EOS EMOTEC DC 9000 Manuel utilisateur

IP x4

Made in Germany

Druck Nr. 29344198en / -23.12

EMOTEC DC 9000

GB Assembly and operating instruction

2GB

English

Table of Contents

Package contents ..................................................................................................4

Optional connections: ........................................................................................4

Technical data .........................................................................................................5

General information concerning sauna bathing ......................................................6

General safety precautions .....................................................................................7

Assembly of the control unit ....................................................................................8

Wall mounting....................................................................................................8

Electrical connection ...............................................................................................9

Connecting the sauna oven ....................................................................................9

Connecting the sauna lamp ............................................................................10

Connecting a fan .............................................................................................10

Connecting a power control unit ......................................................................10

Connecting a colored light ...............................................................................10

Connecting the remote button .........................................................................10

Connecting a GSM module .............................................................................10

Connecting the phase section module for LED/spot lights ..............................10

Connecting the switch module for energy-saving lamps .................................10

Installation diagram .........................................................................................11

Terminal arrangement on the circuit board. .....................................................11

Sensor connection ..........................................................................................12

Connection of sauna heaters ≤ 9 kW ..............................................................12

Connection of sauna heaters > 9 kW ..............................................................13

Connecting the sensor lines ............................................................................14

Mounting the oven sensor ...............................................................................14

Installing the optional bench sensor ................................................................15

Operation ..............................................................................................................16

Button functions ..............................................................................................16

Symbol description ..........................................................................................16

Initial unit switch-on ..............................................................................................17

Preset parameters ...........................................................................................18

Finnish sauna mode ........................................................................................18

Temperature display ........................................................................................18

Actual - target display ......................................................................................18

Heating time ....................................................................................................18

To consider when programming: ...........................................................................19

The keylock / hotel mode ......................................................................................20

Specialist section ..................................................................................................21

F1 Setting the current time ..............................................................................21

F5 Link color light options with heater .............................................................22

F8 The optional bench sensor .........................................................................23

F10 Reset time from the submenus ................................................................24

Programming levels ..............................................................................................25

P1 Starting with the time preselection .............................................................25

Deactivating the time preselection ..................................................................26

P2 Heating time limitation ...............................................................................26

Activation of the weekly timer ..........................................................................27

P0 Weekly timer ..............................................................................................27

P1 Starting with time preselection in weekly timer mode ................................28

P5 Temperature setting ...................................................................................30

P6 Programming fan operation .......................................................................31

P7 Ability to dim the cubicle lights ...................................................................32

Coloured light (optional) ..................................................................................33

P9 Setting the time interval for the coloured light ............................................35

The control unit switch (Switch-off) ......................................................................36

Switching over the heating time limitation for commercial use or weekly timer ....36

Error display ..........................................................................................................37

Other error options that are not displayed and their causes: ..........................37

Service Address: ...................................................................................................38

Guarantee .............................................................................................................38

Handling procedures for return shipments (RMA) - Details for all returns ! ..........39

4GB

Package contents

(subject to change)

Included with the control unit are:

1. An heater-sensor board with overheat shutoff protection, KTY-sensors with sensor housing

, two 3x25 mm fastening screws and a 2,0 m long sensor cable, red and white.

2. A plastic bag with three 4 x 20 mm fastening screws.

3. A replacement overheat protection module.

Optional connections:

Bench sensor Art. No: 94.4389

Colored light module Art. No: 94.2761

Neon colored light module Art. No: 94.4286

EmoLux colored light module Art. No: 94.4834

Remote start button Art.No: 94.4645

Connection line 10m Art.No: 94.4646

Connection line 25m Art.No: 94.4647

Connection line 50m Art.No: 94.4648

emotion of sauna.

GSM mobile phone remote switch modul Art.No: 94.4671

Phase angle control

module for LED-/Halogen spotlights Art.No: 94.4970

Control module for energie-saving

(uorescent) lamps Art.No: 94.4669

Technical data

Nominal voltage: 400 V 3 N AC 50 Hz

Switching load: max. 9 kW Ohm resistive load (AC1 - mode)

device can be extended by connecting powered control units

up to 36 kW

Heating time limit: 6 hr, 12 hr or no heating time limit

Display: Jumbo backlit LCD

Protection class: IPx4 in line with EN 60529 splashed water resistant

Normal range for sauna: 30 to 110°C

Sensor system: KTY sensor with safety temperature limiter 142°C

Control characteristic: digital two-point regulation

Fan output: min. 25 W max.100 W (only fan excluding capacitor)

Light: min. 25 W max.100 W Only ohm resistive load, we recommend

to use special bulbs like baking oven bulbs. Other lamps have to

use with the optional control modules.).

Coloured light (optional): max. 100 W per colour

Colour on-time: 1 - 10 min

Colour order: red - red/yellow - yellow - yellow/green - green - green/blue - blue

- blue/red

Error display: via warning triangle (ashing) and error code on LCD

Ambient temperatures: -10°C to +35°C

Storage temperatures: -20°C to +60°C

Fuse protection on the light and the ventilation can

be a maximum of 1A delay action. There is a danger

of re if greater fuse protection is used!

6GB

Dear customer,

with purchase of this sauna control unit you

opted for a superior quality, high-tech elec-

tronic device which was developed and ma-

nufactured to meet the highest standards of

quality and safety.

Please note that an optimal interaction of

sauna cabin, sauna oven and sauna control

unit is mandatory for a pleasant sauna cli-

mate in your cabin.

With this sauna control unit you can operate

your sauna heater and thanks to the indivi-

dual programming settings you will surely

soon nd the setting that suits you best.

Perception in the sauna is very subjective,

therefore it really requires your own prefe-

rence, or that of your family to nd the most

suitable settings.

By default the nnish sauna is preset to

95°C. For steam operation the values are

set to 60°C and 60% humidity.

The following operation instructions describe

how to pre-select „your“ climate in the cabin.

Read these instructions carefully, so that you

quickly and easily nd your way though the

programming process.

Please note the variation in temperatures in

the cabin while sauna bathing. The hottest

area is directly under the cabin ceiling, whe-

reas there is a steady temperature gradient

towards the oor of the cabin. Inversely, the

relative humidity is lowest directly under the

cabin ceiling and the highest on the cabin

oor.

For safety reasons the temperature sensor

with the overheat limiter is located on the ca-

bin ceiling above the oven, since this is the

hottest area in the cabin.

Therefore there will always be temperature

variations between the temperature sensor

of the control unit and the thermometer in

the cabin.

General information concerning sauna bathing

For the cabin light use only light bulbs. Do

not use uorescent lamps, energy saving

lamps and gas discharge lamps.

For example, when pre-setting the cabin

temperature to 100°C, the thermometer in-

side the cabin may easily show 85°C - 90°C.

This complies with the typical climate inside

the cabin.

Always observe hygiene. Always use hand-

or bathing towels, to avoid getting perspirati-

on on the wood.

To protect your cabin from possible dama-

ges due to steam operation, we recommend

reheating or drying the cabin after every

steam bath.

In addition, a fan can help to dissipate used

humid air in badly ventilated areas.

To avoid the perception of draft, you should

avoid using any ventilation system while

sauna bathing. It should only be used if re-

commended by the cabin manufacturer

Always make sure no objects are

located on the sauna oven before

starting the heating cycle.

General safety precautions

• his device has not been designed for being

used by persons (including children) that

are physically or mentally handicapped

or have sensory disabilities. Moreover, it

is not allowed to use this device without

sufcient experience and/or knowledge,

unless these persons will be supervised

by persons responsible for their security

or in case they have been instructed how

to use this device.

• Children are to be supervised in order to

make sure that they do not play with this

device.

• Attention: It is forbidden to install

the control box in a closed switch ca-

binet or behind a wooden panelling!

• The electrical installation may be done

only by a qualied electrical technician.

• You must comply with the regulations of

your power supply company and applica-

ble VDE regulations (DIN VDE 0100).

• WARNING: Never attempt repairs

or installations yourself, as this could

result in serious injury or death. Only a

qualied technician may remove the hou-

sing cover.

• Please note the dimensions in the assem-

bly instructions, especially when installing

the temperature sensor. The temperature

above the oven is critical for the tempera-

ture setting. The temperature can be held

within operating parameters and a mini-

mal temperature gradient inside the bench

area of the sauna cabin can be achieved

only if unit is assembled correctly.

• The device may only be used as intended

as a control unit for sauna ovens up to 9

kW (up to 36 kW when combined with a

contactor box).

• Completely disconnect the control unit

from the electrical circuit, i.e. ip all circuit

breakers or the main circuit breaker during

each installation or repair.

• Please note the safety and installation in-

formation from the sauna oven manufac-

turer.

• Always heed the specications and in-

structions of the cabin manufacturer, too.

Attention!

Dear customer,

according to the valid regulations, the

electrical connection of the sauna hea-

ter and the control box has to be carried

out through the specialist of an authori-

zed electric shop

We would like to mention to the fact

that in case of a warrenty claim, you

are kindly requested to present a copy

of the invoice of the executive electric

shop.

When using control units that offer the

possibility of external access (GSM-module,

remote button, etc.) or time-delayed swit-

ching (preselection time, weekly timer, or

similar) a trigger guard with covered heating

unit is required. (cover protection type 1-5 or

S-Guard).

8GB

Assembly of the control unit

Wall mounting

Mount the control unit outside the sauna

cabin only. The most practical mounting

point would be the wall area onto which

the sauna oven is mounted on the inside,

except on the outside of the cabin. If elec-

trical conduits are present, mount the con-

trol unit accordingly. To mount the control

unit, please follow these instructions:

Illust. 1

1. Remove the cover of the control unit. To

do this press the fastening tab inwards

with a at screwdriver and remove the

housing top by pivoting it upwards (Il-

lust.1). Drill the threaded holes for the

included 4 x 20 mm wood screws accor-

ding to Illust. 3 & 3.1.

2.Insert one of the wood screws into the

upper middle hole. This screw will be the

mounting point for the control unit. Make

sure the screw is projecting out from wall

about 3 mm. (Illust. 3.2)

3. Hang the control unit onto the 3 mm pro-

jecting screw. Insert the included rubber

sleeves into the openings on the back

side of the housing and lead the electri-

cal cable through these openings. Screw

the lower part of the housing onto the ca-

bin wall using the lower threaded holes.

(Illust. 4)

Illust. 3

eye level

Illust . 3.2

Illust . 4

feed-through channel for

power supply lead wire

oven supply line

vaporizer supply line

lamp

fan

feed-through

channel for

sensor lines

upper threaded hole

threaded holes

Illust. 3.1

ca. 34 cm

17,4 cm

19 cm

eye level

Assemble the sauna oven according to the

instructions provided by the manufacturer in

front of the air intake opening.

Lead the silicone wire to the power control

unit through the ducts and connect them to

the corresponding terminals according to cir-

cuit diagram.

Note: If no ducts are available, bore a hole

next to the air inlet opening and pull the sto-

ve wire/s to the outside to lead them to the

corresponding terminals in the control unit.

In order to protect the silicone wire from ex-

ternal impacts it should be covered. There-

fore use a suitable cable duct or a PVC pipe

in which you lead the wire/s to the power

control unit.

Lead the power cord to the control unit and

connect it to the power inlet terminal.

Electrical connection

The electrical connection may only be

done by a qualied electrical technician

under authority of the regulations of the

local power supply company and those

of the VDE.

In general, there can only be one permanent

connection to the power supply network, to

include a device which allows the unit to be

disconnected from the power source with a

contact distance of at least 3 mm from all

terminals.

All electrical installations and connector ca-

bles inside the cabin must be able to with-

stand temperatures up to 170°C.

Connecting the sauna

oven

10 GB

Connecting the sauna lamp

The sauna lamp must be weatherproof pro-

tected (IPx4) and resistant to the ambient

temperature.

The sauna lamp can be mounted at any

point, but never near to rising hot air from

the heater and as far as possible from the

installation position of the IR lamp (may not

in the direct beam).

Connecting a fan

The fan must be weatherproof protected

(IPx4) and resistant to the ambient tempera-

ture.

The fan can be mounted at any point, but

never near to rising hot air from the heater

and as far as possible from the installation

position of the IR lamp (may not in the direct

beam).

emotion of sauna.

LSG

Connecting a colored light

Connecting a GSM module

Connecting a power control

unit

Details can be found in the colored light as-

sembly instructions.

Details can be found in the GSM module as-

sembly instructions.

Details can be found in the power control

unit assembly instructions.

Connecting the remote but-

ton

Details can be found in the remote button

assembly instructions.

Details can be found in the switch module

assembly instructions.

Connecting the phase sec-

tion module for LED/spot

lights

Connecting the switch mod-

ule for energy-saving lamps

Details can be found in the switch module

assembly instructions.

Only ohm resistive load, we

recommend to use special bulbs

like baking oven bulbs.Other bul-

bs, like energy-saving-lamps can

destroy the control unit.

Autres manuels pour EMOTEC DC 9000

Table des matières

Autres manuels EOS Unité de contrôle

EOS

EOS Saunabus Soundmodul Series Manuel utilisateur

EOS

EOS SBM-App Manuel utilisateur

EOS

EOS SBM App Module Instruction manuelle

EOS

EOS ECON H4 Guide de l'utilisateur

EOS

EOS WCI-01 Manuel utilisateur

EOS

EOS EmoTouch II + Manuel utilisateur

EOS

EOS ECON D4 Manuel de la liste des pièces

EOS

EOS EmoTouch 3 Manuel utilisateur

EOS

EOS ECON S2 Manuel utilisateur

EOS

EOS InfraStyle Manuel utilisateur

EOS

EOS Emotec D Manuel utilisateur

EOS

EOS EmoTouch II + Manuel utilisateur

EOS

EOS Compact D18 Manuel utilisateur

EOS

EOS ECON I1 Guide de l'utilisateur

EOS

EOS EmoTouch 3 Manuel utilisateur

EOS

EOS ECON H2 Manuel utilisateur

EOS

EOS ECON 45A2 Guide de planification

EOS

EOS EmoTec LSG 09R Guide de planification

EOS

EOS EMOTEC L 09 Guide de planification

EOS

EOS Emotec D Manuel utilisateur

EOS

EOS ECON F1 Manuel utilisateur

EOS

EOS ECON D1 Guide de l'utilisateur

EOS

EOS KUSATEK K-Tec Manuel utilisateur

EOS

EOS SBM-IR Modul Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur