Epson PowerLite 50c Manuel utilisateur

EPSON®PowerLite®50c/70c

Quick Setup

Connect the power cord to your projector and plug the other end into a grounded outlet.

3Connect the other end to your laptop’s video or monitor port.

1Turn on the projector first. To do so, press the red Power button.

The power light flashes green as the projector warms up,

and the projection lamp comes on in about 30 seconds.

2Turn on or restart your laptop. (Windows®only: If you see a

New Hardware Wizard screen, click Cancel.)

Turn Over

Press the red Power button twice, then let the projector cool while the power light

flashes orange (about a minute). Once the light stops flashing and stays on, it’s safe to

unplug the projector.

Never unplug the projector when the power light is green or flashing orange.

Locate everything

you’ll need

Plug in your projector

Turn on your equipment

Caution: Before unplugging the projector...

For most setups, you’ll need just these two cables:

You won’t need to install any software.

Power

Help

Make sure your projector and laptop are turned off.

Connect one end of the computer cable to the

Computer port on the projector.

Connect the projector

to your laptop

power cord computer cable

Follow these instructions to connect the projector

to your laptop. To connect other devices, such as

a VCR or desktop PC, see your User’s Guide.

power button

power light

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

Autres manuels pour PowerLite 50c

Table des matières

Autres manuels Epson Projecteur

Epson

Epson PowerLite Pro G6550WU Manuel utilisateur

Epson

Epson PowerLite D6150 Manuel du système

Epson

Epson BrightLink 455Wi Manuel utilisateur

Epson

Epson VS335W Manuel utilisateur

Epson

Epson CO-W01 Manuel utilisateur

Epson

Epson EMP-703 Manuel utilisateur

Epson

Epson PowerLite home cinema 3010e Manuel utilisateur

Epson

Epson PowerLite 750HD Manuel utilisateur

Epson

Epson 6100i - PowerLite XGA LCD Projector Manuel utilisateur

Epson

Epson EB-L200W Manuel utilisateur

Epson

Epson PowerLite 1915 Manuel utilisateur

Epson

Epson PowerLite 4100 Manuel du système

Epson

Epson EMP-8000 - XGA LCD Projector Manuel utilisateur

Epson

Epson EB-G5350 Manuel utilisateur

Epson

Epson VS200 Manuel utilisateur

Epson

Epson V11H281020 - PowerLite 400W WXGA LCD... Guide de référence

Epson

Epson POWERLITE 83V+ Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Epson

Epson EH-TW9300W Manuel utilisateur

Epson

Epson BrightLink 455Wi Manuel utilisateur

Epson

Epson EB-1945W Manuel utilisateur

Epson

Epson 7850p - PowerLite XGA LCD Projector Manuel utilisateur

Epson

Epson EB-905 Manuel utilisateur

Epson

Epson PowerLite 737c Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Manuel utilisateur

JVC

JVC 1108TTH-AO-AO Manuel utilisateur