ESAB A2 S GMAW Mini Master Manuel utilisateur

Valid for Serial NO 930 XXX--XXXX0449 002 001 2001--03--12

A2 S GMAW Mini

Master

A2 SGF1

101103105107109111102021110025108024042106023061104022041100020040060001

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Instruction manual

Betriebsanweisung

Manuel d’instructions

Gebruiksaanwijzing

Instrucciones de uso

Istruzioni per l’uso

Manual de instruções

Ïäçãßåò ÷ñÞóåùò

-- 2 --

Rätt till ändring av specifikationer utan avisering förbehålles.

Ret til ændring af specifikationer uden varsel forbeholdes.

Rett til å endre spesifikasjoner uten varsel forbeholdes.

Oikeudet muutoksiin pidätetään.

Rights reserved to alter specifications without notice.

Änderungen vorbehalten.

Sous réserve de modifications sans avis préalable.

Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

Ci riserviamo il diritto di variare le specifiche senza preavviso.

Reservamo--nos o direito de alterar as especificações sem aviso prévio.

Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.

SVENSKA 3..............................................

DANSK 18................................................

NORSK 33................................................

SUOMI 48................................................

ENGLISH 63..............................................

DEUTSCH 78.............................................

FRANÇAIS 93.............................................

NEDERLANDS 109.........................................

ESPAÑOL 125..............................................

ITALIANO 141..............................................

PORTUGUÊS 156..........................................

ÅËËÇÍÉÊÁ 172.............................................

ENGLISH

-- 6 3 --

TOCe

1 DIRECTIVE 64........................................................

2SAFETY 64...........................................................

3 INTRODUCTION 66...................................................

3.1 General 66..................................................................

3.2 Technical data 66............................................................

3.3 Welding method 66...........................................................

3.4 Equipment 67................................................................

4 INSTALLATION 68....................................................

4.1 General 68..................................................................

4.2 Mounting 68.................................................................

4.3 Connections 69..............................................................

5 OPERATION 70.......................................................

5.1 General 70..................................................................

5.2 Start--up 70..................................................................

6 MAINTENANCE 74....................................................

6.1 General 74..................................................................

6.2 Daily 74.....................................................................

6.3 Periodic 74..................................................................

7 TROUBLE SHOOTING 75..............................................

8 ACCESSORIES 76....................................................

9 ORDERING OF SPARE PARTS 76......................................

10 WEAR COMPONENTS 77..............................................

DIMENSION DRAWING 188................................................

SPARE PARTS LIST 191...................................................

-- 6 4 --

fha8safe

1 DIRECTIVE

DECLARATION OF CONFORMITY

Esab Welding Equipment AB, S--695 81 Laxå, Sweden, gives its unreserved

guarantee that welding head A2 SGF1 from serial number 930 complies with

standard EN 60292 and EN 60204, in accordance with the requirements of directive

(89/392/EEC) and addendum (93/68/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Johnny Sundin

Design Manager, Div Engineering

Esab Welding Equipment AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411721

Laxå 1999--11--12

2SAFETY

Users of ESAB automatic welding machines have ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions.

The following recommendations should be observed in addition to the standard regulations that apply

to the work place.

All work must be carried out according to the specified instructions by personnel who are thoroughly

familiar with the operation of the welding machine.

Incorrect or unintentional operation of the equipment may lead to a hazardous situation which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the automatic welding machine must be familiar with:

Sits operation

Sthe location of emergency stops

Sits function

Srelevant safety precautions

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the machine when it is started

up.

Sthat no--one is in a hazardous position when the carriage or slide mechanisms are operated.

3. The work place must:

Sbe clear of mechanical components, tools, or other obstructions that could prevent the oper-

ator from moving freely within the working area.

Sbe organized so that there is free access to the emergency stop.

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, etc., which could become

trapped.

5. General precautions

Live electrical components are normally shielded from accidental contact.

SMake sure the return cable is connected securely.

SWork on high voltage components may only be carried out by a qualified electrician.

SAppropriate fire extinguishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during its operation.

WARNING

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND

OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR

EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON MANU--

FACTURER’S HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to keep fumes and gases from

your breathing zone and the general area.

