ESAB TR-29 Manuel utilisateur

INSTRUCTIONS for

TR-29 TWO CYLINDER TRUCK KIT

Item No. 37924

for mounting:

353cv, 453cv, 653cvcc, MultiPower 460 and MultiPower 460 Pulse Power Sources

F15-592-B

March, 2003

This kit includes the following components:

1 — Assembled TR-29 Truck Body

1 — Cylinder Support

2 — Chain, 2/0 36" (not illustrated)

2 — Nuts 1/4" x 20 Lock

2 — Washer 1/4" Fender

4 — Screws 1/4"-20 1" Long

F15-592-B

Location of Screws

and U-Slots.

To mount Power Source on Truck, proceed as fol-

lows:

1. Carefully lift the power source off the floor with a

craneorhoistandremoveanyskidsfromthebase.

2. Lower the unit onto the truck base aligning the two

protruding screws on the rear bottom of the power

source (see photos above), with the U-slots pro-

vided in the truck base. The rear slots are located

just in front of the wheel guards. Note also that all

protruding bolt heads on the bottom of the power

sourcehaveaholedrilled in the truck floor for them

to pass through. When the Power Source is prop-

erly seated on the truck the weight of the unit is on

the floor of the truck not the side rails, and the front

floor of the truck will be flush with the lower front

panel of the Power Source.

Weight Bearing Area

(OPTIONAL)

- Install 1/4-20 Lock Nuts

on these screws once

assembled to the Truck Kit.

4. The cylinder support is installed by first removing

the four corresponding (assembly screws) on the

topfourcornersofthepower source.(SeeFigure4

onreverseside.) Setthesupportontopofthepower

sourceandinstallthelonger screwsprovided. (Note)

If top does not lay flush, loosen screws on handle

and retighten after assembly.

3. If bolting the power source to the base, 2 screws

should protrude through the TR-29 Floor from the

base of the power source. Attach one .250 flat

washer and one .250 lock nut to each screw.

This truck assembly is not intended to be hoisted

while attached in any way to a power source. If the

unit must be hoisted, the truck assembly must be

removed.

NEVERATTEMPT TOLIFTAPOWERSOURCE WITH

CYLINDER(S)ATTACHED!

5. Adjust cable strain relief bar to suitable height (see

Figure 3).

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Figure 1

Figure 2

6. To mount cylinders on completed assembly:

Slide at least the second link of each chain (678944)

into the center slot of the cylinder support.

Whenyou putthecylinders in place,pullthe chaintightly

aroundeach cylinder andslidea chain link intotheouter

slotof the cylinder support. Besure to pull the linkdown

firmly into each slot to secure the chain so that there is

littleslack of the chain about the cylinder. DO NOTjust

"loop" a link over the end of the support.

Cylinder support

assembly screws

Handle

Floor of Truck is flush

with lower panel of

Power Source.

Cable Strain Relief Bar

F15-592-B 03 / 2003

Figure 3 Figure 4

Assembly Screws on

Left Side not visible.

READ & UNDERSTAND THIS LABEL

PROTECT YOURSELF AND OTHERS

LIRE & COMPRENDE CETTE ETIQUETTE

VOUS PROTEGER ET LES AUTRES

Lifting eye to be used for lifting

power source ONLY.

Do NOT use when additional accessories

are attached to power source.

L’oeil d’ascenseur etre utilise

pour la source de pouver seulement.

ont attachesa la source de pouvoir.

PRUDENCE

P/N 99512240-C 3/22/02

Ce manuel convient aux modèles suivants

Autres manuels ESAB Accessoires de soudage

ESAB

ESAB LAF 1601M Manuel utilisateur

ESAB

ESAB Aristo U6 Manuel utilisateur

ESAB

ESAB PREST-O-LITE 02X93 Manuel utilisateur

ESAB

ESAB PSE-10 Manuel utilisateur

ESAB

ESAB TIGAID315 AC/DC Manuel utilisateur

ESAB

ESAB Eye-Tech 11 Mono Manuel utilisateur

ESAB

ESAB SDF-50 Manuel utilisateur

ESAB

ESAB SABRE V J28 Manuel utilisateur

ESAB

ESAB PT-31XL Manuel utilisateur

ESAB

ESAB A6 GMD Manuel utilisateur

ESAB

ESAB Warrior YardFeed 200 Manuel utilisateur

ESAB

ESAB Origo Feed 304 P4 Mode d’emploi

ESAB

ESAB Aristo U8 Manuel utilisateur

ESAB

ESAB CIGWELD 454342 Manuel utilisateur

ESAB

ESAB Eye-Tech 10-12 Select Manuel utilisateur

ESAB

ESAB PSF 250 Manuel utilisateur

ESAB

ESAB EFU 30 Manuel utilisateur

ESAB

ESAB SAVAGE A40 Manuel utilisateur

ESAB

ESAB EDB-15/30 Manuel utilisateur

ESAB

ESAB CIGWELD Arcmaster 649 Payday Manuel utilisateur

ESAB

ESAB PSF 260C Manuel utilisateur

ESAB

ESAB Eye-Tech 9-13 Manuel utilisateur

ESAB

ESAB PSF 315ME Manuel utilisateur

ESAB

ESAB SDF-250 Manuel utilisateur

Manuels Accessoires de soudage populaires d'autres marques

Lincoln Electric

Lincoln Electric LT-7 Tractor Manuel utilisateur

Weco

Weco Trolley R Manuel utilisateur

Cornwell Tools

Cornwell Tools MMWC1 Manuel utilisateur

Dohle

Dohle ExOn2A Manuel utilisateur

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manuel utilisateur

3M Speedglas 9100 Series Manuel utilisateur

Miller Electric

Miller Electric OM-842 Manuel utilisateur

Miller

Miller A-200 Series Manuel utilisateur

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manuel utilisateur

optrel

optrel lifeflip autopilot Manuel utilisateur

Miller

Miller MIGmatic M-25 Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manuel utilisateur

Abicor Binzel

Abicor Binzel xFUME PRO Manuel utilisateur

Sealey

Sealey SR20.V2 Manuel utilisateur

iWeld

iWeld NORED EYE Manuel utilisateur

Sthor

Sthor 74483 Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

Miller

Miller I-22 CE Manuel utilisateur