Epson SG-WRITERII Instructions d'utilisation

Rev.7.4

WRITER

Application Manua

Rev.7.4

For safe usage

Guide to symbols

Safety Precautions

Before Use

The following signs are used in order to ensure correct and safe product usage and to prevent personal

injury or property damage.

Their meanings are as follows. Please read and understand the contents before reading the text.

 The product referred to in this document is for general consumer use. Do not use it in a life

support system or in other applications that require extremely high reliability.

 Do not continue operating if you notice smoke, unusual odors or sounds.

Continued operation may result in electric shock or fire.

Immediately remove the USB cable and contact your dealer or your nearest EPSON sales

representative.

Due to the danger, do not attempt repairs yourself.

 Do not disassemble or modify the product in any way.

Doing so may result in injury, electric shock or fire.

 Do not supply power from sources other than the USB cable

Using other power sources may result in electric shock or fire.

 Do not handle the USB cable with wet hands.

Doing so may result in electric shock.

 Please read the instructions carefully and use correctly

WARNING

This mark indicates the nature of a hazard that could potentially result in death or

serious injury if instructions are ignored and the product is used improperly.

CAUTION

This mark indicates the nature of potential personal injuries or potential property

damage if instructions are ignored and the product is used improperly.

WARNING

Rev.7.4

 Do not insert or drop any foreign objects into the product.

Doing so may result in fire or electric shock.

 If water or other liquid enters the product, immediately remove the USB cable and contact your

dealer or your nearest EPSON sales representative.

There is the risk of fire or electric shock.

 Do not place the product on an unstable surface (such as an unsteady table or inclined surface)

Doing so could result in injury should the product fall or collapse.

 Do not install or store in dusty locations or locations subject to high humidity.

Doing so could result in breakdown, fire or electric shock.

 Do not climb or place heavy objects on this product.

Doing so could result in injury from falling or breakage.

 To ensure safety, remove the USB cable when the product is not in use.

 Abide by national and local regulations when disposing of this product. Please ask about the

regulations in your country and locality.

WARNING (Continued)

CAUTION

Rev.7.4

Index

1 SG-WRITER Components 1

2 USB Driver Installation 1

3 Software Installation 3

4 SG-8018/SG-8101/9101 Operation Procedures 4

5 SG-85xx Operation Procedure 6

6 SG-8002/8003 Operation Procedure 7

7 Hardware Specifications 12

8 Table of Error Messages 13

9 Warnings and Cautions 14

1 Rev.7.4

1. SG-WRITER Components

1)Components

 SG-WRITERII

 Documents

 Please download SG-Writer software and USB Driver from HP.

http://www5.epsondevice.com/en/information/support/sg8000/sg_writer2_software.html

2) Customer-prepared Items

(1) PC

 Available OS: Windows 10(32bit, 64bit), Windows 7(32bit, 64bit), Windows Vista(32bit), Windows XP(32bit)

 Recommend CPU: Pentium4 1.4GHz or better

 Recommended memory capacity: Over 512MB(Windows XP 32bit), Over 1GB(Windows 10/7/Vista 32bit),

Over 2GB(Windws10/7/Vista 64bit).

(2) USB Cable (mini B)

2. USB Driver Installation

1) Driver Package

WinUSBDriver folder

- x86 folder: driver files for 32bit version Windows7, Vista.

- ams64 folder: driver files for 64bit version Windows7, Vista.

- XP_x86 folder: driver files for 32bit version Windows XP.

2) Installation Procedure

(1) Installation procedure for systems running Windows 10/7/Vista

a. Run dpinst.exe in the amd64 folder for 64bit version windows, and in the x86 folder for 32bit version

Windows.

b. The "Welcome to the Device Driver Installation Wizard!" dialog appears. Click "Next".

c. The "Would you like to install this device software?" dialog appears. Click "Install".

d. Driver installation is complete, so click "Finish".

(2) Installation procedure for Windows XP

a. Connect the SG-WRITER to the USB port.

b. The "Found New Hardware Wizard” dialog appears. Check the "Install from a list or specified location" box

(name may be slightly different), then click "Next".

c. Click the "Search for the best driver in these locations." radio button.

d. Check the "Include this location in the search:" box, and click "Browse...", and specify the directory

“XP_x86”. After specifying the directory, click "OK".

e. Because the driver has not passed WHQL certification for Windows XP, a warning message appears.

Click "Continue" to move to the next step.

f. Driver installation is complete, so click "Finish".

2 Rev.7.4

3) Uninstall Procedure

(1) Uninstall procedure for Windows 10/7/Vista

Click on the Start menu, and click "Control Panel".

Click "Uninstall a program" to view a list of currently installed programs.

Then, double-click "Windows Driver Package – SEIKO EPSON CORPORATION(WinUSB) USB" In the

list.

The "All devices using this driver will be removed. Do you wish to continue?" dialog appears. Click "OK".

(2) Uninstall procedure for Windows XP

a. Launch Device Manager.

Click on the Start menu, go to "Settings" and click "Control Panel". Double-click the "System" icon to

display the "System Properties" screen. Click the "Hardware" tab, then click the "Device Manager…"

button to launch Device Manager.

b. Delete the driver.

Click "Universal Serial Bus controllers" to view a list of controllers contained therein. Then, double-click

"EPSON SGWRITERII" In the PROM Writer Properties window, click on the "Driver" tab, and then click

"Uninstall." The "Confirm Device Removal" dialog appears. Click "OK".

3 Rev.7.4

3. Software Installation

Please download SG-Writer software from HP.

1) Software structure

 SGWriter.exe - executable program file

 Sglib.dll - library file

 SGWriterLib03.dll - library file

 SGWriterLib04.dll - library file

 mfc100.dll - run time library

 msvcr100.dll - run time library

2) Installation Procedure

a. Copy software files to the same directory.

b. Connect the SG-WRITER to a PC. A USB cable is required.

c. Double-click the executable file SGWriter.exe

d. “Select Deivce” window is appeared.

Click the button of the device to programming.

- SG-8018 / SG-8101 / SG-9101, SG85xx, SG-8002 / SG-8003

.net framework 4

To use this software. The installation of net framework4 is needed. Please the warning message "Please

install microsoft .net framework 4.” must be displayed when it is not installed, and download from the site of

Microsoft, and install it. Please refer to the Web site of Microsoft for the installation method.

https://www.microsoft.com/en-us/download/details.aspx?id=17718

If "SG-8002/SG-8003" is clicked when the SG-WRITER is not connected to a PC, a screen such as that

shown below appears, and the software will start up in a mode that enables calculations only. To write and

perform measurements, click "No." Then, after checking that the SG-WRITER and PC are connected, once

again double-click SGWriter.exe to execute the program.

4 Rev.7.4

4. SG-8018/SG-8101/SG-9101 Operation Procedures

4-1. SG-8018/SG-8101/SG-9101 Programming Operation

a. Enter Operation Buttons

(1) Model name Select SG-8018 / SG-8101 / SG-9101

(2) Package type Select package CA/CB/CE/CG

(3) Frequency Enter frequency

(4) Vcc Select power voltage

(5) Temperature Select G:-40~+85degC/H:-40~+105degC

(6) OE Function Select OE Terminal Function P(Output Enable) / S(Standby)

(7) Slew rate Select Slew rate A:Default/B:Fast/C:Slow

(8) Tolerance Select frequency tolerance B/C/J

(9) SS Function (SG-9101)

Select Modulation, rate, Profile

b. Click “CheckParameter” button.

When Programing is possible, “Burn” button is enabled.

c. Set the product (SG8018/SG8101/SG9101) in the PROM WRITER socket.

 Set the product with the lever up. SMD devices need adapter socket

 Keep the product in place by lowering the lever.

 Do not carry the product (SG8018/SG8101/SG9101) in your hand.

 Do not expose the product to static electricity. (Remove electricity with a wrist strap.)

d. Execute Writing, Click the “Burn” button.

e. In the case of acceptable product, “Programming procedure … OK” will be displayed in the message box.

An error message will be displayed in the case of defects.

f. Raise the lever and remove the product (SG8018/SG8101/SG9101).

 Do not carry the product (SG8018/SG8101/SG9101) in your hand.

 Do not expose to static electricity. (Remove electricity with a wrist strap, etc.)

(1)

Model name

a.(2) Package type

a.(3) Frequency

a.(4

)

Vcc

a.(5

)

Temperature

a.(6

)

OE function

a.(7

)

Slew rate

a.(8

)

Tolerance

a.(9

)

SS function

b. Check Parameter

Order code Box

Message Box

Programming counter

5 Rev.7.4

4-2. SG-8018/SG-8101/SG-9101 Check Device Operation

a) Set the product (SG8018/SG8101/SG9101) in the PROM WRITER socket.

b) Execute “CheckDevice” button.

c) An Order Code or “Blank Sample” messages is displayed in the “Order code box”

d. “Write” Programming device

Order code Box

“CheckDevice”

6 Rev.7.4

5. SG-85xx Programming Procedures

5-1. SG-85xx Programming Operation

a. Enter Operation Buttons

(1) Model name Select SG-8503CA / SG-8504CA / SG-8506CA

(2) Frequency Enter frequency

(3) OE Polarity Select OE Polarity Positive / Negative

(4) OE Standby type Select OE Standby type Hi-Z / OUT_L

(5) I2C slave address Enter I2C slave address(SG-8506CA)

c. Set the product (SG85xx) in the PROM WRITER socket.

 Set the product with the lever up. SMD devices need adapter socket

 Keep the product in place by lowering the lever.

 Do not carry the product (SG85xx) in your hand.

 Do not expose the product to static electricity. (Remove electricity with a wrist strap.)

d. Execute Writing, Click the “Write” button.

e. In the case of acceptable product, “Programming is completed!!” will be displayed in the message box.

An error message will be displayed in the case of defects.

f. Raise the lever and remove the product (SG85xx).

 Do not carry the product (SG85xx) in your hand.

 Do not expose to static electricity. (Remove electricity with a wrist strap, etc.)

5-2. SG-85xx Check Device Operation

a) Set the product (SG85xx) in the PROM WRITER socket.

b) Execute “Check” button.

c) Programmed settings or “Blank device” messages is displayed in the “Message box”

(1)

Model name

a.(2) Frequency

a.(3

)

OE Polarity

a.(4

)

OE Standby type

b. Check Parameter

Message Box

Table des matières

Autres manuels Epson Carte mère

Epson

Epson S5U13A05B00C Manuel utilisateur

Epson

Epson S5U13706P00C100 Manuel utilisateur

Epson

Epson S5U13705B00C Manuel utilisateur

Epson

Epson S5U13A05B00C Manuel utilisateur

Epson

Epson S5U13700P00C000 Manuel utilisateur

Epson

Epson S1R72V18 Manuel utilisateur

Epson

Epson S1C31D50 Manuel utilisateur

Epson

Epson S1S65010 Manuel utilisateur

Epson

Epson S5U13705B00C Manuel utilisateur

Epson

Epson S5U1C17F57T Manuel utilisateur

Epson

Epson Buzzer S1C31D51 Manuel utilisateur

Epson

Epson 5U13743P00C100 Manuel utilisateur

Epson

Epson S1V30120 Manuel utilisateur

Epson

Epson S5U13L01P00C100 Manuel utilisateur

Epson

Epson S5U1C6S3N2E2 Manuel utilisateur

Epson

Epson S5U13C00P00CX00 Manuel utilisateur

Epson

Epson S5U1C17M03T Manuel utilisateur

Epson

Epson S5U13781R00C100 Manuel utilisateur

Epson

Epson S1V30000 Series Guide de l'utilisateur

Epson

Epson S5U13506P00C100 Manuel utilisateur

Epson

Epson S1D13C00 Manuel utilisateur

Epson

Epson S1R72U06 Manuel utilisateur

Epson

Epson S5U13706B00C Manuel utilisateur

Epson

Epson S5U13A04B00C Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur