Enersound TP-600 Manuel utilisateur

TP-600 FM Transmitter Operating Manual

LCD Full Display:

1. : Battery capacity indicator

2. : 2:1 Compression Ratio, :1:1 Compression Ratio

3. : Key Locked Icon

4. : Menu Icon & Microphone Mute Icon (flashing)

5. : Function indicator during Menuoperation

6. : Channel number indicator in standby mode

7. : Channel number indicator in Priority setting mode

8. : FM deviation indicator

General Operation Mode:

1. Power ON/OFF & Transmission: Hold press the [ ] button 3 seconds will turn on the radio, it will

be in standby mode (see LCD display of Fig 1). When plug in the external Microphone, it will turn on

the TX LED & in transmission mode, if remove the Microphone will stop transmission, the TX LED turn

off.

Fig 1

Hold press the [ ] button 3 seconds again will turn off

the device.

(2) MIC MUTE setting: At radio operating mode, press the MIC Mute button once to turn on this function

(see LCD display of Fig 2), the Mute LEDwill be flashing, the External Microphone will be disable. .

Fig 2

Press the MIC Mute button again will turn off this function & mute the Microphone, the LCD Micon will

disappear & turn off the red LED.

(3) Audio Modulation indicator: There are 3 level’s icon (25, 50, 75) to indicate the audio input level, when

level over the 25KHz deviation, the 25icon will on, when level over the 50KHz deviation, the 25, 50

icons will on, when level over the 75KHz deviation, the 25, 50, 75icons will turn on at same time

(see LCD display of Fig 3).

Fig 3

(4) Button Lock function: This function is used to lock all the buttons except the [Mute] and [ ] button

during operating. Hold press [ ] button for 3 seconds to turn on this function, then LCD  icon

will on (see LCD display of Fig 4). Press and hold the [ ] button for 3 seconds again, it will turn off

this function &  icon disappear.

Fig 4

(5) Transmit Channel setting: At operating mode, press the [ ] or [ ] button to choose the

operating channel (see LCD display of Fig 5), it will turn off transmission about 250ms during the

switching.

Fig 5

(6) Standard Mode Pre-Setting: Hold press the [Menu] button 3 seconds into the setting mode (see

LCD display of Fig 6, the 6Aicon means gainwhich be flashing before adjust), there are 2 function’s

parameter (Major Volume & AUX) to set in this mode.

(6.1) Major Volume: Press the [ ] or [ ] button to increase or decrease the Volume level, there are

32 setting levels, the default level is 16, short press the [ (Menu)] button to store & go to the next

setting (AUX Volume ).

Fig 6

(6.2) AUX Volume: The Fig 7 is LCD display of this mode, the LCD icon 6Awill be flashing before adjust,

press the [ ] or [ ] button to increase or decrease the Volume level, there are 32 setting levels, the

default level is 16, short press the [Menu] button to store & go to the next setting (Advance Setting).

Fig 7

(7) Advance Function: The user doesn’t modify the Advance Settingusually, so it needs to re-confirm

before modification. In AUX Volumemode, press the [Menu] button will go to the Advance Setting

mode, (see LCD display of Fig 8), the display will be flashing in the beginning. Press the [ ] or []

button to choose No(Fig 9) & YES(Fig 10), then press the [Menu] to store & go to the Compress

Ration (1st parameter) setting. There are 4 parameter be able to set in this mode.

Fig 8

Fig 9

Fig 10

(7.1) Compress Ratio: This function is used to choose the suitable compress ratio for input signal, it may

improve the signal to noise ratio to get better performance during operating. The display will be flashing in

the beginning, press the [ ] or [ ] button to choose the compression ratio C 1:1 or 2:1. (see Fig 11 &

Fig 12), then press [Menu] button to store & go to the next setting, the default setting is 1:1.

Fig 11.

Fig 12.

(7.2) LCD Display mode: There are two different display type (Channel No.& Frequency) for the

operating channel, the display will be flashing in the beginning, press the [ ] or [ ] button to choose

(see LCD display of Fig 13 & Fig 14), then press [Menu] button to store & go to the next setting, the default

setting is Channel No.

Fig 13 (Channel No.)

Fig 14 (Frequency)

(7.3) Battery Type Selector mode: There are two different battery type (Re-chargeable Ni-MH-& Alkaline)

be able to choose in this mode, the display will be flashing in the beginning, press the [ ] or [ ]

button to choose (see Fig 13 & Fig 14), then press [Menu] button to store & go to the next setting, the

default setting isrECH.

PS. When user choose the Alkaline& plug in charging cradle, the radio will cut off the charging

connection automatically, the LCD display will indicate the Error(see Fig 17) & the green LED will be

flashing to warning it.

Fig 15

Fig 16

Fig 17

(7.4) Reset to default setting: In Battery Selectormode, press [Menu] button once to the cLEAr data

mode (see fig 18)., Press the [ ] or [ ] button to choose YES(Fig 19) or No(Fig 20). In YES

mode, press the [Menu] will return to the program default channel of the Standardmode.

Fig 18

Fig 19

Fig 20

Noted:

(a) When user press any button, the LCD backlight will turn on automatically, it will turn off after 5

seconds if don’t press button.

(b) In Standard Band Presettingmode, if don’t press button more than 10 seconds, it will go back to

the previous channel w/o store the setting. If press the [Menu] button 3 seconds, it will store the

setting & go back to the Standard Bandmode.

(d) The Batter Type Selectoris not in the Resetlist

Preset Band: At power off mode, hold press the & button 10 seconds to the Band

selectormode. There are two bands (Standard& Preset) in this system, the operating band will be

switching automatically. The Presetband has two preset channel (P1& P2). At Standardband

mode, turn off the power, then hold press the & button 10 seconds will go to the Preset

band mode (see LCD display Fig 21), press [ ] or [ ] button to choose YES(or no), choose YES

& press button to the P1/P2 select mode, LCD display P1(see Fig 22), then press   button to

choose P1 channel setting mode (see LCD display Fig 23).

(1) P1 Channel Setting: Hold press   button 3 seconds to the channel modify mode the LCD

display be flashing, press [ ] or [ ] button to choose the preset channel, then press  

button to store & go to the next setting.

Fig 21

Fig 22

Fig 23

(1.1) P1 Major Volume Setting: In this setting mode, the LCD display as Fig 6, the icon GAis flashing

before setting, press the [ ] or [ ] button to increase or decrease the Volume level, there

are 32 setting levels, the default level is 16, short press the [ ] button to store & go to the

next setting (AUX Volume ).

(1.2) P1 AUX Volume Setting: In this setting mode, the LCD display as Fig 7, the io GA is flashig

before setting, press the [ ]or [ ] button to increase or decrease the Volume level, there

are  settig levels, the default level is 6, short press the Meu utto to store & go to the

next setting (Advance Setting).

(1.3) P1 Advance Function: In this setting mode, the LCD display as Fig 8, the display icon AdSET will

be flashing in the beginning. Press the [ ]or [ ] utto to hoose No Fig  & or YES

(Fig 10), then press the [Menu] to store exit or & go to the Compress Ration (1st parameter)

setting. There are 4 parameter be able to set in this mode.

(1.4.1) Compress Ratio: This function is used to choose the suitable compress ratio for input signal, it may

improve the signal to noise ratio to get better performance during operating. The display will be

flashing in the beginning, press the [ ] or [ ] button to choose the compression ratio C 1:1

or 2:1. (see Fig 11 & Fig 12), then press [Menu] button to store & go to the next setting, the

default setting is 1:1.

(1.4.2) LCD Display mode: There are two different display type (Channel No.& Frequency) for the

operating channel, the display will be flashing in the beginning, press the [ ] or [ ] button

to choose (see LCD display of Fig 13 & Fig 14), then press [Menu] button to store & go to the

next setting, the default setting is Channel No.

(1.4.3) Battery Type Selector mode: There are two different battery (AAtype of Re-chargeable &

Alkaline) be able to choose in this mode, the display will be flashing in the beginning, press the

[ ] or [ ] button to choose (see Fig 13 & Fig 14), then press [Menu] button to store & go

to the et settig, the default settig is rECH(Re-chargeable battery).

Noted: The Batter Type Selectoris not in the Resetlist

(1.4.4) Reset to default settig: I Batter Seletor ode, press Meu utto oe to the LEAr

data ode see fig ., Press the [ ] or [ ] utto to hoose YES Fig  or No

Fig . I YES ode, press the Meu will return to the program default channel of the

Standard ode.

Noted: (1) In Preset Band Presettingmode, if don’t press button more than 10 seconds, it will go back

to the previous channel w/o store the setting. If press the [Menu] button 3 seconds, it will store

the setting & go back to the Standard Bandmode.

(2) All Advancefunction setting would be used both Standard’& Preset (P1 & P2)band.

(2) P2 Preset: At standard mode & power off status, hold press the & button 10 seconds to

the P1/P2selector mode (see LCD display Fig 20), press [ ] or [ ] button to choose YES(or

no), Press button to the LCD display P1, press [ ] or [ ] button to choose P2then

press   button to the P2 channel setting mode (see LCD display Fig 24).

(2.1) P2 Channel Setting: Hold press   button 3 seconds to the channel modify mode the LCD

display be flashing (see Fig 25), press [ ] or [ ] button to choose the preset channel, then

press   button to store & go to the next setting.

Fig 25

(2.2) Major Volue Settig: I this settig ode, the LCD displa as Fig 6, the io GA is flashig efore

setting, press the [ ] or [] button to increase or decrease the Volume level, there are 32 setting

levels, the default level is 6, short press the  ] button to store & go to the next setting (AUX

Volume ).

(2.3) P1 AUX Volume Setting: In this setting mode, the LCD display as Fig 7, lay be flashing, the icon

GA is flashig efore settig, press the [ ] or [ ] button to increase or decrease the Volume

level, there are  settig levels, the default level is 6, short press the Meu utto to store & go

back to the P2 channel setting.

(3) Change to Standard Band: At Presetband, if you would like to choose Standardband,

you have to turn off the power, hold press the   &   utto  seods, the LCD display

Autres manuels pour TP-600

Table des matières

Autres manuels Enersound Émetteur

Enersound

Enersound T588-15 Manuel utilisateur

Enersound

Enersound TP-600 Manuel utilisateur

Enersound

Enersound T-588 Manuel utilisateur

Enersound

Enersound T?500 Manuel utilisateur

Enersound

Enersound T?500 Manuel utilisateur

Enersound

Enersound T-500-4 Manuel utilisateur

Enersound

Enersound T-588 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur