ESAB PC-900 Manuel utilisateur

Mechanized Conversion Kit Installation Instructions

for PC-900

0558008549 04/2009

This equipment will perform in conformity with the description thereof contained in this manual and accompa-

nying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instruc-

tions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment

should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced imme-

diately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone

or written request for service advice be made to the Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.

The user of this equipment shall have the sole responsibility for any malfunction which results from improper

use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a ser-

vice facility designated by the manufacturer.

BE SURE THIS INFORMATION REACHES THE OPERATOR.

YOU CAN GET EXTRA COPIES THROUGH YOUR SUPPLIER.

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the

principles of operation and safe practices for arc welding and cutting equipment, we urge

you to read our booklet, “Precautions and Safe Practices for Arc Welding, Cutting, and

Gouging,” Form 52-529. Do NOT permit untrained persons to install, operate, or maintain

this equipment. Do NOT attempt to install or operate this equipment until you have read

and fully understand these instructions. If you do not fully understand these instructions,

contact your supplier for further information. Be sure to read the Safety Precautions be-

fore installing or operating this equipment.

CAUTION

USER RESPONSIBILITY

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

Users of ESAB welding and plasma cutting equipment have the ultimate responsibility for ensuring that

anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding or plasma cutting equipment. The following

recommendations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well acquainted with the operation of the welding or plasma

cutting equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in

injury to the operator and damage to the equipment.

1. Anyone who uses welding or plasma cutting equipment must be familiar with:

- its operation

- location of emergency stops

- its function

- relevant safety precautions

- welding and / or plasma cutting

2. The operator must ensure that:

- no unauthorized person stationed within the working area of the equipment when it is started up.

- no one is unprotected when the arc is struck.

3. The workplace must:

- be suitable for the purpose

- be free from drafts

4. Personal safety equipment:

- Always wear recommended personal safety equipment, such as safety glasses, ame proof

clothing, safety gloves.

- Do not wear loose tting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions:

- Make sure the return cable is connected securely.

- Work on high voltage equipment may only be carried out by a qualied electrician.

- Appropriate re extinquishing equipment must be clearly marked and close at hand.

- Lubrication and maintenance must not be carried out on the equipment during operation.

SAFETY PRECAUTIONS

WELDING AND PLASMA CUTTING CAN BE INJURIOUS TO YOURSELF AND

OTHERS. TAKE PRECAUTIONS WHEN WELDING OR CUTTING. ASK FOR

YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON

MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK - Can kill.

- Install and earth (ground) the welding or plasma cutting unit in accordance with applicable standards.

- Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

- Insulate yourself from earth and the workpiece.

- Ensure your working stance is safe.

FUMES AND GASES - Can be dangerous to health.

- Keep your head out of the fumes.

- Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

- Protect your eyes and body. Use the correct welding / plasma cutting screen and lter lens and wear

protective clothing.

- Protect bystanders with suitable screens or curtains.

FIRE HAZARD

- Sparks (spatter) can cause re. Make sure therefore that there are no inammable materials nearby.

NOISE - Excessive noise can damage hearing.

- Protect your ears. Use earmus or other hearing protection.

- Warn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

WARNING

Powercut-900

Mechanized Conversion Kit contents

p/n 0558008284

MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS

Item No. Part No. Qty Description

1 0558038337 1 PC BOARD - REMOTE

2 0558008457 1 RECEPTACLE / CABLE ASSY 14 PIN

3 952002 1 TOROIDAL CORE

4 951016 1 CONNECTOR COMBICON 10 PIN

5 951005 1 CONNECTOR COMBICON 3 PIN

6 526652 1 STRAIN RELIEF SEALED 1/2" ZINC

7 2062151 1 LOCKNUT CONDUIT 1/2"

8 * 0.75" HEATSHRINK 1" BLACK

9 * 1 CLAMP CABLE STEEL .375 DIA

10 * 2 SCREW HEX WSH TAP #8 x .438 RIBBED

11 * 5 TYWRAP SM 4"

12 0558008111 1 KIT JUMPER - MECHANIZED LOGIC

6, 7

2 wire connector cable

1. Access the inside of the PC-900 by unscrewing the

screws and removing the cover.

2. Assemble the strain relief onto the 14 pin cable as shown and partially tighten.

3. Remove the hole plug on the top right side of the back of the unit.

MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS

4. Cut the tie wrap, unplug control transformer

wires to allow for easier cable routing.

5. Thread the cable through the hole as shown

and allow cable to hang loose. Add locknut

and partially tighten. Add heatshrink to ca-

ble and leave loose, before applying clamp.

6. Assemble the cable clamp onto the exposed shield area and attach to the frame with the screw pro-

vided. Orient clamp downward as shown.

Cable clamp

Cable clamp in postion

Cut the tie wrap here

Heatshrink (leave loose)

7. Tighten the strain relief nut from the inside

rst and then tighten the outside strain re-

lief nut. Position heatshrink over threads to

prevent power leads from contacting sharp

edges. Electrical or other suitable tape may be

used if heatshrink gun is not available.

MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS

8. Addtoroidalcoretocableandleaveloose,before

installing connector. Align the 10-pin connec-

tor with the pc board header to identify which

end of the connector is pin 1 and therefore en-

sure proper connections of the 10 cables wires.

9. Install each wire and tighten. Cable wires are numbered 1 through 10 and must be connected in nu-

merical sequence starting with number 1. The pc board has been stamped with numbers 1 and 10 to

show the direction of sequence for the wires.

each wire is numbered

Heatshrink or suitable tape

Fast-on connectors

MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS

10. Connect the pc board to the main power control board as shown below. Connect the ring terminal

from the 14 pin cable and secure the pc board to the frame with the screw provided.

Install tie wrap as shown by arrow

11. Connect the fast-on connectors of the

"2-wire cable" to the 14 pin cable. Posi-

tion and tie wrap toroidal core.

12. Route the "2-wire cable" under the pc

board and tie wrap to the frame using

the provided holes in the areas shown.

13. Re-install the plug and tie wrap on the

previously unplugged wire.

Toroidal Core

Tie wrap

MECHANIZED CONVERSION KIT INSTALLATION INSTRUCTIONS

red wire "+"

black wire "-"

14. Route the "2-wire cable" downward behind the shelf brace.

15. Locate the 3-pin connector on the existing main power control board.

16. Align the 3-pin connector with the pc board header to identify which end of the connector aligns with

the "+" and "-" on the pc board. On the connector, insert the red wire to the "+" and black wire to the "-"

from the "2-wire cable" as shown and tighten.

17. Plug in the 3-pin connector on the pc board.

3-pin connector

Table des matières

Autres manuels ESAB Accessoires de soudage

ESAB

ESAB PT-31XL Manuel utilisateur

ESAB

ESAB CIGWELD Arcmaster 649 Payday Manuel utilisateur

ESAB

ESAB SDE-250 Manuel utilisateur

ESAB

ESAB 1500 ahma Manuel utilisateur

ESAB

ESAB Aristo MA4 Manuel utilisateur

ESAB

ESAB EDB-15/30 Manuel utilisateur

ESAB

ESAB SAVAGE A40 Manuel utilisateur

ESAB

ESAB SDF-250 Manuel utilisateur

ESAB

ESAB Warrior Feed 304 Manuel utilisateur

ESAB

ESAB Cigweld ProGuard Manuel utilisateur

ESAB

ESAB LAF 1601M Manuel utilisateur

ESAB

ESAB PSF 260C Manuel utilisateur

ESAB

ESAB EFU 30 Manuel utilisateur

ESAB

ESAB MXH 315 PP Manuel utilisateur

ESAB

ESAB A6S Arc Master Manuel utilisateur

ESAB

ESAB Warrior YardFeed 200 Manuel utilisateur

ESAB

ESAB PSF 260 Manuel utilisateur

ESAB

ESAB Aristo U6 Manuel utilisateur

ESAB

ESAB SAVAGE A40 Manuel utilisateur

ESAB

ESAB TWECO SPRAY MASTER V250 Guide de maintenance et de service

ESAB

ESAB Sentinel A50 Manuel utilisateur

ESAB

ESAB PREST-O-LITE 02X93 Manuel utilisateur

ESAB

ESAB WeldCloud Mobile Manuel utilisateur

ESAB

ESAB Eye-Tech 10-12 Select Manuel utilisateur

Manuels Accessoires de soudage populaires d'autres marques

Lincoln Electric

Lincoln Electric LT-7 Tractor Manuel utilisateur

Weco

Weco Trolley R Manuel utilisateur

Cornwell Tools

Cornwell Tools MMWC1 Manuel utilisateur

Dohle

Dohle ExOn2A Manuel utilisateur

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manuel utilisateur

3M Speedglas 9100 Series Manuel utilisateur

Miller Electric

Miller Electric OM-842 Manuel utilisateur

Miller

Miller A-200 Series Manuel utilisateur

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manuel utilisateur

optrel

optrel lifeflip autopilot Manuel utilisateur

Miller

Miller MIGmatic M-25 Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manuel utilisateur

Abicor Binzel

Abicor Binzel xFUME PRO Manuel utilisateur

Sealey

Sealey SR20.V2 Manuel utilisateur

iWeld

iWeld NORED EYE Manuel utilisateur

Sthor

Sthor 74483 Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

Miller

Miller I-22 CE Manuel utilisateur