Esse-ti GSM500 M2M Manuel utilisateur
26/09/2017
User’s manual
Thanks for choosing
an Esse-ti product
This product has been especially designed for easy
operation. It has been manufactured with perfect
workmanship using suitable materials for long-lasting
performance.
All Esse-ti products are subjected to extensive reliability
and operational testing in our laboratories in order to
provide total guarantee for the user.
The User shall be responsible for defects arising from the use of the product. Esse-ti shall only be
responsible for defects according to and within the limitations set by the Presidential Decree dated
24/05/1988 no. 224 (fulfilling the EEC directive no. 85/374 on the harmonization of statutory and
administrative regulations of the Member States on the liability for damages arising from defective
products under art. 15 of Law no. 183 of 16 April 1987).
Esse-ti reserves the right to modify the product characteristics at any time without prior notice.
TABLE OF CONTENTS
GENERAL INSTALLATION INSTRUCTIONS .............................. 5
General Notes ................................................................................. 5
Making the installation ................................................................... 5
DESCRIPTION .................................................................................. 6
Features .................................................................................................... 6
LED .......................................................................................................... 7
INSTALLATION ............................................................................... 8
Inserting the SIM card ............................................................................. 9
Inserting the antenna ................................................................................ 9
Connections ............................................................................................ 10
Connection to the power supply ............................................................ 11
Turning the GSM500 M2M device on .................................................. 12
Device mounting operations .................................................................. 13
GSM500 M2M installation recommendations ...................................... 14
PROGRAMMING............................................................................ 15
Message format ...................................................................................... 15
Notification message format .................................................................. 16
SMS text setting ........................................................................... 17
Setting telephone number for notifications .................................. 17
Notification type setting ............................................................... 18
Setting telephone number for technological alerts ....................... 18
Battery check ............................................................................... 19
External power failure control ...................................................... 19
Relay command ........................................................................... 20
Setting the relay administrator telephone number ........................ 21
SIGNALS ......................................................................................... 22
LED .............................................................................................. 22
GSM signal indicator LED (GREEN) ................................................... 22
Device status indicator LED (RED) ...................................................... 22
Input status indicator LED (WHITE) .................................................... 23
Line status indicator LED (BLUE) ........................................................ 23
PROBLEM-DETECTION GUIDE .................................................. 24
EU DECLARATION OF CONFORMITY ...................................... 25
Page 5
GENERAL INSTALLATION
INSTRUCTIONS
GENERAL NOTES
Carefully read the notes contained in this section as they provide important
information on safe correct installation, use and maintenance of the product.
The product must be EXCLUSIVELY used for the purpose it was designed for.
Esse-ti shall not be responsible for damages arising from improper use.
The product has been designed in compliance with the regulations in force and
must be installed in systems that comply with the provisions of law.
Always disconnect power supply before performing internal or external operations
on the product (cleaning, maintenance, etc.).
Always refer to an authorized service centre for repair.
The device must be installed in a ventilated place, making sure that the ventilation
slots are never obstructed.
Do not install the product in environments with risk of explosion.
Make sure that the product has been installed as required.
Do not introduce objects, liquids or powders inside the product. Do not use sprays
inside the product.
Packing components (such as plastic bags, foam polystyrene, etc.) must be kept out
of the reach of children because potentially dangerous.
MAKING THE INSTALLATION
Internal telephone installations must be carried out by specialised personnel.
The installation and connection of telephone terminals to the telecommunications
network that do not comply with the regulations in force is not permitted.
Page 6
DESCRIPTION
GSM500 M2M
The GSM500 M2M allows to send an SMS or a CLI call (ring) to a
programmed telephone number when the specific input TEL is closed.
For correct operation, a GSM SIM card is required.
GSM500 M2M GC
The GSM500 M2M GC comes with built-in backup batteries and a relay
output which can be activated remotely via SMS or CLI call (ring).
Features
Remote programming via SMS
Closing input TEL signalling via SMS or CLI call (ring)
Battery check (model GC)
External power failure control (model GC)
SMS technological alerts (low-battery, dead battery, replaced battery,
external power failure/restore; model GC)
Relay activation via SMS or CLI call (model GC)
GSM signal indicator LED
Device status indicator LED
Input status indicator LED
Line status indicator LED
Quad Band GSM module
2 W transmission power
12 Vdc power supply input
230 Vac external adapter input
Input TEL (normally open)
Relay output (model GC)
External antenna (cable length = 2 m)
Back up battery (NiMH 800 mAh 7,2 V; model GC)
Page 7
External adapter (230 Vac 50 Hz input; 12 Vdc 500 mA output; CE
mark).
LED
The GSM500 M2M is equipped with 4 outer LEDs.
LEDs flashing is described at chapter “SIGNALS” (see page 22).
Green LED: GSM signal indicator LED
Red LED: Device status indicator LED
White LED: Input status indicator LED
Blue LED: Line status indicator LED
Page 8
INSTALLATION
Remove the cover by pressing the upper side.
A ANTENNA cable connector
B SIM CARD housing with front panel
C LED indicating signal strength (green), LED indicating device status (red),
LED indicating input status (white) and LED indicating line status (blue)
D 230 Vac external adapter input
E TEL terminal block (normally open)
F 12Vdc power supply terminal block
G Relay terminal block (model GC)
H Backup battery connector (model GC)
Page 9
Inserting the SIM card
Before inserting or replacing the SIM card, always make sure that the
device has been disconnected from the mains and that no electrostatic
discharge is present in order to avoid damaging it.
Take all necessary measures to avoid electrostatic discharge.
Shift the SIM card housing cover downward until it unblocks and
lift it.
Carefully slide the SIM card into its housing cover.
Lower the SIM card housing cover and shift it upward until it
blocks.
WARNING
The SIM card PIN must be DISABLED. If the PIN is
enabled, it must be disabled through a mobile phone.
Inserting the antenna
Screw the antenna cable in to the connector on the top of the
module.
WARNING
NEVER connect the GSM500 M2M without having
previously installed the antenna. The device may get
damaged.
WARNING
Do not install the product near other electric or
electronic devices that were not especially designed to
be used with it. They could be subjected to RF
interference from the module.
Page 10
Position the antenna with magnetic base so that any metal
surfaces do not block the signal.
Connections
Connect the TEL terminal to a voltage free contact of an external
device.
Connect the RL terminal (if present and if necessary) to an external
device.
Table des matières
Autres manuels Esse-ti Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
