EtherWAN EX42008 Series Manuel utilisateur

EX42008series HardenedEthernetSwitch www.etherwan.com

This quick start guide describes how to install and use the Hardened Ethernet Switch.

Capable of operating at temperature extremes of -40°C to +75°C, this is the Switch of

choice for harsh environments constrained by space.

The Terminal Block and Power Inputs

Physical Description

The Port Status LEDs

LED State Indication

Steady Power on.

Power 1, 2 (Green) Off Power off.

Steady Relay starts alarm.

Fault (Red) Off Relay non-alarm.

10/100TX or 100FX/BX Ports

Steady A valid network connection established.

Blinking Transmitting or receiving data.

Act stands forActivity.

Link/Act (Green) Off No link.

Power Input Assignment

＋12~48VDC

Power 1

－Power Ground

＋12~48VDC

Power 2

－Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 250VAC

DC Terminal Block Power Input: The DC Terminal Block power input can be used to

power up this Switch.

DIP Switch Settings

DIP No. On Off

1 Port 1 Alarm Enable. Port 1 Alarm Disable.

2 Port 2 Alarm Enable. Port 2 Alarm Disable.

3 Port 3 Alarm Enable. Port 3 Alarm Disable.

4 Port 4 Alarm Enable. Port 4 Alarm Disable.

5 Port 5 Alarm Enable. Port 5 Alarm Disable.

6 Port 6 Alarm Enable. Port 6 Alarm Disable.

7 Port 7 Alarm Enable. Port 7 Alarm Disable.

8 Port 8 Alarm Enable. Port 8 Alarm Disable.

W70G-EX42008Q1

EX42008series HardenedEthernetSwitch www.etherwan.com

2 W70G-EX42008Q1

The Ethernet Connectors

The 10/100Base-TX Connections

The following lists the pinouts of 10/100Base-TX ports.

Pin Regular Ports Uplink port

1 Output Transmit Data + Input Receive Data +

2 Output Transmit Data - Input Receive Data -

3 Input Receive Data + Output Transmit Data +

4 NC NC

5 NC NC

6 Input Receive Data - Output Transmit Data -

7 NC NC

8 NC NC

The 100Base-FX Connections

The fiber port pinouts

The Tx (transmit) port of device I is connected to the Rx

(receive) port of device II, and the Rx (receive) port of device I to

the Tx (transmit) port of device II.

The WDM 100Base-BX Connections

The fiber port pinouts

Only one optical fiber is required to transmit and receive data.

Functional Description

Complies with EN61000-6-2 & EN61000-6-4 EMC Generic standard immunity for

industrial environment.

Supports IEEE802.3az 10Base-Te only. 10Base-T is not supported. 10Base-Te is

fully interoperable with 10Base-T over 100m of class D (Category 5) or better

cabling as specified in ISO/IEC 11801:1995.

Supports 802.3az/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/Half-duplex.

Auto MDI/MDIX.

100Base-FX: Multi/Single mode SC or ST type. 100Base-BX: WDM Single

mode SC type.

Supports 1024 MAC addresses, 448K bits buffer memory.

Supports IEEE802.3az Energy Efficient Ethernet (EEE).

IEEE802.1Q VLAN Tag Based Priority, Class of Service.

Output Queue Schedule Mode: Weighted Round Robin (WRR) with 2 priority

queues.

Power Supply: Redundant 12~48VDC Terminal Block power inputs.

Power consumption: 2.47W Max.

Provides reverse polarity protection.

Supports normal close and normal open.

Operating temperature ranges from -40°C to 75°C (-40°F to 167°F).

Slim design with DIN-Rail mount installation.

Assembly, Startup, and Dismantling

Assembly: Place the device on the DIN rail from above using the slot. Push the

front of the device toward the mounting surface until it audibly snaps into place.

Startup: Connect the supply voltage to start up the device via the terminal block.

Dismantling: Pull out the lower edge and then remove the device from the DIN

rail.

Autres manuels pour EX42008 Series

Table des matières

Autres manuels EtherWAN Changer

EtherWAN

EtherWAN EX83304 Series Manuel utilisateur

EtherWAN

EtherWAN EX32908 series Manuel utilisateur

EtherWAN

EtherWAN EX42008 Series Manuel utilisateur

EtherWAN

EtherWAN EG97000 Series Manuel utilisateur

EtherWAN

EtherWAN EX26262F Series Manuel utilisateur

EtherWAN

EtherWAN EX41941 Manuel utilisateur

EtherWAN

EtherWAN EX89000 Manuel utilisateur

EtherWAN

EtherWAN EX46900A Series Manuel utilisateur

EtherWAN

EtherWAN EX27000 Series Manuel utilisateur

EtherWAN

EtherWAN EX94000 Manuel utilisateur

EtherWAN

EtherWAN EX77000 Series Manuel utilisateur

EtherWAN

EtherWAN EX17162A Manuel utilisateur

EtherWAN

EtherWAN EX87000 Series Manuel utilisateur

EtherWAN

EtherWAN EX42300 series Manuel utilisateur

EtherWAN

EtherWAN EX48000A Series Manuel utilisateur

EtherWAN

EtherWAN EX32008 Series Manuel utilisateur

EtherWAN

EtherWAN EX63000 Series Manuel utilisateur

EtherWAN

EtherWAN EX16908 Manuel utilisateur

EtherWAN

EtherWAN EX43000 series Manuel utilisateur

EtherWAN

EtherWAN EX32008 Series Manuel utilisateur

EtherWAN

EtherWAN EX78000R Manuel utilisateur

EtherWAN

EtherWAN EX77900 Series Manuel utilisateur

EtherWAN

EtherWAN EX45900 series Manuel utilisateur

EtherWAN

EtherWAN EX95000 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur