Equinox Systems QUADZILLA Manuel utilisateur
Order code: EQLED51
user manual
www.prolight.co.uk
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Quadzilla Safety
Equinox Quadzilla Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the Equinox carton the following items:
1, Equinox Quadzilla 2, Power cable 3, Instruction manual
Technical Specications:
DMX channels: 6
Voltage: AC 240V - 50Hz
256 Ultra Bright LEDs (R: 96, G: 64, B:96)
Fuse: 1 Amp
Power Consumption: 45W
Dimensions: 935 x 155 x 195mm
Weight: 6.7Kgs
Operations:
There are 4 operating modes to choose from:
1, DMX Mode 2, Auto Run 3, Sound Active mode 4, Master/slave mode
DMX Mode
To select DMX mode, set dipswitch 10 to ON. You can now set the required DMX address using
dipswitches 1 to 9. The start address for this xture is 1. Please refer to the chart below for DMX
functions.
Auto Run Function Mode
To select auto pattern mode, set all dipswitches to the OFF position. The unit will now cycle through all
it’s built-in patterns. In this mode the LEDs will remain constantly chasing until the power is turned OFF
or the mode is changed.
Sound Active Mode
To select sound active mode set dipswitch 9 to ON. You can now use the sensitivity control on the back
panel to set the required sound input level. With no music present, the LEDs will turn OFF and will come
back ON as soon as the music starts again.
Slave Mode
Slave mode
To select the Slave mode, set dipswitch 1 to the ON position and all others to OFF.
The slave unit/s will now run in sequence with the master unit in any of the above master modes.
Equinox Quadzilla Technical specications
Master/Slave connection
1) Connect the 3-pin (male) connector of the DMX
cable to the output 3-pin (female) connector on
the master unit
2) Now connect the opposite end of the DMX cable
to the input socket on the slave unit/s.
Proceed to connect from the output as stated above
into the following xture and so on.
DMX Function Chart
Equinox Quadzilla Overview
Identication:
1, Hanging bracket
2, DMX input
3, DMX output
4, Dipswitches
5, Power input
6, Microphone
7, Sound sensitivity control
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the DATA
“IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have a data “out”
terminal).
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Quadzilla can be controlled via DMX-512 protocol. The DMX address is set on the back of
the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output
(gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Further DMX cables can be purchased from
all good sound and lighting suppliers or
Prolight dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Equinox Quadzilla DMX Set up
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.
Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of
erratic behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Quadzilla DMX Set up
Equinox Quadzilla Dip Switch Reference Chart
DMX Dip Switch Quick Reference Chart
Dip Switch Position
Dip Switch position DMX Address
www.prolight.co.uk
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Equinox Systems Équipement d'éclairage
Equinox Systems
Equinox Systems Gigabar MKII COB Manuel utilisateur
Equinox Systems
Equinox Systems Goboceptor Manuel utilisateur
Equinox Systems
Equinox Systems Fusion Orbit MKII Manuel utilisateur
Equinox Systems
Equinox Systems SpectraPix Lithium Batten Manuel utilisateur
Equinox Systems
Equinox Systems FLAM11 Manuel utilisateur
Equinox Systems
Equinox Systems Spectra Strobe Batten Manuel utilisateur
Equinox Systems
Equinox Systems Power Par Series Manuel utilisateur
Equinox Systems
Equinox Systems Party Par EQLED015 Manuel utilisateur
Equinox Systems
Equinox Systems Axis 50W Gobo Flower Manuel utilisateur
Equinox Systems
Equinox Systems COBALT Manuel utilisateur
Equinox Systems
Equinox Systems CARINA Manuel utilisateur
Equinox Systems
Equinox Systems 400W UV Cannon Manuel utilisateur
Equinox Systems
Equinox Systems Megabar System EQLED63 Manuel utilisateur
Equinox Systems
Equinox Systems Krypton EQLED21 Manuel utilisateur
Equinox Systems
Equinox Systems POLARIS Manuel utilisateur
Equinox Systems
Equinox Systems UV Mini Batten 9 Manuel utilisateur
Equinox Systems
Equinox Systems EQLED040 Manuel utilisateur
Equinox Systems
Equinox Systems Vortex Manuel utilisateur
Equinox Systems
Equinox Systems Saturn Spot Manuel utilisateur
Equinox Systems
Equinox Systems KAMIKAZE EQLA14 Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
