Equinox Systems MaxiPar Tri Manuel utilisateur

Order code: EQLED111

MaxiPar Tri

User Manual

www.prolight.co.uk MaxiPar Tri User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablevoltageisbetween

100~240V,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• WARRANTY:Oneyearfromdateofpurchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk MaxiPar Tri User Manual 3

Product overview & technical specications

Thiscompact,slimproleparisdesignedforuplightingaswellasstagelighting,andwillbringdeep,

richcolourstoanyeventorvenue.Itfeatures12x3Wtri-colourRGBLEDswhichoffersmoothcolourmixing.

OperationalmodesincludingDMX,auto,soundactiveandmaster/slavemodes.

•12x3Wtri-colourLEDs(RGB)

•Beamangle:25°

•1100Lux@2m(fullon)

•DMXchannels:6

•Auto,soundactiveand

master/slavemodes

•0-100%dimmingand

variablestrobe

•4pushbuttonmenu

withLEDdisplay

•Bracketallowsformultiplerigging

oroorstandingapplications

•Rubberfeetallowthepanel

tositatontheoorforuplighting

•SideentryXLRand

powerconnections

•IECpowerinput/output

•3-PinXLRinput/output

•Fancooled

MaxiPar Tri

Specications

Powerconsumption 40W

Powersupply 100~240V,50/60Hz

Fuse F1A250V

Dimensions 205x225x115mm

Weight 0.85kg

Ordercode EQLED111

205mm

225mm 115mm

0m 1m 2m 3m 4m 5m

25° - Lux

FULL ON

4400

836

3220

480

1100

209

804

120

489

357

25°

275

201

176

129

MAXIPAR

TRI

DMX OUTPUT

MIC

MODE DOWN UP ENTER

POWER OUTPUT

DMX INPUT

www.prolight.co.uk

POWER INPUT:

100-240V~50/60Hz

FUSE: F1A

MAXIPAR

TRI

DMX OUTPUT

MIC

MODE DOWN UP ENTER

POWER OUTPUT

DMX INPUT

www.prolight.co.uk

POWER INPUT:

100-240V~50/60Hz

FUSE: F1A

02 02

01 01

0503

01-Bracket

02-Brackettighteningknobs

03-LEDdisplay

04-Functionbuttons

05-Microphone

06-DMXinputsocket

07-DMXoutputsocket

08-IECpowerinputsocket

09-IECpoweroutputsocket

10-FuseF1A250V

Inthebox:1 x xture,

1 x power cable &

1 x user manual

www.prolight.co.uk MaxiPar Tri User Manual 4

Operating instructions

DMX mode:

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes

tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthe

xtureandeachxtureindependently.

ToaccesstheDMXaddressmode,pressthe“MODE”buttononthefrontoftheunittoshowA001

ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe

requiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

RGB colour mix mode:

Inthismodeyoucansetthexturetoanycolourandanybrightness.

Toaccessthecolourmixmodepress“MODE”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectPr00.

Pressthe“ENTER”buttontoshow r---with3digitsafterontheLEDdisplay.

Pressthe“ENTER”buttontoconrm.

Therrepresentsred,G=greenandb=blue.

The3digitsafterarethebrightnesssettingfrom000~255.

For example:

Ifyousetr,G,balltozero,yourunitwillhavenoLEDslitup(blackout).

Ifyousetr000tor255andGandbtozero,yourunitwillshowonlyredLEDs.

Pressthe“ENTER”buttontoconrmthesettingandmovetothenextcolour.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

6 channel mode:

Channel Value Function

CH1 000-255 Reddimmer(0-100%)

CH2 000-255 Greendimmer(0-100%)

CH3 000-255 Bluedimmer(0-100%)

CH4

000-027 Nofunction

028-055 Strobe(useCH6forspeed)

056-083 Strobewithcolourchange

(useCH6forspeed)

084-111 Red

112-139 Green

140-167 Blue

168-195 Yellow

196-223 Purple

224-251 Cyan

252-255 White

CH5

000 Nofunction

001-012 Redfadein/out

(useCH6

forspeed)

013-025 Greenfadein/out

026-038 Bluefadein/out

039-051 Yellowfadein/out

052-064 Purplefadein/out

065-077 Cyanfadein/out

078-090 Whitefadein/out

091-116 Autocolourfadein/out

117-142 Colourfade

143-168 Colourchange

169-181 Colourchangewithstrobe

182-207 Allautoshows

208-255 Soundactiveash(whenCH6is000)

208-255 Soundactive(whenCH6is001-255)

CH6 000-255 Speed(slow-fast)/Sensitivity(low-high)

www.prolight.co.uk MaxiPar Tri User Manual 5

Built-in program mode:

Toaccessbuilt-inprogrammodepress“MODE”untilthedisplayshowsPr--ontheLEDdisplay.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectbetweenPr00~Pr13.

Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectthespeedbetween

SP00~Sp20.Pressthe“ENTER”buttontoconrm.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Sound active mode:

Toaccessthesoundactivemode,pressthe“MODE”buttononthefrontoftheunittoshowSoudon

theLEDdisplay.Nowpressthe“ENTER”buttonandthedisplaywillshowSens.Pressthe“ENTER”

buttonagainandusethe“UP”and“DOWN”buttonstoselectthesensitivitylevelfrom000-100.

Pressthe“ENTER”buttontoconrmthesetting.

Value: 000 - 100 (000 = low,100 = high)

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Master/slave mode:

Tosetthemasterunit,pressthe“MODE”buttonontherearofthemasterunittoselectyour

desiredprogram(soundactiveorRGBcolourmix).

Tosettheotherunitsinslavemode,pressthe“MODE”buttonontherearoftheunittoshowSLav

ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin

sequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Built-inprogrammode

Pr00-Pr13

Pr00-RGBcolourmixmode

Pr01-R

Pr02-G

Pr03-B

pr04-RG

Pr05-RB

Pr06-GB

Pr07-RGB

Pr08-Colourfadein-out(3colours)

Pr09-Colourfadein-out(7colours)

Pr10-Colourfade

Pr11-Colourfadein-out(7colours)&colourfade

Pr12-Colourchange(3colours)

Pr13-Colourchange(7colours)

Staticcolourmode r000~r255R

G000~G255G

b000~b255B

Slavemode SLAV

Soundactivemode SOUd

Sens

000~100

DMXmode 6CH

Addresssetting A001~A512

Menusystem

www.prolight.co.uk MaxiPar Tri User Manual 6

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk MaxiPar Tri User Manual 7

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterferance.itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk MaxiPar Tri User Manual 8

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof

withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe

environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother

typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.

Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir

localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally

saferecycling.

Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe

purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Equinox Systems Équipement d'éclairage

Equinox Systems

Equinox Systems Nova Par 64 Manuel utilisateur

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Manuel utilisateur

Equinox Systems

Equinox Systems Goboceptor Manuel utilisateur

Equinox Systems

Equinox Systems Fusion 150 Manuel utilisateur

Equinox Systems

Equinox Systems Nimbus Manuel utilisateur

Equinox Systems

Equinox Systems 400W UV Cannon Manuel utilisateur

Equinox Systems

Equinox Systems ORION Manuel utilisateur

Equinox Systems

Equinox Systems Saturn Spot Manuel utilisateur

Equinox Systems

Equinox Systems Domin8r IIEQLED53 Manuel utilisateur

Equinox Systems

Equinox Systems EQLED203 Manuel utilisateur

Equinox Systems

Equinox Systems Gigabar MKII COB Manuel utilisateur

Equinox Systems

Equinox Systems CARINA Manuel utilisateur

Equinox Systems

Equinox Systems FUSION SPOT XP Manuel utilisateur

Equinox Systems

Equinox Systems ATRIA Manuel utilisateur

Equinox Systems

Equinox Systems Lighting strike STRO21 Manuel utilisateur

Equinox Systems

Equinox Systems Power Par Series Manuel utilisateur

Equinox Systems

Equinox Systems QUADRILLE Manuel utilisateur

Equinox Systems

Equinox Systems Eyebar Manuel utilisateur

Equinox Systems

Equinox Systems XP 80W Manuel utilisateur

Equinox Systems

Equinox Systems Fusion 260ZR Manuel utilisateur

Equinox Systems

Equinox Systems PIXELpoint Batten Manuel utilisateur

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Manuel utilisateur

Equinox Systems

Equinox Systems UV Mini Batten 9 Manuel utilisateur

Equinox Systems

Equinox Systems VS 1500 Fogger Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur