ESAB Origo Mig C170 3ph Manuel utilisateur

Valid for serial no. 626-xxx-xxxx0463 344 001 GB 20120612

Origo™

Mig C170 3ph

Mig C200 3ph

Mig C250 3ph

Instruction manual

- 2 -

- 3 -

TOCe

Rights reserved to alter specifications without notice.

1 SAFETY 4...........................................................

2 INTRODUCTION 6...................................................

2.1 Equipment 6................................................................

3 TECHNICAL DATA 6.................................................

4 INSTALLATION 7....................................................

4.1 Location 7..................................................................

4.2 Assembly of components 8...................................................

4.3 Electrical installation 8.......................................................

4.4 Mains power supply 9........................................................

5 OPERATION 9.......................................................

5.1 Connection and control devices 10.............................................

5.2 Welding without gas 11.......................................................

5.3 Wire feed pressure 11........................................................

5.4 Replacing and inserting wire 11................................................

5.5 Overheating protection 12.....................................................

6 MAINTENANCE 12....................................................

6.1 Inspection and cleaning 12....................................................

7 FAULT TRACING 13..................................................

8 ORDERING OF SPARE PARTS 13......................................

DIAGRAM 14............................................................

ORDER NUMBER 18.....................................................

WEAR PARTS 19........................................................

ACCESSORIES 20.......................................................

- 4 -

ba46e

1 SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be ob

served in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equip

ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in

jury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding and cutting

2. The operator must ensure that:

Sno unauthorised person is stationed within the working area of the equipment when it is

started up.

Sno-one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

WARNING

Do not use the power source for thawing frozen pipes.

- 5 -

ba46e

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

SInstall and earth the unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION

Read and understand the instruction manual before

installing or operating.

CAUTION

This product is solely intended for arc welding.

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

- 6 -

ba46e

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

Mig C170 3ph, Mig C200 3ph and Mig C250 3ph are step controlled power

sources of a compact design, intended for welding with solid steel, stainless steel or

aluminium wire as well as tubular wire with or without shielding gas. It is possible to

weld with homogeneous wire/shielding gas and weld with gasless tubular wire by

switching the + and - connections on the switching terminal by the wire feed unit.

ESAB's accessories for the product can be found on page 20.

2.1 Equipment

The power source is supplied with:

SWelding gun

SReturn cable with return clamp

SShelf for gas cylinder

SInstruction manual

3 TECHNICAL DATA

Mig C170 3ph Mig C200 3ph Mig C250 3ph

Voltage 400-415V,

3∼50/60 Hz

400-415V,

3∼50/60 Hz

230/400-415V,

3∼50/60 Hz

Permissible load at

100% duty cycle 100A 120A 150A

60 % duty cycle 130A 150A 190A

35 % duty cycle 170A 200A 250A

Setting range (DC) 30-170A 30-200A 40-280A

Open circuit voltage 15.5-30.6V 16.0-31.8V 15.0-37.0V

Open circuit power 310W 210W 340W

Power factor at max load 0.97 0.97 0.97

Control voltage 42V, 50/60Hz 42V, 50/60Hz 42V, 50/60Hz

Wire feed speed 1.0-17m/min 1.0-17m/min 1.0-17m/min

Burnback time 0.02-0.25s 0.02-0.25s 0.02-0.25s

- 7 -

ba46e

Mig C250 3phMig C200 3phMig C170 3ph

Spot welding 0.2-2.5s 0.2-2,5s 0.2-2.5s

Welding gun connection EURO EURO EURO

Wire dimension range 0.6-0.8(Fe, SS)

1.0(Al)

0.8(FCW)

0.8-1.0(CuSi)

0.6-1.0(Fe, SS)

1.0(Al)

0.8-1.0(FCW)

0.8-1.0(CuSi)

0.6-1.2(Fe, SS)

1.0-1.2(Al)

0.8-1.2(FCW)

0.8-1.0(CuSi)

Max diameter / weight of

wire bobin

300mm/15kg 300mm/15kg 300mm/15kg

Dimensions lxwxh 860x420x730 860x420x730 860x420x730

Weight 63.5kg 72.5kg 82kg

Operating temperature -10 ÷+40°C -10 ÷+40°C -10 ÷+40°C

Transportation temperature -20 ÷+55°C -20 ÷+55°C -20 ÷+55°C

Enclosure class IP 23 IP 23 IP 23

Application classification

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40°C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

The installation must be carried out by a professional.

