccurate or switches off.
1. Open the Battery Cover at the back of the tester and remove the old battery.
2. Replace with a new 9V battery and install the cover securely.
Never dispose of used batteries or rechargeable batteries in household waste.
As consumers, users are legally required to take used batteries to appropriate
collection sites, the retail store where the batteries were purchased, or wherever
batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-of-
life devices to a designated collection point for the disposal of electrical and electronic equipment.
Specifications
General Specifications
Display 13mm (0.5") LCD (Liquid Crystal Display)
Measurement types Lux, Ft-candles (Fc)
Ranges
(see range table
below)
Lux: 0 to 50,000 Lux in 3 ranges
Foot-candles: 0-5,000 Fc in 3 ranges
Sensor Exclusive photo diode & color correction filter, spectrum
designed to meet C. I. E.
Zero Adjust Manual adjustment
Sampling Time Approx. 0.4 seconds
Response Time Fast: 0.4 seconds; Slow: 2 seconds
Over input indication Indication of "1__"
Analog Output 0.1 mV/1 digit (maximum output: 200mV)
Operating Temperature 0OC to 50OC (32OF to 122OF)
Operating Humidity Less than 80% RH
Power Supply 9V DC battery
Power Current Approx. 2 mA DC
Weight 220 g (0.52 lbs.)
Dimensions Main instrument: 163 x 70 x 30 mm (6.4 x 2.8 x
Sensor Probe: 85 x 55 x 12 mm (3.2 x 2.2 x
Optional Accessories Vinyl pouch carrying case (Part Number 409996)
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
6
Range Specifications
Lux
Range In-range Display Resolution Accuracy (FS)
2,000 Lux 0-1,999 Lux 1 Lux ± (5% + 2digits)
20,000 Lux 2,000-19,990 Lux 10 Lux ± (5 % + 2digits)
50,000 Lux 20,000-50,000 Lux 100 Lux ±(5 % + 2digits)
Foot-candle (Fc)
Range In-range Display Resolution Accuracy (FS)
200 Fc 0-199.9 Fc 0.1 Fc ± (5% + 2digits)
2,000 Fc 200-1,999 Fc 1 Fc ± (5% + 2digits)
5,000 Fc 2,000-5,000 Fc 10 Fc ± (5% + 2digits)
Frequency Spectrum
300 400 500 600 700 800
1
0.8
0.6
0.4
0.2
0
Wavelength (nm)
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
401025-en-GB_v2.9 5/18
7
Appendix A - Typical Light Levels
Lux Foot
Candles
Lux Foot
Candles
Factories
Home
20-75 2-7 Emergency Stairs,
Warehouse
100-150 10-15 Washing
75-150 7-15 Exit/Entrance Passages 150-200 15-20 Recreational
Activities
150-300 15-30 Packing Work 200-300 20-30 Drawing Room,
Table
300-750 30-75 Visual Work: Production
Line
300-500 30-50 Makeup
750-1,500 75-150 Typesetting: Inspection
Work
500-1,500 50-150 Reading, Study
1,500-
3,000
150-300 Electronic Assembly,
Drafting
1,000-
2,000
100-200 Sewing
Office
Restaurant
75-100 7-10 Indoor Emergency Stairs 75-150 7-15 Corridor Stairs
100-200 10-20 Corridor Stairs 150-300 15-30 Entrance, Wash
Room
200-750 20-75 Conference, Reception
Room
300-750 30-75 Cooking/Dining
Room
750-1,500 75-150 Clerical Work 750-1,500 75-150 Show Window
1,500-
2,000
150-2000 Typing, Drafting
Store
Hospital
75-150 7-15 Indoors 30-75 3-7 Emergency Stairs
150-200 15-20 Corridor/Stairs 75-100 7-10 Stairs
200-300 20-30 Reception 100-150 10-15 Sick Room,
Warehouse
300-500 30-50 Display Stand 150-200 15-20 Waiting Room
500-750 50-75 Elevator 200-750 20-75 Medical Exam Room
750-1,500 75-150 Show Window, Packing
Table
750-1,500 75-150 Operating Room
1,500-
3,000
150-300 Storefront, Show Window 5,000-
10,000
500-1000 Eye Inspection
Appendix B - Common Terms and Conversion Factors
Illuminance (Visible Flux Density) 1 lm/m2=1 lux (lx)
10-4 lm/cm2
10-4 phot (ph)
9.290 x 10-2 lm/ft2
9.290 x 10-2 foot-candles
Luminance (Visible Flux Density per Solid Angle) 1 lm/m2/sr = 1 candela/m2
Luminous Intensity (Visible Flux per Solid Angle) 1 lm/sr = 1 candella
Luminous Flux ( Visible Flux) 1 lumen (lm) = 1.464 x 10-3 watts @ 555 nm
Copyright ©2013-2018 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
ISO-9001 Certified
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Extech Instruments Instrument de mesure
Extech Instruments
Extech Instruments LT505 Manuel utilisateur
Extech Instruments
Extech Instruments VB400 Manuel utilisateur
Extech Instruments
Extech Instruments RPM10 Manuel utilisateur
Extech Instruments
Extech Instruments RH25 Manuel utilisateur
Extech Instruments
Extech Instruments SL250W Manuel utilisateur
Extech Instruments
Extech Instruments MO257 Manuel utilisateur
Extech Instruments
Extech Instruments ExStik FL700 Manuel utilisateur
Extech Instruments
Extech Instruments MO270 Manuel utilisateur
Extech Instruments
Extech Instruments UV505 Manuel utilisateur
Extech Instruments
Extech Instruments PH220A Manuel utilisateur
Extech Instruments
Extech Instruments MO290 Manuel utilisateur
Extech Instruments
Extech Instruments ExStik EC510 Manuel utilisateur
Extech Instruments
Extech Instruments 451104 Manuel utilisateur
Extech Instruments
Extech Instruments 475040 Manuel utilisateur
Extech Instruments
Extech Instruments PQ3450 Manuel utilisateur
Extech Instruments
Extech Instruments 451112 Manuel utilisateur
Extech Instruments
Extech Instruments 407412 Manuel utilisateur
Extech Instruments
Extech Instruments 380580 Manuel utilisateur
Extech Instruments
Extech Instruments 461920 Manuel utilisateur
Extech Instruments
Extech Instruments 45168CP Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur