Emerson Bettis TEC2 Manuel utilisateur

User Manual

Part Number: 87340-1001, Rev. 0

Release: April 2015

User Manual for TEC2 Display Module

(Model 87340)

User Manual

Part Number: 87340-1001, Rev. 0 April 2015

Display Module

Section 1: Display Module

1.1 Local Display Module

Display Module with Bluetooth®- Model 87340.

The Local Display module consists of the following as shown in Figure 1:

• Graphics Display

• Message Center

• Control Knob and Selector Knob

• Three LEDs

Figure 1 Local Display Module (LDM)

1.1.1 Graphics Display and Message Center

The graphics display shows the mode of operation, valve status, position, torque, and

alarm symbols. The message center displays actuator setup selections, data entry

feedback, and alarm messages. When no alarms are active and the valve is not moving

or is not at either limit, the message center will be blank.

1.1.2 Control Knob and Selector Knob

The control knob performs normal Open/Stop/Close function in the local control mode

and YES/NO function in the“MONITOR/SETUP”mode as detailed in Table 1.

The NO selection increments the displayed value but does not decrement.

To decrement continuously hold the NO position until the highest value is reached.

The display value will then start at the lowest value and increment from there. If the

control knob is held in the NO position for more than 2 seconds the incrementing rate

will increase from 0.5 seconds per new value to 0.1 seconds per value.

LEDs

Graphics Display

Message Center

Control Knob

Selector Knob

April 2015

User Manual

Part Number: 87340-1001, Rev. 0

Display Module

The selector knob performs normal selector switch Local/Stop/Remote function and

alternate Next/Back display function in the “MONITOR/SETUP” mode as detailed

in Table 1.

The NEXT and BACK selections are used strictly for cycling through the SETUP displays

to locate the desired display or to exit the “SETUP” mode.

Table 1. LDM Rotating Knobs

Knob Rotation Direction Function Result

Control

Spring return to

center

Neutral

Position

Completes YES or NO entry cycle.

Exception: when knob is held for

continuous data entry updates.

Clockwise

(CLOSE) YES

Accepts the displayed question or

data entry. Advances to the next

display.

Exception: when knob is held for

continuous data entry updates.

Counterclockwise

(OPEN) NO

Rejects displayed question or data.

Increments to the next data value or

display. Exception: when knob is

held for continuous data entry

updates.

Selector STOP Neutral

Position

Sets up entry, completes NEXT or

BACK entry cycle. See Note below

Clockwise

(REMOTE) NEXT Advances to the next display

Counterclockwise

(LOCAL) BACK Returns to the previous display

NOTE:

If the selector knob remains in either NEXT or BACK position, the display will scroll.

1.1.3 LEDs

There are three LEDs on the LDM:

• Red

• Green

• Yellow

The default function of these LEDs is detailed in Table 2.

1.1.4 Normal Display Function

Figure 2 details the display during normal function. The bar graphs, position digits,

icons, and LEDs indicate normal activity, that is, the valve opening, closing, or stopping

in mid-travel. The message center remains blank until alarms are active or the valve is

opening, closing, full open, or full close.

Table 2 details various normal activities and how each is displayed.

User Manual

Part Number: 87340-1001, Rev. 0 April 2015

Display Module

Figure 2 Normal Display

The valve has stopped and is 75% opened. The yellow LED is ON and the message

center is clear.

Table 2. Normal Display Functions

Valve

Activity

Message

Center

Top Line

Display Functions (LEDs) Position

Bar Graph

Percent

Open

"XX%"

Yellow Red Green

Fully

closed

FULL

CLOSE OFF OFF ON 0%

Opening OPENING OFF Blinking OFF

Flashing in

the Open

direction

Increments

Stopped Cleared ON OFF OFF

STOP Icon is Displayed

Shows

relative

position

% open

Fully

opened

FULL

OPEN OFF ON OFF 100%

Closing CLOSING OFF OFF Blinking

Flashing in

the Close

direction

Decrements

Alarm

Alarm Type

Displayed

-Bottom

Line

Blinking OFF OFF

Alarm Icon

April 2015

User Manual

Part Number: 87340-1001, Rev. 0

Display Module

1.2 Remote Display Module (RDM)

Display Module with Bluetooth®- Model 87340

The RDM performs the same functions as the LDM.

NOTE:

If the RDM does not receive communication messages from the Central Control Module (CCM)

within 5 seconds after power is applied, the RDM will display the ashing message “CCM LINK

FAILED” and all three LEDs will blink. This will also occur if communication is lost for 5 seconds

or more.

If RDM 1 or 2 is enabled and not connected, the actuator will be in stop mode and cannot be

operated until RDM is connected or disabled.

1.2.1 RDM Operation with LDM

Two RDMs and an LDM can be connected to one actuator. The operation priority is

detailed in Table 3.

Table 3. RDM and LDM Operation Priority

Mode of Operation LDM, RDM #1, RDM #2 and Selector Switch Position

STOP At least one module must have the selector switch in the STOP

position.

LOCAL At least one module must have the selector switch in the LOCAL

position and none have the selector switch in the STOP position.

REMOTE All modules must have the selector switch in the REMOTE

position.

For complete list of sales and manufacturing sites, please visit

www.emerson.com/actuationtechnologieslocations or contact us at

info.actuationtec[email protected]

World Area Conﬁ guration Centers (WACC) offer sales support, service,

inventory and commissioning to our global customers.

Choose the WACC or sales ofﬁ ce nearest you:

NORTH & SOUTH AMERICA

19200 Northwest Freeway

Houston TX 77065

USA

T +1 281 477 4100

Av. Hollingsworth

325 Iporanga Sorocaba

SP 18087-105

Brazil

T +55 15 3413 8888

ASIA PACIFIC

No. 9 Gul Road

#01-02 Singapore 629361

T +65 6777 8211

No. 1 Lai Yuan Road

Wuqing Development Area

Tianjin 301700

P. R. China

T +86 22 8212 3300

MIDDLE EAST & AFRICA

P. O. Box 17033

Jebel Ali Free Zone

Dubai

T +971 4 811 8100

P. O. Box 10305

Jubail 31961

Saudi Arabia

T +966 3 340 8650

24 Angus Crescent

Longmeadow Business Estate East

P.O. Box 6908 Greenstone

1616 Modderfontein Extension 5

South Africa

T +27 11 451 3700

EUROPE

Holland Fasor 6

Székesfehérvár 8000

Hungary

T +36 22 53 09 50

Strada Biffi 165

29017 Fiorenzuola d’Arda (PC)

Italy

T +39 0523 944 411

www.emerson.com/bettis

The Emerson logo is a trademark and service mark of Emerson Electric Co.

BettisTM is a mark of one of the Emerson family of companies.

All other marks are property of their respective owners.

The contents of this publication are presented for information purposes

only, and while every effort has been made to ensure their accuracy,

they are not to be construed as warranties or guarantees, express or

implied, regarding the products or services described herein or their use

or applicability. All sales are governed by our terms and conditions, which

are available on request. We reserve the right to modify or improve the

designs or specifications of our products at any time without notice.

Autres manuels pour Bettis TEC2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Unité de contrôle

Emerson

Emerson Fisher 161 Series Manuel utilisateur

Emerson

Emerson Numatics DeviceLogix G2-2 Series Manuel d'instructions

Emerson

Emerson Fisher EU Manuel utilisateur

Emerson

Emerson KTM Series Manuel

Emerson

Emerson Alco Controls TIH FLR Series Manuel utilisateur

Emerson

Emerson FISHER CV500 Manuel utilisateur

Emerson

Emerson Bettis 2000 Series Manuel utilisateur

Emerson

Emerson SM-I/O 24V Protected Manuel utilisateur

Emerson

Emerson ENARDO 860 Series Manuel utilisateur

Emerson

Emerson IEC 62591 Manuel utilisateur

Emerson

Emerson Baumann 83000 Manuel utilisateur

Emerson

Emerson Fisher V500 Manuel utilisateur

Emerson

Emerson AVENTICS 501 Series Manuel utilisateur

Emerson

Emerson Fisher Type 289P Manuel utilisateur

Emerson

Emerson Anderson Greenwood 81 Series Manuel utilisateur

Emerson

Emerson Fisher NPS 8 CHP Manuel utilisateur

Emerson

Emerson Fisher GX Manuel utilisateur

Emerson

Emerson Fisher Large ET Manuel utilisateur

Emerson

Emerson Tartarini V Series Manuel utilisateur

Emerson

Emerson KEYSTONE F635 Instructions d'installation

Emerson

Emerson Bettis OM3 Manuel utilisateur

Emerson

Emerson ALCO CONTROLS BVE Series Manuel utilisateur

Emerson

Emerson Fisher Baumann 24000S Manuel utilisateur

Emerson

Emerson Clarkson series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur