ESAB Eye-Tech 10-12 Select Manuel utilisateur

INSTRUCTIONS for

Eye-Tech 10-12 Select

Welding Helmet

P/N 15F20

ARC RAYS can burn eyes and skin. Wear safety

glasses and set proper filter shade. See ANSI/AWS

Z 9.1 for guide. Available from American Welding

Society, Miami, FL 33135.

The Eye-Tech 10-12 Select welding helmet is deliv-

ered fully assembled and ready for use. You only need

to adjust the headband and set the shade level. The

shade cartridge automatically darkens with arc igni-

tion.

Safety Precautions

lPitted or scratched plates reduce vision and protec-

tion. Replace worn or damaged parts immediately.

lAlways keep the external and internal protective plates

in place. Failure to do so will allow welding spatter to

pit the front surface of the shade cartridge. This can

reduce the built-in V and IR protection. (Also, the

weld spatter will void the warranty on the shade car-

tridge.)

lDo not attempt to open the shade cartridge.

lDo not use in cold weather (below 14° F).

lKeep solar cells clean. Clean with a damp not wet,

cloth dipped in soapy water. Dry with a soft, clean

cloth.

lDo not drop, strike, or bend helmet.

lDo not use abrasive cleaning agents.

lFumes and gases can be hazardous to your health.

Keep your head out of the fumes. Ventilate area or

use breathing devices, if necessary.

Keep helmet dry (especially the shade cartridge) and

do not place on hot surfaces.

Operation

lSet the slideswitch until it clicks to the shade level recom-

mended for your arc welding process. If you have doubts,

start with slideswitch in the 11-12 position. If you find that

the arc zone is too dark, then set slideswitch to the 1 -11

position.

lCheck to see if the front cover lens is inserted and front

lens frame is in place.

Troubleshooting

lUneven darkening

- Protective helmet is not on straight, causing the dis-

tance between your eyes and the shade cartridge to

vary. If necessary, decrease distance to shade cartridge.

lThe shade cartridge does not darken or it flickers

- Sensors are dirty; clean

- Front cover lens is dirty or damaged; clean or replace

- Welding current is too low

- Slideswitch not set properly (is in non-active center

position).

lSlow switching times

- Temperature is too low (should not be below 14° F)

- Lighting is insufficient

lPoor visibility

- Shade levels are set incorrectly

- Front or rear cover lens is dirty

- Room lighting is insufficient

lWelding helmet slips

- Headband is not properly adjusted (set too low)

If these faults cannot be corrected, do not use

helmet. Contact your distributor for assistance.

F-15-432

December, 1997

Be sure this information reaches the operator.

You can get extra copies through your supplier.

Specifications

Viewing Area: 3.86 x 1.50 (98 x 38mm)

Light transmittance: Ranges of sha e levels 10-11 & 11-12

Automatic sha e level function with selec-

tion of switch

Ultra-violet protection 15

Infra-re protection 14

Sha e level 4 in non-active state

Switch Time: From light to ark 0.1 millisecon s at room

temperature; from ark to light 0.2-0.3 sec-

on s

Operating Temp.: 14° F to 158° F (-10°C to +70°C)

Power Supply: Solar cells

Helmet Construction: High impact, synthetic material

Weight: 16.6 oz (470 grams)

Technical details are subject to change.

To replace rear cover

lens, place a small

screwdriver in groove

and pull out lens.

To adjust angle of

helmet, turn

Eccentric knob.

Loosen locking-nuts and

adjust distance from eyes.

Adjust both sides at the same

time. Make sure helmet

remains straight.

To remove front lens frame

grasp bottom and pull upward; to

replace, reverse process.

F-15-432 12/97 Printed in U.S.A.

Part

Spare Parts List Number

1 - Front Lens Frame ..................................... 15F 5

2 - Front Cover Lens (1 pcs) ........................ 15F 9

3 - Shade Cartridge ....................................... 15F21

4 - Rear Cover Lens (2 pcs) ........................ 15F1

5 - Eccentric Knob ......................................... 15F 8

6 - Head Band ............................................... 15F 3

7 - Sweat Band .............................................. 14F 4

8 - Helmet (without shade cartridge) .............. 15F 1

9 - Helmet Complete...................................... 15F2

ACCESSORIES

Part

Magnifying Lens Number

- Diopter + ........................................................15F11

- Diopter +1.5 .................................................... 15F12

- Diopter +2. .................................................... 15F13

- Diopter +2.5 .................................................... 15F14

After removing frames, insert front

cover lens into frame.

Use only P/N 15F0 front cover

lens. Replace front lens frame.

To replace shade cartridge, push

shade cartridge outwards from

the upper inside rim. To put back,

reverse process.

To adjust headband, set

upper adjusting strap as

low as possible.

The sweatband for the

forehead is removable

and washable.

Push in knob at back of

headband) and turn. It

will then click into

position.

Warranty

A two-year warranty from the date of manufacture is given against

defects arising from faulty workmanship or materials. No war-

ranty is given against defects arising from misuse, unauthorized

interference with parts or use of the appliance which was not

intended by the manufacturer.

Autres manuels pour Eye-Tech 10-12 Select

Autres manuels ESAB Accessoires de soudage

ESAB

ESAB Sentinel A50 Manuel utilisateur

ESAB

ESAB EFU 30 Manuel utilisateur

ESAB

ESAB A6 VEC Manuel utilisateur

ESAB

ESAB Eye-Tech 10-12 Select Manuel utilisateur

ESAB

ESAB Sentinel A60 Manuel utilisateur

ESAB

ESAB Arc Master ICE A6 S Manuel utilisateur

ESAB

ESAB Aristo W82 Manuel utilisateur

ESAB

ESAB Cigweld ProGuard Manuel utilisateur

ESAB

ESAB PSE-10 Manuel utilisateur

ESAB

ESAB PSF 250 Manuel utilisateur

ESAB

ESAB PEI Manuel utilisateur

ESAB

ESAB PSF 305 Manuel utilisateur

ESAB

ESAB SDF-250 Manuel utilisateur

ESAB

ESAB SDE-250 Manuel utilisateur

ESAB

ESAB SDF-250 Manuel utilisateur

ESAB

ESAB Eye-Tech 9-13 Manuel utilisateur

ESAB

ESAB EDB-15/30 Manuel utilisateur

ESAB

ESAB SDF-50 Manuel utilisateur

ESAB

ESAB PREST-O-LITE 02X93 Manuel utilisateur

ESAB

ESAB PREST-O-LITE PZ-503 Manuel utilisateur

ESAB

ESAB Origo Feed 304 P4 Mode d’emploi

ESAB

ESAB Versotrac EWT 1000 Manuel utilisateur

ESAB

ESAB TR-29 Manuel utilisateur

ESAB

ESAB PT-31XL Manuel utilisateur

Manuels Accessoires de soudage populaires d'autres marques

Lincoln Electric

Lincoln Electric LT-7 Tractor Manuel utilisateur

Weco

Weco Trolley R Manuel utilisateur

Cornwell Tools

Cornwell Tools MMWC1 Manuel utilisateur

Dohle

Dohle ExOn2A Manuel utilisateur

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manuel utilisateur

3M Speedglas 9100 Series Manuel utilisateur

Miller Electric

Miller Electric OM-842 Manuel utilisateur

Miller

Miller A-200 Series Manuel utilisateur

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manuel utilisateur

optrel

optrel lifeflip autopilot Manuel utilisateur

Miller

Miller MIGmatic M-25 Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manuel utilisateur

Abicor Binzel

Abicor Binzel xFUME PRO Manuel utilisateur

Sealey

Sealey SR20.V2 Manuel utilisateur

iWeld

iWeld NORED EYE Manuel utilisateur

Sthor

Sthor 74483 Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

Miller

Miller I-22 CE Manuel utilisateur