Note!

Connect the power source to the electricity mains with a network impedance of 0.268 (C250 3ph) ohm

or lower. If the network impedance is higher, there is a risk of flicker in the illuminators.

CAUTION

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

4.1 Location

Position the welding power source in such way that its cooling air inlets and outlets

are not obstructed.

- 8 -

ba46e

4.2 Assembly of components

WARNING

For packing and shipment of the machine the wheels are detached from the unit.

Before use attach the wheels according to instruction.

4.3 Electrical installation

C200 3ph

- 9 -

ba46e

4.4 Mains power supply

Check that the unit is connected to the correct mains power supply voltage, and that

it is protected by the correct fuse size. A protective earth connection must be made,

in accordance with regulations.

Rating plate with supply connection data

Recommended fuse sizes and minimum cable area

Mig C170 3ph Mig C200 3ph Mig C250 3ph

Voltage V 400-415V,

3∼50/60 Hz

400-415V,

3∼50/60 Hz

230 / 400-415V,

3∼50/60 Hz

Current A

at 100% duty cycle 4.0 5.3 12.1/7.0

at 60% duty cycle 6.1 6.8 17.6/10.2

at 35% duty cycle 8.9 10.1 25.3/14.6

Mains Cable area mm24 x 1.5 4 x 1.5 4 x 2.5 / 4 x 1.5

Fuse slow A 10 10 25/16

NB: The mains cable areas and fuse sizes shown above are in accordance with Swedish regulations.

They may not be applicable in other countries: make sure that the cable area and fuse sizes comply

with the relevant national regulations.

5 OPERATION

General safety regulations for handling the equipment can be found on

page 4. Read through before you start using the equipment!

WARNING

Rotating parts can cause injury, take great care.

WARNING

To prevent the reel from sliding off the hub: Lock the

reel in place by turning the red knob as shown on the

warning label attached next to the hub.

- 10 -

ba46e

WARNING

Secure the equipment - particularly if the

ground is uneven or sloping.

5.1 Connection and control devices

1Mains supply switch 7Connection for return cable (-), low inductance

2Indicator lamp, power ON/OFF 8Knob for spot welding - ON/OFF and time

setting

3Orange indicator lamp, overheating 9Knob for wire speed setting

4Welding voltage switch 10 Digital instrument - V/A (option,see page 20)

5EURO - connector for welding gun 11 Return cable with return clamp

6Connection for return cable (-), high

inductance

*Knob for burn-back time setting (located on

control board)

C250 3phC170 3ph

C200 3ph

Autres manuels pour Origo Mig C170 3ph

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ESAB Système de soudage

ESAB

ESAB OrigoArc 150 Manuel utilisateur

ESAB

ESAB Heliarc 283i AC/DC Manuel utilisateur

ESAB

ESAB MultiPower 460 Pulse Manuel utilisateur

ESAB

ESAB Caddy Tig 1500i VRD Manuel utilisateur

ESAB

ESAB Multimaster-260 Manuel du propriétaire

ESAB

ESAB A6TF F1 Manuel utilisateur

ESAB

ESAB Fabricator 181i Manuel utilisateur

ESAB

ESAB Origo Tig 3001i Manuel utilisateur

ESAB

ESAB Migmaster 275 Manuel utilisateur

ESAB

ESAB Origo M13 Feed 304 Manuel utilisateur

ESAB

ESAB Renegade ET 300i Manuel utilisateur

ESAB

ESAB POWERCUT-1250 Manuel utilisateur

ESAB

ESAB Origo Mig 320 Manuel utilisateur

ESAB

ESAB Origo Feed 30 Manuel utilisateur

ESAB

ESAB Caddy Tig 1500i TA34 Manuel utilisateur

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud Manuel utilisateur

ESAB

ESAB Caddy Arc 152i Manuel utilisateur

ESAB

ESAB MEK 4C Manuel utilisateur

ESAB

ESAB AristoFeed 30 4 Series Manuel utilisateur

ESAB

ESAB ARC 601i Manuel utilisateur

ESAB

ESAB Fabricator EM 401i Manuel utilisateur

ESAB

ESAB MECHTIG 160 Manuel utilisateur

ESAB

ESAB MultiMaster 160 Manuel utilisateur

ESAB

ESAB Aristo Mig C3000i Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur