Elvid OCM-10-PSM Manuel utilisateur
USER
MANUAL
FIELDVISION
OCM-10-PSM
10.1″PRO LCD MONITOR
Thank you for choosing Elvid.
The Elvid OCM-10-PSM FieldVision 10.1″Pro LCD Monitor with Scopes is perfect as a
director’s monitor. Its signature all-scopes setting displays a histogram, audio column,
vector, RGB histogram, and YUV waveform on the sides with an uninterrupted view of your
incoming video frame, enabling instant and constant feedback without disrupting your view
of the image. Anamorphic mode can be set to 1.3× or 2.0× to offer an accurate view of your
picture’s aspect ratio when shooting with an anamorphic lens.
The unique nine-grid mode divides the frame into a 3 × 3 grid as a composition aid and
allows you to magnify a specic area without adjusting your frame. A zebra exposure
indicator and false color mode with onscreen key display provide visual guides so you can
achieve precise exposure levels. A focus assist tool with two sensitivity levels helps ne-tune
your focus. There are also broadcast-specic features like overscan, safety frame markers,
and a tally light.
The FieldVision is equipped with Video, YPbPr, HDMI, and two SDI inputs—all with loop-
through—making this monitor compatible with most pro-video connections. Native resolution
is 1280 × 800, and you can easily change the native 16:10 aspect ratio to t your needs.
Onboard controls include ve function buttons that can be programmed from a palette of
22 functions and saved in three independent groups. Four knobs facilitate menu navigation,
access focus and Camera (DSLR) modes, and adjust monitor settings. There’s also an
integrated mono speaker and a 3.5 mm stereo headphone output for live audio monitoring.
INTRODUCTION
2
3
• Please read and follow these instructions and
keep this manual in a safe place.
• Exposure to high sound levels can cause
permanent hearing loss. Avoid listening at
high volumes for extended periods of time.
• Keep this product away from water and any
ammable gases or liquids.
• Make sure this product is powered off when
plugging it into a power source.
• Use only the correct, recommended voltage.
• Do not attempt to disassemble or repair this
product.
• Do not place or store the FieldVision
facedown, since this can damage the screen.
• Handle this product with care. Avoid any
unnecessary impacts to this product.
• Do not block the vents in this product.
• Disconnect this product from its power source
before storage and during electrical storms.
• Do not use chemical solutions to clean this
product. Clean this product with only a soft,
dry cloth.
• Keep this product away from children.
• Make sure that this product is intact and that
there are no missing parts.
• To avoid damage to this product, be careful
not to overtighten or improperly thread any
of the threaded ttings.
• All photos are for illustrative purposes only.
PRECAUTIONS
TABLE OF
CONTENTS
Precautions.............................................. 3
Product Contents ................................... 5
Overview .................................................. 6
Powering the FieldVision ..................... 8
Monitoring Sound................................... 9
Mounting the FieldVision..................... 9
Connecting to Your Camera ................. 9
Loop Through .......................................... 9
Tally Connection ..................................... 9
The Sunshade........................................ 10
The Menu ................................................ 11
Navigating the Menu............................ 11
Assistant Functions Menu .................. 11
Check Field ............................................. 11
Pseudo Color .......................................... 11
Zebra Crossing....................................... 11
Focus Assist ........................................... 11
Focus Color ............................................. 11
Pattern Gen ............................................ 11
Marker Display Menu........................... 11
Center Marker........................................ 11
Marker Type............................................12
Safety Area.............................................12
Marker Color...........................................12
Nine Grid .................................................12
Scopes Menu ..........................................13
Y Histogram............................................13
Audio Column.........................................13
Vector.......................................................13
RGB Histogram ......................................13
Waveform................................................13
All Scopes................................................13
Picture Setting Menu ...........................14
Scan Mode ..............................................14
Camera Mode .........................................14
Flip............................................................14
Freeze.......................................................14
Pixel to Pixel ..........................................14
Zoom ........................................................14
Anamorphic ............................................14
Color Setting Menu...............................15
Color Temp ..............................................15
Red, Green, and Blue............................15
Shortcuts Menu .....................................15
Shortcut Group ......................................15
OSD Setting Menu.................................16
Language.................................................16
OSD Time.................................................16
OSD Trans ...............................................16
Volume.....................................................16
Mute.........................................................16
Reset ........................................................16
SW Version .............................................16
Specications .........................................17
Supported Resolutions and Frame Rates 18
Troubleshooting.....................................19
One-Year Limited Warranty.........(Back) 20
4
PRODUCT
CONTENTS
·10.1″Field Monitor
·Sunshade
·Sunshade thumbscrews (×2)
·Tabletop bracket
·Tabletop bracket thumbscrews (×2)
·Adhesive touch strip
·Tally kit
·4-pin XLR power supply
·AC power cable
·User manual
5
OVERVIEW
6
Brightness/Esc knob
Contrast/Focus knob
Headphone jack
Function buttons
(F1, F2, F3, F4, F5)
Speaker
Selector/Menu knob
Volume/Camera knob
Video input buttons
(Video, YPbPr, HDMI, SDI 1, SDI 2)
Power LED
Screen
1/4″-20 threaded sockets
Tally Light
Power switch
Tally connector
Battery plate
7
SDI ports
DC power input HDMI input
YPbPr component
video ports
Audio inputs
XLR input HDMI output
POWERING THE
FIELDVISION
There are three ways to power the
FieldVision: 4-pin XLR input, 12 V DC
input, and a Sony L-Series camera
battery.
4-PIN XLR
To power the FieldVision via the 4-pin
XLR input, use a 4-pin XLR power supply
and AC power cable to connect the
FieldVision’s 4-pin XLR DC power input
to your power source.
To power the FieldVision via the 4-pin
XLR input, follow these steps:
1. Fully insert a 4-pin XLR power supply
into the 4-pin XLR DC power input on
the back of the monitor. The connector
should click into place when fully
inserted.
2. Use an AC power cable to connect
the XLR power supply to your AC power
source.
To turn on the FieldVision, press the
power switch to the On position. The
power indicator LED will glow green.
12 V DC INPUT
To power the FieldVision via the 12 V DC
input, use a 12 V DC adapter with the
included 2.1 mm DC barrel to connect
the FieldVision’s DC power input to your
AC power source.
To turn on the FieldVision, press the
power switch to the On position. The
power indicator LED will glow green.
CAMERA BATTERY
The FieldVision has a built-in battery
plate that accepts all Sony L-Series
batteries. This allows you to power the
FieldVision with readily-available battery
packs that you may already own.
To power the FieldVision with a Sony
L-Series battery (not included), follow
these steps:
1. Place a compatible battery in the
battery plate. Make sure the battery’s
bottom contacts are aligned with the
contacts in the battery plate.
2. Slide the battery forward until it locks
into place.
To turn on the FieldVision, press the
power switch to the On position. The
power indicator LED will glow green.
8
GETTING
STARTED
MONITORING SOUND
You can monitor sound via the
integrated speaker or the 3.5 mm
stereo headphone jack. To monitor via
the headphone jack, plug in a pair of
compatible headphones.
MOUNTING THE FIELDVISION
Use one of the 1/4″-20 threaded sockets
in the FieldVision to attach the monitor
to your mounting system. Make sure
your bracket can support the monitor.
Alternatively, you can mount the
included tabletop bracket by attaching it
with the included bracket thumbscrews.
CONNECTING TO YOUR CAMERA
To connect the FieldVision to your
camera, follow these steps:
1. Choose the desired video signal, and
use the appropriate cable to connect
your camera to the corresponding input
connections on the back of the monitor.
2. Press the video input button
(composite video, YPbPr, HDMI, SDI1,
or SDI2) that corresponds to your video
input signal.
LOOP THROUGH
The FieldVision is equipped with loop-
through, also known as pass-through, for
all of its video inputs. To loop the video
signal through the monitor, connect your
camera to the desired video input, and
then connect the appropriate cable to
the corresponding output on the back of
the monitor.
TALLY CONNECTION
If desired, you can connect your tally
cable to the FieldVision’s RS232
D-sub 9-pin tally connector or the
included bare-end adapter. Refer to the
included insert for the specic tally pin
connections.
9
THE
SUNSHADE
10
THE SUNSHADE
The sunshade prevents glare on the
monitor’s screen by blocking out stray
light and is useful when shooting
outdoors. To attach the included
sunshade, follow these steps:
1. Unfold the sunshade and place it along
the top and sides of the monitor.
Tip: For a more secure t, attach the
included adhesive touch strip along the
top edge of the monitor. This will help
hold the sunshade in position.
2. Align the sunshade’s screw holes with
the 1/4″-20 threaded sockets in the sides
of the monitor.
3. Use the included thumbscrews to
fasten the sunshade in place.
Table des matières
Autres manuels Elvid Moniteur
Elvid
Elvid FIELDVISION OCM-89-4KH Manuel utilisateur
Elvid
Elvid RVM-7B-ALT Manuel utilisateur
Elvid
Elvid OCM-7P-HDR Manuel utilisateur
Elvid
Elvid OCM-7B-4KV2 Manuel utilisateur
Elvid
Elvid WCM-758G SkyVision Manuel utilisateur
Elvid
Elvid STUDIOVISION SRM-7X2-4KH Manuel utilisateur
Elvid
Elvid OCM-101-4KH Manuel utilisateur
Elvid
Elvid Studiovision STV-150-4KH Manuel utilisateur
Elvid
Elvid OCM-7PWV Manuel utilisateur
Elvid
Elvid OCM-7B-D FieldVision Manuel utilisateur