ARC RAYS -- Can injure eyes and burn skin

SProtect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use ear defenders or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION

SCall for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

READ AND UNDERSTAND THE INSTRUCTION MANUAL

BEFORE INSTALLING OR OPERATING.

-- 6 5 --

fha8safe

-- 6 6 --

fha8d1ea

3 INTRODUCTION

3.1 General

The A2 SGF1 welding head is designed for MIG/MAG welding of butt and fillet joints.

A2 SGF1 is intended for use together with control box A2--A6 Process Controller and

ESAB’s LAF welding power source.

The welding head can be horisontally or vertically positioned by way of linear slides.

The angular motion can be freely adjusted by way of an angle slide.

Push angle for forehand welding or drag angle for backhand welding can be set

using the rotary attachment.

3.2 Technical data

A2 SGF1

Type of gas: Mix/Ar CO

Permissible load at 100 %: 600 A DC 650 A DC

Wire dimensions:

Non--alloy / Low--alloy

Stainless steel

Cored wire

Aluminium

1.0--1.6 mm

1.0--2.4 mm

1.0 -- 2.0 mm

1.0--1.6 mm

1.0--2.4 mm

Wire feed speed 2.0--25 m/min 2.0--25 m/min

Setting range, contact device ±45˚±45˚

Brake hub braking torque 1.5 Nm 1.5 Nm

Max. weight of wire 30 kg 30 kg

Weight (without wire):

with hand operated linear slides

with motor driven linear slides

15 kg

43 kg

15 kg

43 kg

Max. lateral inclination (whole unit) 25˚25˚

Setting length of the slide*

hand operated

motor driven

90 mm

180 mm

90 mm

180 mm

*) NB. Available in other lengths on request.

3.3 Welding method

MIG/MAG welding

In MIG/MAG welding the welding bead is shielded by way of shielding gas.

The welding head is water--cooled. The cooling water is connected to the respective

connection by way of hoses.

-- 6 7 --

fha8d1ea

3.4 Equipment

The complete welding head consists of a motor for the feed of the wire and contact

equipment supplying current to the wire.

Example of an A2 SGF1 with hand operated linear slides:

1. Wire feed unit with

four--wheel drive

2. Contact equipment containing

gas nozzle, contact device and

water hose

3. Angle slide

4. Linear slide (hand operated)

5. Wire feed motor

6. Wire drum

7. Wire conduit

8. Rotary attachment

Example of an A2 SGF1 with motor driven linear slides:

1. Wire feed unit with

four--wheel drive

2. Contact equipment containing

gas nozzle, contact device and

water hose

3. Angle slide

4. Linear slide (motor driven)

5. Wire feed motor

6. Wire drum

7. Wire conduit

8. Rotary attachment

Connection instructions for MIG/MAG welding, see the system diagram on page 69.

-- 6 8 --

fha8i1ea

4 INSTALLATION

4.1 General

The installation shall be executed by a professional.

WARNING!

Rotating parts can cause injury, take great care.

4.2 Mounting

The automatic welding machine can easily be mounted on a beam--travelling

carriage or on a welding column and boom unit by way of four M12 screws.

Make sure the bolts do not touch the bottom of the insulator, which has a thread

depth of 14 mm.

For mounting/ dismounting of A6 Slide, see instruction manual 443 394 xxx.

This safety sign is placed on the cover of the vertical slide.

-- 6 9 --

fha8i1ea

4.3 Connections

1. The A2--A6 Process Controller is to be connected by a qualified person.

2. For the connection of A6 GMD, see instruction manual 0443 403 xxx.

3. For the connection of A6 PAK, see instruction manual 0443 405 xxx.

4. Connect the welding head as follows:

SThe control cable (7) between the welding power source (8) and the A2--A6

Process Controller (2).

SThe return cable (11) between the welding power source (8) and the

workpiece (9).

SThe welding cable (10) between the welding power source (8) and the

welding head (1).

SThe gas hose (5) between the pressure reducing valve (6) and the gas valve

of the welding head (13).

SThe hoses for cooling water (3) between the cooling unit (4) and the welding

head (1).

SThe measuring cable (12) between the welding power source (8) and the

workpiece (9).

-- 7 0 --

fha8o1ea

5 OPERATION

5.1 General

General safety regulations for the handling of the equipment appear from

page 64. Read through before you start using the equipment!

SSelect wire type and shielding gas so that the weld material is as close as

possible to the analysis of the base material. Select wire size and welding data in

accordance with the values recommended by the consumables supplier.

SThorough joint preparation is necessary to achieve a good weld result.

NOTE! The width of the joint gap must be uniform.

STo minimise the risk of heat crack formation the width of the weld must be

greater than the penetration depth.

SAlways carry out a test weld with the same joint type and plate thickness as the

workpiece to be produced.

SFor control and adjustment of the welding head and welding power source, see

the instruction manual for the A2--A6 Process Controller.

SFor the replacement of wear parts, see table on page 77.

5.2 Start--up

NOTE!

The wire drum is not included in the delivery of the welding head in MIG design.

Fitting the wire drum

SFit the wire drum (1) on the brake hub (2).

Check that the carrier (3) is in the correct position.

NOTE! The maximum angle for the wire bobbin is 25°.

At extreme angles, wear will occur on the brake hub

locking mechanism and the wire bobbin will slide off

the brake hub.

IMPORTANT!

To prevent the reel sliding off the hub: Lock the reel in place

by turning the red knob as shown on the warning label atta-

ched next to the hub.

Table des matières

Autres manuels ESAB Accessoires de soudage

ESAB

ESAB SAVAGE A40 Manuel utilisateur

ESAB

ESAB SDF-50 Manuel utilisateur

ESAB

ESAB PSF 250 Manuel utilisateur

ESAB

ESAB ET 17 Manuel utilisateur

ESAB

ESAB Versotrac EWT 1000 Manuel utilisateur

ESAB

ESAB Eye-Tech 9-13 Manuel utilisateur

ESAB

ESAB Sentinel A50 Manuel utilisateur

ESAB

ESAB TR-29 Manuel utilisateur

ESAB

ESAB TIGAID315 AC/DC Manuel utilisateur

ESAB

ESAB Aristo W82 Manuel utilisateur

ESAB

ESAB A6 VEC Manuel utilisateur

ESAB

ESAB PSF 315ME Manuel utilisateur

ESAB

ESAB A6S Arc Master Manuel utilisateur

ESAB

ESAB PSF 260 Manuel utilisateur

ESAB

ESAB Origo Feed 304 P4 Mode d’emploi

ESAB

ESAB PC-900 Manuel utilisateur

ESAB

ESAB Warrior YardFeed 200 Manuel utilisateur

ESAB

ESAB PREST-O-LITE PZ-503 Manuel utilisateur

ESAB

ESAB Aristo U8 Manuel utilisateur

ESAB

ESAB EFU 30 Manuel utilisateur

ESAB

ESAB CIGWELD 454342 Manuel utilisateur

ESAB

ESAB Cigweld ProGuard Manuel utilisateur

ESAB

ESAB 1500 ahma Manuel utilisateur

ESAB

ESAB PSF 250 Manuel utilisateur

Manuels Accessoires de soudage populaires d'autres marques

Lincoln Electric

Lincoln Electric LT-7 Tractor Manuel utilisateur

Weco

Weco Trolley R Manuel utilisateur

Cornwell Tools

Cornwell Tools MMWC1 Manuel utilisateur

Dohle

Dohle ExOn2A Manuel utilisateur

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manuel utilisateur

3M Speedglas 9100 Series Manuel utilisateur

Miller Electric

Miller Electric OM-842 Manuel utilisateur

Miller

Miller A-200 Series Manuel utilisateur

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manuel utilisateur

optrel

optrel lifeflip autopilot Manuel utilisateur

Miller

Miller MIGmatic M-25 Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manuel utilisateur

Abicor Binzel

Abicor Binzel xFUME PRO Manuel utilisateur

Sealey

Sealey SR20.V2 Manuel utilisateur

iWeld

iWeld NORED EYE Manuel utilisateur

Sthor

Sthor 74483 Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

Miller

Miller I-22 CE Manuel utilisateur